Flowability and Mechanical and Thermal Properties of Nylon 6/Ethylene bis-Stearamide/Carboxylic Silica Composites

Nylon 6 (PA 6)/ethylene bis-stearamide (EBS)/SiO₂- carboxylic acid-functionalized silica nanoparticles (COOH) composites were prepared by in-situ polymerization of caprolactam. SiO₂-COOH was used to enhance the compatibility between SiO₂ and PA 6 matrix. For comparison, pure PA 6 and PA 6/EBS composites were also prepared via the same method. The PA 6/EBS/SiO₂-COOH composites with low content of EBS and SiO₂-COOH had greater melt-flow index (MFI) (the value of MFI increased by 50%–80%) than the pure PA 6. The results of mechanical properties showed almost no decrease in the tensile strength of PA 6/EBS/SiO₂-COOH composites, with the bending strength decreasing by 17%–21%. However, the Izod impact strength of the PA 6/EBS/SiO₂-COOH composites was greatly improved compared with pure PA 6, which indicated that the toughness of PA 6/EBS/SiO₂-COOH had been greatly improved. The morphology of Izod impacted fractured surfaces of PA 6/EBS/SiO₂-COOH was observed by scanning electron microscopy. The results revealed that the PA 6/EBS/SiO₂-COOH composites presented a typical ductile fracture behavior with large amounts of long and large strip-like cracks. When the content of SiO₂-COOH was 0.2 wt%, the SiO₂-COOH particles were uniformly dispersed over the entire body of the PA 6 matrix. The results from differential scanning calorimetry indicated that the melting point (T_m), degree of crystallinity (X_c), and crystallization temperatures (T_c) of PA 6/EBS/SiO₂-COOH composites were lower than the pure PA 6.     

Photoacoustic Spectra of Sm3+, Eu3+, Dy3+ Complexes

The complexes crystals of Sm(Ac)3.4H₂O, Eu(Ac)3.4H₂O and a new complex Dy2(Ac)(NO3)4.12H₂O were synthesized and their PA spectra were determined firstly. All their PA spectra absorptions are interpreted. The fluorescence properties of Sm³⁺, Eu³⁺, Dy³⁺ and the relaxation process models were studied by their PA spectra.     

CRYSTALLIZATION IN PARTIALLY MOLTEN ORIENTED BLENDS OF POLYCONDENSATES AS REVEALED BY X-RAY STUDIES*

Oriented fibers or films of binary polymer blends from polycondensates were investigated by two-dimensional (2D) wide-angle X-ray scattering (WAXS) during the finishing process of microfibrillar reinforced composite (MFC) preparation, that is, heating to a temperature between the melting temperatures of the two components, isothermal annealing, and subsequent cooling. It is shown that the crystallization behavior in such MFC from polycondensates depends not only on the blend composition, but also on thermal treatment conditions. Poly(ethylene terephthalate)/polyamide 12 (PET/PA12), poly(butylene terephthalate)/poly(ether ester) (PBT/PEE), and PET/PA6 (polyamide 6) composites were prepared in various compositions from the components. Materials were investigated using rotating anode and synchrotron X-ray source facilities. The effect of the annealing time on the expected isotropization of the lower melting component was studied in the PET/PA6 blend. It was found that PA6 isotropization took place after 2 h; shorter (up to 30 min) and longer (up to 8 h) melt annealing results in oriented crystallization due to different reasons. In PET/PA12 composites, the effect of PA12 transcrystallization with reorientation was confirmed for various blend compositions. The relative strength of the effect decreases with progressing bulk crystallization. Earlier presumed coexistence of isotropic and highly oriented crystallites of the same kind with drawn PBT/PEE blend was confirmed by WAXS from a synchrotron source.

     

An analytical solution for dynamic behavior of a beam–column frame with a tip body

This paper analyzes the vibration characteristics of a beam-column frame, typical examples of which are often found in optical pickup actuators of optical disc drives (ODDs) and many architectural structures. The dynamic behaviour of this beam structure is predicted by solving mathematically its vibration characteristics governed by beam configurations. For practical applications and simplicity in the analysis, the vibration analysis for the structure is limited to lateral and longitudinal directions of the beams. As a result, mode and modal frequencies are obtained from mathematical expressions. The accuracy of vibration characteristics, which is mathematically induced, is demonstrated by a finite element (FE) analysis. Finally, it is shown that mode shapes are modified by using design values with the mathematical expressions.     

