扩声系统调整与声学测试技术

介绍了扩声系统调整的概要与扩声系统声学测试方法的要点,主要从扩声系统组成、各部件调整要点、遵循的原则,扩声系统声学测试技术所遵从的标准、方法、数据处理方法等方面进行了介绍,鉴于目前一些从业人士对扩声系统声学测试技术了解不甚全面,依据GB/T 4959—2011厅堂扩声测量方法,详细介绍了各种测量内容的具体方法与数据处理,并给出了相关的电子表格(Execl)数据处理计算表。     

BER Modified Decode-and-Forward Protocol for OFDM-Based Linear Multihop Networks

In orthogonal frequency division multiplexing （OFDM） based multihop communications, the conventional decodeand-forward （DF） relay scheme severely suffers from the error propagation problem. This drawback is serious in multihop networks as errors made by any relay node may fail the decoder at the destination in great chance. In this paper, we propose a bit error rate （BER） modified DF protocol （BMDF） which can be applied to systems where error correction channel coding and M-ary modulation are used. By modeling all links except the last one as a binary symmetric channel （BSC）, we derive a log likelihood ratio （LLR） modification function relying only on the accumulated BER of all previous links to be applied to the output of the soft demapper. Furthermore, to reduce the computational complexity and signaling overhead, the modification function is simplified from its original exponential expression and less BERs are delivered between nodes by making successive subcarriers share the same BER. In addition, for situations where the channel state information （CSI） of forward link is available, the proposed BMDF can be further enhanced by combining with subcarrier pairing （SP） and power allocation （PA）, where a sorted-channel gain SP scheme and a greedy PA algorithm are proposed. The simulation results verify thesignificant performance improvement to the conventional DF.     

Electrically switchable reflection holograms formed using two-photon photopolymerization

Two-photon holographic photopolymerization was used to form switchable Bragg gratings composed of layers of phase-separated liquid-crystal (LC) domains interspersed with cured, crosslinked polymer. These holographic polymer-dispersed liquid crystals form a periodic structure which diffracts red light due to nanostructured planes ∼250 nm in spacing. These structures were formed by interfering two 90-fs pulses coherently upon a reactive syrup consisting of acrylate monomer, liquid crystal, and a two-photon dye. The large two-photon cross-section allows excitation of the two-photon dye that results in electron transfer between this dye and the monomer. Diffraction efficiencies of approximately 10% were obtained, which can be modulated using an electric field applied across the film. Switching speeds below 1 ms were observed due in part to the small size of the LC domains. Received: 10 April 2001 / Accepted: 1 July 2001 / Published online: 2 October 2001     

Fractionated crystallization of compatibilized LDPE/PA6 blends

The paper presents differential scanning calorimetry and electron microscopy of the fractionated crystallization and polydispersity of the dispersed PA6 phase in compatibilized LDPE/PA6 75/25 w/w blends. The compatibilizers used were (i) an acrylic acid functionalized polyethylene, Escor 5001 (EAA); (ii) an ethylene-glycidylmethacrylate copolymer, Lotader GMA AX8840 (EGMA); (iii) a polystyrene-poly(ethylene-butylene)-polystyrene triblock copolymer comprising 2 wt.% maleic anhydride grafts, Kraton FG 1901X (SEBS-g-MA). The compatibilizer SEBS-g-MA has the strongest reduction effect upon the size of PA-6 droplets. Its implementation provides the best fractionated crystallization. The fractionated crystallization has not been observed for the blend compatibilized with EGMA. The results show that the degree of compatibilization could be evaluated qualitatively by the progress of the fractionated crystallization. So, the three compatibilizers could be rated according to their effectiveness as follows: SEBS-g-MA > EAA > EGMA. The self-nucleation experiments have demonstrated that the lack of active nuclei in the finely dispersed PA6 droplets is the determining factor for the fractionated crystallization at high supercooling, and not the considered absolute particle size. The measurement of the Vickers microhardness of the compatibilized blends confirms that the compatibilizing activity of SEBS-g-MA and EAA is stronger than that of EGMA.     

大电流型功率放大器PA04及其应用

PA04是美国APEX公司生产的一种大电流型功率放大器 ,它具有工作电压高、输出电流大、转换速率高、失真低等特点。文中结合该器件的管脚特性及典型应用 ,详细介绍了PA04的工作原理以及外围器件选取时应注意的一些问题     

Mie散射研究聚合物合金相结构的形成及相尺寸分布

本文应用Mie散射理论研究了聚丙烯 /尼龙 1 0 1 0合金的相结构与形态 ,计算了相尺寸分布。其结果与电子显微镜及Rayleigh散射结果进行了比较。     

PA序列部分和完全收敛性的进一步探讨

通过讨论矩的存在性与部分和尾概率级数收敛性的关系,给出了PA序列部分和的完全收敛性,获得了PA序列与独立序列类似的强极限性质.     

Linex损失及PA样本下单边截断型分布族参数函数的EB估计

在Linex损失函数下,运用同分布PA样本密度函数的核估计方法,构造了一类单边截断型分布族参数函数的EB估计,并建立了它的收敛速度.在一定条件下,证明了这个收敛速度可充分接近1.     

尼龙6/氯化钾复合材料的结晶与性能

通过熔融共混法制备了不同KCl含量下的尼龙6(PA6)/KCl复合材料,采用示差扫描量热仪(DSC)、流变仪、红外光谱(IR)、电子拉伸机等研究了KCl含量对PA6/KCl复合材料结晶行为、流变性能及力学性能的影响,并研究了其受限机制.力学性能研究结果表明,随着KCl含量的增加,PA6/KCl复合材料拉伸强度和冲击强度呈现出先增大后减小的趋势,在KCl含量为3 phr时,复合材料拉伸强度和冲击强度分别达到最大值82.67 MPa和7.34 k J/m~2,较纯PA6分别增加了10.8%和34.68%,动态力学性能测量结果表明,在测量温度范围内,复合材料的储能模量均高于纯PA6,在25℃体系储能模量(G')随KCl含量的增加而增大,复合体系抵抗弯曲变形能力增加,而结晶行为研究结果表明,增加KCl的含量,PA6/KCl复合材料的成核温度、晶体生长温度、熔融温度及玻璃化转变温度均向低温方向移动,成核密度和成核速率也逐渐减小,结晶能力下降,结晶度减小,结晶度由原来25.30%变为19.34%,而结晶诱导时间逐渐增加.流变性能研究结果表明,随着KCl含量的增加,复合体系的零剪切黏度逐渐增加,且所有的体系均呈现出假塑性流体行为,剪切变稀现象越来越明显,特征松弛时间τ_1、τ_2和τ_3逐渐增加,复合体系的松弛机制发生变化.     

An overview of lipid membrane supported by colloidal particles

In recent years, original hybrid assemblies composed of a particle core surrounded by a lipid shell emerged as promising entities for various biotechnological applications. Their broadened bio-potentialities, ranging from model membrane systems or biomolecule screening supports, to substance delivery reservoirs or therapeutic vectors, are furthered by their versatility of composition due to the possible wide variation in the particle nature and size, as well as in the lipid formulation. The synthesis, the characteristics, and the uses of these Lipid/Particle assemblies encountered in the literature so far are reviewed, and classified according to the spherical core size in order to highlight general trends. Moreover, several criteria are particularly discussed: i) the interactions involved between the particles and the lipids, and implicitly the assembly elaboration mechanism, ii) the most suited techniques for an accurate characterization of the entities from structural and physicochemical points of view, and iii) the remarkable properties of the solid-supported lipid membrane obtained.