基于磷光材料的低给体比例有机太阳能电池

本文以低比例的磷光材料作为给体,制备了基于MoOx/C60:x%Ir(ppy)3的有机太阳能电池(OPV)器件.其中,C60为高比例的受体材料,金属配合物Ir(ppy)3为低比例的给体材料,MoOx为阳极缓冲层.通过一系列不同Ir(ppy)3比例的OPV器件对比研究,得出了最优器件结构.研究发现,当Ir(ppy)3比例足够小时,器件表现为肖特基势垒,开路电压(VOC)较大,短路电流(JSC)较小;随着Ir(ppy)3比例的增加,VOC逐渐减少,而JSC逐渐增大;当进一步增加Ir(ppy)3比例时,VOC趋于稳定,JSC开始减小.结果显示,5%Ir(ppy)3比例的器件性能最佳,效率达1.7%.为了使器件效率得到进一步提升,本研究组采用吸收光谱范围比C60更宽的C70作为受体材料,使光电转换效率进一步提升至3.0%.     

Microwave-assisted sol-gel synthesis of CeO2–NiO nanocomposite based NO2 gas sensor for selective detection at lower operating temperature

The progress in the development of gas sensors has considerably grown using some novel nanomaterials of metal, metal oxide and composite. In the current study, we intended and evaluated the properties of nanomaterials like CeO₂, NiO, and CeO₂–NiO composite and its application as NO₂ gas sensor. Sensing of low concentration of NO₂ gas at optimum functional temperature was succeeded using CeO₂–NiO nanocomposites (NCs) film. The working temperature ranges in between 100 and 225 ?°C. Highly crystalline nanomaterials (CeO₂, NiO and CeO₂–NiO) have been prepared by applying microwave-assisted sol-gel route. The as-prepared nanomaterials are characterized for their structure, size, morphology and constitution by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive X-ray analysis. XRD studies of nanoparticles reveal the formation of nanoscale CeO₂ and NiO with crystallite size 26, 23 ?nm, respectively. Both are having a face centered cubic structure. The nanocomposite (NC) Ce:Ni ?= ?60:40 has crystallite size of 13 ?nm. XRD study of NCs shows assimilation of Ni metal into the ceria and proves physical similarities of two phases. It can be observed from SEM that prepared NC has a porous surface which enables more surface active sites for adsorbing oxygen. The optical properties are measured with the help of UV–Vis. Spectroscopy. Optical band gaps of 3.19, 3.41 and 2.9 ?eV were observed for CeO_2, NiO nanoparticles (NPs) and CeO₂–NiO NC, respectively. Gas sensing properties state that the NC material shows a higher gas response % of 67.34% for NO₂ gas (25 ?ppm) at comparatively low operating temperature (125 ?°C). It gives response time as (～28 ?s) and the recovery (～54 ?s). NiO incorporation in CeO₂ results in a decline of operating temperature of NC and improves the sensing features.     

Crosslinking Super Yellow to produce super OLEDs: Crosslinking with azides enables improved performance

An increasing number of organic light-emitting diodes (OLEDs) is nowadays based on the use of polymers as the emissive material. For this material class in particular, solution-processing of the OLEDs has gained traction in both research and industry. However, in order to access multilayer material systems, orthogonal solvents must be used to prevent dissolution of previously prepared layers. The use of crosslinkers can facilitate this production method by reducing the number of orthogonal solvents needed since insoluble networks are generated. In this work, a novel bisazide crosslinker is employed to insolubilize Super Yellow, a polyphenylene-vinylene emitter. This allows the use of an additional poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine electron blocking layer (EBL) from the same solvent. Devices including the blocking layer show improved efficacies compared to reference devices without the additional EBL, while also maintaining the emission spectrum. Using the upscalable technique of doctor blading, OLEDs were fabricated which showed a particularly noticeable effect of the blocking layer with a nearly twofold increase in luminance and a 56% increase in current efficacy.     

石墨烯嵌锂的拉曼成像

锂离子电池由于具有高能量密度,高循环寿命,低自放电率的优势,成为当前使用最为广泛的储能器件。层状材料是极为常用的负极材料,其微观嵌锂行为的研究对提高电池的能量密度和循环寿命有重要意义。本工作发展了一种新的平板微电池结构,可用于研究锂离子在各类二维层状纳米材料中的嵌锂行为。我们用机械剥离的单片少层石墨烯为正极,热蒸镀的锂金属为负极,构成石墨烯电池,用恒电压放电的方法进行嵌锂测试。采用拉曼成像技术收集石墨烯G峰信号的空间分布,实现对锂的嵌入过程的显微观测。发现了锂在石墨烯中沿层间扩散迁移,以及石墨烯断层对锂扩散的阻碍作用。这些结果有助于理解放电时锂在石墨烯电极中扩散过程,并且这项研究开发的平板微电池结构可用于多种材料的电化学过程中的微观过程表征,同时可实现与光学、电学、电子显微学等多种表征手段的兼容,具有较好的应用前景。     

