丙烯酸水溶液聚合法制备PTFE/PAA/Nafion膜及其性能

采用廉价的多孔聚四氟乙烯(PTFE)膜作为基底, 用少量的Nafion与PTFE膜复合可制备低成本的质子膜. 但疏水性的PTFE膜与亲水性的Nafion膜结合性不佳. 基于此, 本文对疏水性的PTFE膜材料表面进行设计, 先采用丙烯酸对疏水性的PTFE膜表面进行亲水性改性, 再喷涂亲水性Nafion膜, 完成低成本PTFE/PAA/Nafion膜的制备. 实验结果表明, 改性前的PTFE膜材料水接触角为150°, 改性后的膜接触角变为55.6°, 亲水性大幅上升, 膜的机械强度和尺寸稳定性(断裂强度为25.2 MPa, 80 ℃下的溶胀率为11.9%)均优于Nafion117膜, 而 Nafion用量则节省了60%. PTFE/PAA/Nafion膜具有高质子导通率(80 ℃下达到131.9 mS/cm), 接近于Nafion117膜, 最大功率密度可以达到404.2 mW/cm².     

BiOCl0.5Br0.5/BiPO4双层异质结薄膜光催化剂的一步电化学法制备及性能

采用一步电化学法在金属 Bi板上成功制备了 Bi OCl_0.5Br_0.5/Bi PO₄双层异质结薄膜,并通过多种表征手段对薄膜的晶型结构、元素组成及化合价、形貌和尺寸特征、吸光性能和荧光强度进行了表征。结果表明,制备得到的复合薄膜呈现出上层为梭子状的 Bi PO₄颗粒层分散在下层为 Bi OCl_0.5Br_0.5固溶体层的双层结构。这样的双层膜排列顺序使得光生电子和空穴在不同组分之间的界面电场作用下分别向薄膜两侧流动,促进光致载流子的分离,提高了 Bi OCl_0.5Br_0.5/Bi PO₄复合薄膜的光催化活性。活性测试结果表明,在模拟太阳光照射 120 min 后,Bi OCl_0.5Br_0.5/Bi PO₄复合薄膜对苯酚的降解率达到了 99.97%,是相同条件下制备的 Bi OCl/Bi PO₄和 Bi O...     

Porous multicomponent chitosan/poly(ε-caprolactone)-block poly (ethylene glycol)/SiO2 aerogel@polydopamine membrane for Congo red adsorption

A composite adsorbent, chitosan//poly (ε-caprolactone)-block poly (ethylene glycol)/SiO₂ aerogel@polydopamine (CS/PCL-b-PEG/SA@PDA) membrane was prepared for the adsorption of organic dyes. The matrix polymer materials of this novel adsorbent were eco-friendly. SiO₂ aerogel with nanoporous network construction was fixed in the multicomponent polymer fibers through simultaneous electrospinning-electrospray technology followed by modification of polydopamine (PDA). The composite adsorbent had a maximum adsorption capacity of 598.8 mg/g for Congo red (CR) and possessed good reusability performance. This adsorbent showed excellent performance for the selective adsorption of relatively large molecule CR dyes even under high concentration of small molecule methyl orange (MO) dyes or 1 M of salt solution. The adsorption mechanism indicated that the –NH₂ and –OH groups in adsorbent could generate the stronger electrostatic attraction with the –SO₃^- groups in CR. Meanwhile, the sufficient adsorption spaces of the adsorbent were constructed by the porous network structure of SiO₂ aerogel, the accumulation of PDA particles and the porous structure of the multicomponent composite membrane. The work provided a proactive study in designing an adsorbent for the selective adsorption of organic dyes.     

Control of pore environment in highly porous carbon materials for C2H6/C2H4 separation with exceptional ethane uptake

Adsorptive separation of C₂H₆ from C₂H₄ by adsorbents is an energy-efficient and promising method to boost the polymer grades C₂H₄ production. However, that C₂H₆ and C₂H₄ display very similar physical properties, making their separation extremely challenging. In this work, by regulating the pore environment in a family of chitosan-based carbon materials (C-CTS-1, C-CTS-2, C-CTS-4, and C-CTS-6)- we target ultrahigh C₂H₆ uptake and C₂H₆/C₂H₄ separation, which exceeds most benchmark carbon materials. Explicitly, the C₂H₆ uptake of C-CTS-2 (166 cm³/g at 100 kPa and 298 K) has the second-highest adsorption capacity among all the porous materials. In addition, C-CTS-2 gives C₂H₆/C₂H₄ selectivity of 1.75 toward a 1:15 mixture of C₂H₆/C₂H₄. Notably, the adsorption enthalpies for C₂H₆ in C-CTS-2 are low (21.3 kJ/mol), which will facilitate regeneration in mild conditions. Furthermore, C₂H₆/C₂H₄ separation performance was confirmed by binary breakthrough experiments. Under different ethane/ethylene ratios, C-CTS-X extracts a low ethane concentration from an ethane/ethylene mixture and produces high-purity C₂H₄ in one step. Spectroscopic measurement and diffraction analysis provide critical insight into the adsorption/separation mechanism. The nitrogen functional groups on the surface play a vital role in improving C₂H₆/C₂H₄ selectivity, and the adsorption capacities depend on the pore size and micropore volume. Moreover, these robust porous materials exhibit outstanding stability (up to 800 °C) and can be easily prepared on a large scale (kg) at a low cost (～$26 per kg), which is very significant for potential industrial applications.     