HFC32/PVE的材料相容性实验研究

HFC32作为HCFC22理想可替代制冷工质之一,由于其和谐兼顾环保安全、节能减排以及市场转轨等诸方面要求,逐渐成为了替代应用研究的热点。本文基于目前国际上的制冷工质材料相容性研究方法,综合考虑HFC32和润滑油热物理性质,建立了一套针对性的材料相容性实验测试方法,实验研究了设定工况下HFC32及润滑油PVE与选定的压缩机密封材料PET和PA的相容性。结果表明:HFC32/PVE与PET和PA,在低水分浓度的润滑油测试条件下,具有较好的相容性。但在高水分浓度的润滑油及高温环境的测试下,PET材料的性能下降幅度要大于PA材料。     

输出功率-3dBm的射频发射前端在802.11g中的应用

A 2.4 GHz,direct-conversion RF transmitter front-end with an up converter and PA driver is fabricated in a 0.13μm CMOS process for the reliable transmission of 54 Mb/s OFDM signals.The front-end output power is -3 dBm while the corresponding EVM is -27 dB which is necessary for the 802.1 1g standard of EVM at-25 dB. With the adopted gain control strategy the output power changes from -14.3 to -3.7 dBm with every step 0.8 dB (20%) which covers the gain variation due to working temperature and process.A power detector indicates the output power and delivers a voltage to the baseband to control the output power.     

A fully integrated 2.4 GHz CMOS high power amplifier using parallel class A&B power amplifier and power-combining transformer for WiMAX application

A new structure integrated power amplifier with watt-level output power is presented in a standard 0.18 μm CMOS process for WiMAX applications. A parallel cascode class A&B power amplifier with optimized widths is proposed to increase linearity and efficiency simultaneously. A novel interleaved PCT power combiner is proposed for increasing output power that combines output current of two similar class A&B power amplifiers. Proposed interleaved transformer heightens coupling factor compared to typical transformer.     

公共广播系统的分区管理、传声器和扬声器

介绍了即将颁布的公共广播国家标准《公共广播系统工程技术规范》中关于系统分区的有关指引,并对这些指引进行了适当的讨论。介绍了关于广播传声器和广播扬声器的有关规定。     

Polyamide as an efficient sorbent for simultaneous interference-free determination of three Sudan dyes in saffron and urine using high-performance liquid chromatography-ultra violet detection北大核心CSCD

With polyamide( PA)as an efficient sorbent for solid phase extraction( SPE)of Sudan dyes II,III and Red 7B from saffron and urine,their determination by HPLC was performed. The optimum conditions for SPE were achieved using 7 mL methanol/water( 1:9,v/v,pH 7)as the washing solvent and 3 mL tetrahydrofu-ran for elution. Good clean-up and high( above 90%)recoveries were observed for all the analytes. The opti-mized mobile phase composition for HPLC analysis of these compounds was methanol-water( 70:30,v/v). The SPE parameters,such as the maximum loading capacity and breakthrough volume,were also determined for each analyte. The limits of detection( LODs),limits of quantification( LOQs),linear ranges and recoveries for the analytes were 4. 6-6. 6 μg/L,13. 0-19. 8 μg/L,13. 0-5 000 μg/L( r2> 0. 99)and 92. 5% -113. 4%,respec-tively. The precisions( RSDs)of the overall analytical procedure,estimated by five replicate measurements for Sudan II,III and Red 7B in saffron and urine samples were 2. 3%,1. 8% and 3. 6%,respectively. The developed method is simple and successful in the application to the determination of Sudan dyes in saffron and urine sam-ples with HPLC coupled with UV detection.     

自建光声超声双模态成像系统的肿瘤成像分析

现有B超成像可以提供基于声阻抗差异的组织解剖结构信息,而近年来研究发现,光声成像可以提供标记组织成分的分布和功能信息。本文基于商用B超仪和脉冲激光系统建立了光声超声双模态成像系统,实现了超声组织结构成像和光声生物功能的同时成像。首先基于血红蛋白在某些波段的较强吸光性,实现了肿瘤内部组织血管灌注图像;其次用链接有靶向抗体的纳米颗粒作为靶向光声造影剂,对恶性肿瘤边缘和内部的血管以及血管附近的肿瘤组织进行了成像。最终,通过超声和光声的融合图像提供的肿瘤结构信息与光声图像提供的肿瘤功能信息,可以准确识别肿瘤组织。