Development and application of an analytical protocol for evaluation of treatment processes for landfill leachates. II. Evaluation of leachate treatment efficiency of different steps in a constructed pilot plant

Different methods for treatment of leachate from a municipal solid waste (MSW) landfill were tested in a pilot plant. Raw leachate was pre-treated with aeration and sedimentation, followed by several parallel individual steps such as bioremediation, chemical oxidation, ozonation, and geo-bed filters. The efficiency of different treatment steps was evaluated according to one previously developed protocol, which includes measurements of several parameters such as conductivity, pH, nutrients, chloride, metals, organic compounds, and acute toxicity before and after a treatment step. The treatment steps which showed the highest efficiency towards organic pollutants in leachate were ozone treatment and chemical oxidation. The use of an adsorption filter, a geo-bed with a mixture of peat and bottom ash with ca 10% remaining carbon, also had good effects. A combination of pre-treatment and a geo-bed filter with peat and carbon ash gave the best overall treatment results when water-quality parameters such as total organic carbon and ammonia-nitrogen were also considered.     

自动顶空固相微萃取气相色谱法同步分析水中17种有机物

采用自动顶空固相微萃取(HS-SPME)技术与气相色谱联用同步分析水中1,4-二氯苯、1,2-二氯苯、1,3,5-三氯苯、1,2,4-三氯苯、1,2,3-三氯苯、六氯苯、硝基苯、对硝基甲苯、α-666、β-666、γ-666、δ-666、七氯、ρ,ρ′-DDE、ρ,ρ′-DDD、o,ρ′-DDT、ρ,ρ′-DDT17种有机物。方法的最低检出浓度为0.001~0.044μg/L,线性相关系数均大于0.999,相对标准偏差为1.4%~8.7%,加标回收率在81.3%~122.9%之间。     

Solvent flux behavior and rejection characteristics of hydrophilic and hydrophobic mesoporous and microporous TiO2 and ZrO2 membranes

This paper describes solvent flux and rejection behavior of different hydrophilic TiO₂ membranes and a hydrophobic ZrO₂ membrane. Solvents and solutes used range from polar to non-polar. Additionally, the temperature effect on permeability and rejection of solutes through these membranes was examined.     

Differences in porous characteristics of styrenic monoliths prepared by controlled thermal polymerization in molds of varying dimensions

Nitroxide‐mediated polymerization was used as a model system for preparing styrenic monolithic materials with significant mesopore contents in different mold formats, with the aim of assessing the validity of pore characterization of capillary monoliths by analysis of parallel bulk polymerized precursor solution. Capillary monoliths were prepared in 250 μm id fused silica tubes (quadruplicate samples, in total 17 m), and the batch polymerizations were carried out in parallel in 100 μL microvials and regular 2 mL glass vials, both in quintuplicate. The monoliths recovered from the molds were characterized for their meso‐ and macroporous properties by nitrogen sorptiometry (three repeated runs on each sample), followed by a single analysis by mercury intrusion porosimetry. A total of 14 monolith samples were thus analyzed. A Grubbs' test identified one regular vial sample as an outlier in the sorptiometric surface area measurements, and data from this sample were consequently excluded from the pore size calculations, which are based on the same nitrogen sorption data, and also from the mercury intrusion data set. The remaining data were subjected to single factor analyses of variance analyses to test if the porous properties of the capillary monoliths were different from those of the bulk monoliths prepared in parallel. Significant differences were found between all three formats both in their meso‐ and macroporous properties. When the dimension was shrunk from conventional vial to capillary size, the specific surface area decreased from 52.2±4.7 to 34.6±1.7 m²/g. This decrease in specific surface area was accompanied by a significant shift in median diameter of the through‐pores, from 310±3.9 to 544±13 nm. None of these differences were obvious from the scanning electron micrographs that were acquired for each sample type. The common practice of determining the mesopore characteristics from analysis of samples prepared by parallel bulk polymerization and looking for changes in the macropore structure by visual assessment of SEMs are therefore both rather questionable, at least for monoliths of the kind used in this study.     

Rational Design of a Near-infrared Fluorescent Material with High Solid-state Efficiency,Aggregation-induced Emission and Live Cell Imaging Property

Near-infrared(NIR) fluorescent materials with high photoluminescent quantum yields(PLQYs) have wide application prospects. Therefore, we design and synthesize a D-A type NIR organic molecule, TPATHCNE, in which triphenylamine and thiophene are utilized as the donors and fumaronitrile is applied as the acceptor. We systematically investigate its molecular structure and photophysical property. TPATHCNE shows high T_gof 110℃ and T_d of 385℃ and displays an aggregation-induced emission(AIE) property. A narrow optical bandgap of 1.65 eV is obtained. The non-doped film of TPATHCNE exhibits a high PLQY of 40.3% with an emission peak at 732 nm, which is among the best values of NIR emitters. When TPATHCNE is applied in organic light-emitting diode(OLED), the electroluminescent peak is located at 716 nm with a maximum external quantum efficiency of 0.83%. With the potential in cell imaging, the polystyrene maleic anhydride(PMSA) modified TPATHCNE nanoparticles(NPs) emit strong fluorescence when labeling HeLa cancer cells, suggesting that TPATHCNE can be used as a fluorescent carrier for specific staining or drug delivery for cellular imaging. TPATHCNE NPs fabricated by bovine serum protein(BSA) are cultivated with mononuclear yeast cells, and the intense intracellular red fluorescence indicates that it can be adopted as a specific stain for imaging.     

Removal of Anionic Dyes from Aqueous Solution with Layered Cationic Aluminum Oxyhydroxide

It is highly desired yet challenged to find an adsorbent with low cost and excellent performance in the removal of organic dyes from aqueous solution. Here we reported that a layered cationic aluminum oxyhydroxide material hydrothermally synthesized from the low-cost source materials of AlCl₃∙6H₂O, CaO and H₂O, known as JU-111, can meet such criterion in removing methyl orange(MO) and Congo red(CR). JU-111 shows fast adsorption kinetics[especially for CR(15 s)] and high adsorption capacity(MO:>1000 mg/g; CR:>2900 mg/g), surpassing most of the reported adsorbents. Comprehensive characterizations of the adsorption process of MO and CR revealed that both adsorptions were achieved via the anion exchange process. The characteristics of extremely low cost and excellent performance render JU-111 great potential in the practical applications in the removal of anionic dyes.     

Ultrahigh Loading Copper Single Atom Catalyst for Palladium-free Wacker Oxidation

Wacker oxidation is an industry-adopted process to transform olefins into value-added epoxides and carbonyls. However, traditional Wacker oxidation involves the use of homogeneous palladium and copper catalysts for the olefin addition and reductive elimination. Here, we demonstrated an ultrahigh loading Cu single atom catalyst(14% Cu, mass fraction) for the palladium-free Wacker oxidation of 4-vinylanisole into the corresponding ketone with N-methylhydroxylamine hydrochloride as an additive under mild conditions. Mechanistic studies by ¹⁸O and deuterium isotope labelling revealed a hydrogen shift mechanism in this palladium-free process using N-methylhydroxylamine hydrochloride as the oxygen source. The reaction scope can be further extended to Kucherov oxidation. Our study paves the way to replace noble metal catalysts in the traditional homogeneous processes with single atom catalysts.