Preparation and fabrication of porous-Fe2O3/carbon black nanocomposite: a portable electrochemical sensor for psychotropic drug detection in environmental samples

Herein, we reported the fabrication of porous iron oxide/carbon black (P–Fe₂O₃/CB) composite through a two-step engineering method. At first, Prussian blue microcubes were used as a precursor and further calcined to form P–Fe₂O₃ microcubes. The intercalation of CB nanoparticles with P–Fe₂O₃ nanocubes was processed through the ultrasonication method. The obtained P–Fe₂O₃/CB were successfully scrutinized through various physiochemical characterization methods. The proposed P–Fe₂O₃/CB-modified glassy carbon electrode sensor was successfully implemented in the electrochemical sensing of chlorpromazine hydrochloride due to its very low charge transfer resistance (R_ct) compared to the other electrode modifiers. The sensitive detection of CPMH through differential pulse voltammetry exemplifies an excellent electroanalytical performance such as a wide linear range of 0.5–1472 μM, a lower detection limit (0.001 μM), and an appraisable sensitivity of 1.99 μA/μM cm^?2 due to its availability of a high number of active sites and its large surface area, respectively. It also expresses excellent selectivity, repeatability, reproducibility, and stability results. Moreover, the practical feasibility of the as-fabricated P–Fe₂O₃/CB/glassy carbon electrode sensor shows exquisite recovery (98.1–100.8%) results with an appraisable current response in various biological, pharmaceutical, and environmental samples.     

Preparation of Quercus mongolica leaf-derived porous carbon with a large specific surface area for highly effective removal of dye and antibiotic from water

Quercus mongolica leaf (QL), an easily available biomass, was used as the precursor for preparing the hierarchical porous carbon with a large specific surface area and high adsorption capacities toward the representative dye and antibiotic. After being carbonized, QL was further chemically activated, and potassium hydroxide was proved to be a better activator than sodium hydroxide. The QL-derived porous carbon (PCQL) exhibited abundant micro- and mesopores, and the specific surface area reached 3275 m² g^?1. The performances of PCQL were evaluated through adsorbing rhodamine B (RhB) and tetracycline hydrochloride (TC) from water. Four adsorption isotherm models (the Langmuir, Freundlich, Sips, and Redlich-Peterson models), three adsorption kinetic models (the pseudo-first-order, pseudo-second-order, and intra-particle diffusion models), and the thermodynamic equations were used to investigate the adsorption processes. The pseudo-second-order kinetic model and the Sips isotherm model fitted the experimental data well, which indicates that the adsorption processes were controlled by the amount of adsorption active sites on the surface of PCQL, and these adsorption active sites had different affinities for the adsorbates. The maximum adsorption capacities of PCQL toward RhB and TC were 1946.0 and 1479.6 mg g^?1, respectively, based on the Sips model. The thermodynamic analysis indicates that the adsorption of PCQL toward adsorbents was spontaneous physical processes accompanied by the increasing disorder degree. The adsorption mechanism was attributed to the combination of the pore-filling, hydrogen bond, and π-π interactions. Moreover, in the fixed-bed experiments, the Yoon-Nelson model fitted the breakthrough curves well, and about 8 L wastewater containing RhB (200 mg L^?1) may be effectively treated by 1.0 g of PCQL. Above results indicate that QL is a promising precursor for preparing functional porous carbon materials.     

On the Integration of Dielectrometry into Electrochemical Impedance Spectroscopy to Obtain Characteristic Properties of a Dielectric Thin Film

We demonstrate a novel impedimetric approach providing unprecedented insight into characteristic properties of dielectric thin films covering electrode surfaces. The concept is based on the joint interpretation of electrochemical impedance spectroscopy (EIS) together with dielectrometry (DEM) whose informative value is mutually interconnected. The advantage lies in the synergistic compensation of individual shortcomings adversely affecting conventional impedimetric analysis strategies relying exclusively on either DEM or the traditional EIS approach, which in turn allows a reliable determination of thickness and permittivity values. The versatility of the method proposed is showcased by an in-situ growth-monitoring of a nanoporous, crystalline thin film (HKUST-1) on an interdigitated electrode geometry.     

Development of a Chitosan/Nickel Phthalocyanine Composite Based Conductometric Micro-sensor for Methanol Detection

Thin-film composite of chitosan/nickel phthalocyanine (NiPc) was electrochemically deposited on the fingers of interdigitated gold electrodes, applying chronoamperometric polymerization technique. The presence of crystallized NiPc in the chitosan was confirmed by EDX and FTIR analysis. Acetone, ethanol, and methanol gas-sensing properties of the films prepared at optimum conditions were studied at atmospheric temperature, through differential measurements at an optimized frequency of 10 kHz, using a lock-in amplifier. The conductometric sensor presents the highest sensitivity of 60.2 μS.cm⁻¹(v/v) for methanol and 700 ppm as the limit of detection. For validation, the methanol content of a commercial rubbing alcohol was determined.     

嵌段共聚物薄膜快速自组装方法

嵌段共聚物 (BCP) 薄膜可通过不同的退火方法诱导其微相分离,从而获得大面积圆柱状、层状和球状等纳米图案。这些长程有序的纳米结构形态,已经广泛应用在纳米光刻和电子器件等多个领域中。目前,有效且快速的退火方法仍然是BCP薄膜自组装技术中的研究热点。本文首先介绍了制备BCP薄膜纳米结构图案常用的退火技术,然后综述了三种新型快速退火技术,最后分析总结了这些退火技术的优缺点。