直接Z型LaNiO3/Mn0.2Cd0.8S异质结催化剂光解水产氢性能及机理探究

以LaNiO_3纳米颗粒为基质,在水热法制备CdS的过程中引入Mn~(2+)离子,原位合成直接Z型LaNiO_3/Mn_(0.2)Cd_(0.8)S异质结光催化剂。分别采用场发射扫描电镜、X射线衍射、X射线光电子能谱、紫外可见漫反射光谱、氮气吸附-脱附测试以及电化学测试等分析方法对制备的催化剂进行表征。在光解水产氢测试中,LaNiO_3/Mn_(0.2)Cd_(0.8)S异质结光催化剂在5 h的H_2产量达到1 190.3μmol,相较于CdS和Mn_(0.2)Cd_(0.8)S,其H_2产量分别提高了 25倍和10倍。荧光和电化学实验证实,Mn~(2+)的引入能够有效地促进光生载流子的分离,同时LaNiO_3/Mn_(0.2)Cd_(0.8)S之间异质结的构筑能有效地促进光生载流子在界面间的迁移、分离,从而促进其光解水产氢效率和稳定性的提高。结合一系列表征和活性测试结果提出直接Z型光解水反应机理,很好地阐述了其光解水产氢活性和稳定性的增强。     

异质结碳纳米管的热整流效率

采用非平衡分子动力学方法, 通过分别控制异质结碳纳米管管径、手性和平均温度的方式研究了异质结碳纳米管的热整流效应. 研究表明, 随着异质结碳纳米管两端几何不对称性的增强, 其热整流效率会随之上升, 而异质结碳纳米管两端的手性的改变和夹角的大小都会对热整流效率产生一定的影响. 热整流效率会随着碳纳米管平均温度的上升而下降. 研究异质结碳纳米管热整流效率对于热二极管、碳纳米散热元器件等潜在应用价值有理论指导作用.     

Observation of room temperature negative differential resistance in solution synthesized ZnO nanorod

We report the observation of negative differential resistance (NDR) in solution synthesized ZnO nanorod. The ZnO nanorod was fabricated as a two terminal planar device using lithographically patterned Au electrodes. The measured current–voltage response of the device has shown a negative differential resistance behavior. The peak-to-valley current ratio of the NDR is found to be greater than 4. The mechanism of this observed NDR effect has been explained based on charge trapping and de-trapping at the nanoscale contacts. It is the first observation of negative differential resistance effect in solution synthesized ZnO nanorod.     

用CdSe/ZnS量子点提高体异质结有机太阳电池的效率

通过掺杂吸收光谱在可见光波段的量子点可提高聚合物对可见光的吸收,因此掺杂CdSe/ZnS核-壳结构量子点(CQDs)能提高聚(3-己基噻吩):[6,6]-苯基-C61-丁酸甲酯(P3HT:PCBM)体异质结太阳电池的能量转换效率.本文研究了CdSe/ZnS量子点在P3HT:PCBM中的不同掺杂比例及其表面配体对太阳电池光伏性能的影响,优化器件ITO(氧化铟锡)/PEDOT:PSS(聚(3,4-乙撑二氧噻吩:聚苯乙烯磺酸)/P3HT:PCBM:(CdSe/ZnS)/Al的能量转换效率达到了3.99%,与相同条件下没有掺杂量子点的参考器件ITO/PEDOT:PSS/P3HT:PCBM/Al相比,其能量转换效率提高了45.1%.     

Impact of the Cd2+ treatment on the electrical properties of Cu2ZnSnSe4 and Cu(In,Ga)Se2 solar cells

The present contribution aims at determining the impact of modifying the properties of the absorber/buffer layer interface on the electrical performance of Cu₂ZnSnSe₄ (CZTSe) thin‐film solar cells, by using a Cd²⁺ partial electrolyte (Cd PE) treatment of the absorber before the buffer layer deposition. In this work, CZTSe/CdS solar cells with and without Cd PE treatment were compared with their respective Cu(In,Ga)Se₂ (CIGSe)/CdS references. The Cd PE treatment was performed in a chemical bath for 7 min at 70 °C using a basic solution of cadmium acetate. X‐ray photoemission spectroscopy measurements have revealed the presence of Cd at the absorber surface after the treatment. The solar cells were characterized using current density–voltage (J–V), external quantum efficiency, and drive‐level capacitance profiling measurements. For the CZTSe‐based devices, the fill factor increased from 57.7% to 64.0% when using the Cd PE treatment, leading to the improvement of the efficiency (η) from 8.3% to 9.0% for the best solar cells. Similar observations were made on the CIGSe solar cell reference. This effect comes from a considerable reduction of the series resistance (R_S) of the dark and light J–V, as determined using the one‐diode model. The crossover effect between dark and light J–V curves is also significantly reduced by Cd PE treatment. Copyright © 2015 John Wiley & Sons, Ltd.     

空心球状C@SnO2@SnS2的制备及光催化去除Cr（Ⅵ）性能研究

将SnO2负载在碳球上通过不完全烧结的方法得到含有大量碳的空心状C@SnO2,随后加入TAA(硫代乙酰胺),利用离子交换法在水热过程中制备了具有不同硫化程度的空心结构的C@SnO2@SnS2三元复合物。利用XRD、FESEM、TEM、XPS、UV-Vis DRS、PL等测试手段对合成样品进行表征,并测试了其光催化去除Cr(VI)的性能。结果表明,C、SnO2和SnS2三者之间的协同作用以及空心结构的形貌显著增强了SnO2的光催化性能,其中CSS-2样品对Cr(VI)具有最佳的去除能力,太阳光照射120 min后对Cr(VI)的去除率高达98.8%。