双电极对双脉冲激光器结构分析

本文对双电极对双脉冲激光器的谐振腔结构进行了分析,结果表明采用双非稳腔和增大反射镜的曲率半径可分别获得单纵模和基横模输出。为使输出能量稳定,则双电极对的间距有一最小值的限制。     

高功率板条固体激光器研究的进展

本文对高功率板条固体激光器研究的进展和应用前景作了综合评述。结合作者部分工作,对板条激光器的热效应、聚光器和光学谐振腔等关键问题和技术进行了物理分析。     

Coupling Losses for Resonators with Unequal Apertures for Extended Fresnel Numbers

Coupling losses have been calculated for laser resonators with unequal apertures and extended Fresnel Numbers. This was done using both, diffraction theory and a simple linear model.A close form expression was derived to calculate coupling losses with reasonable accuracies for a limited range of paramters. This should help in the preliminary design of hole coupling laser resonators.     

Rare-earth-enabled universal solders for microelectromechanical systems and optical packaging

In packaging of microelectromechanical systems (MEMS), optical, and electronic devices, there is a need to directly bond a wide variety of inorganic materials, such as oxides, nitrides, and semiconductors. Such applications involve hermetic-sealing components, three-dimensional MEMS assembly components as well as active semiconductor or optical components, dielectric layers, diffusion barriers, waveguides, and heat sinks. These materials are known to be very difficult to wet and bond with low melting-point solders. New Sn-Ag- or Au-Sn-based universal solders doped with a small amount of rare-earth (RE) elements have been developed, which now allow direct and powerful bonding onto the surfaces of various MEMS, optical, or electronic device materials. The microstructure, interface properties, and mechanical behavior of the bonds as well as the potential packaging applications of these new solder materials for MEMS and optical fiber devices are described. Various packaging-related structural, thermal, or electrical issues in MEMS are also discussed.     

分析非轴对称腔的复光线数值迭代法

将像散光束的复光线表示法用于分析非轴对称腔，并对有复杂像散的折迭腔作了数值迭代计算以说明方法的应用．     

高功率固体激光器

本文详细讨论了设计高平均功率固体激光器的有关问题,包括激光材料性质、棒状和板条状几何结构,聚光器和光学谐振腔等。分析表明,板条状几何结构固体激光器提供了达到千瓦级功率水平同时又保持良好光束质量的可能性。     

PCR芯片和生化微分析系统

介绍了PCR微芯片的最新研究进展,给出了不同结构的PCR芯片设计原理以及特点,介绍由PCR芯片为主要单元的集成微全分析系统的相关研究,同时简要介绍了对PCR的仿真模拟等。     

A DC excited waveguide multibeam CO2 laser using high frequency pre-ionization technique

High power industrial multibeam CO₂ lasers consist of a large number of closely packed parallel glass discharge tubes sharing a common plane parallel resonator. Every discharge tube forms an independent resonator. When discharge tubes of smaller diameter are used and the Fresnel numberN ≪ 1 for all resonators, they operate in waveguide mode. Waveguide modes have excellent discrimination of higher order modes. A DC excited waveguide multibeam CO₂ laser is reported having six glass discharge tubes. Simultaneous excitation of DC discharge in all sections is achieved by producing pre-ionization using an auxiliary high frequency pulsed discharge along with its other advantages. Maximum 170 W output power is obtained with all beams operating in EH₁₁ waveguide mode. The specific power of 28 W/m is much higher as compared to similar AC excited waveguide multibeam CO₂ lasers. Theoretical analysis shows that all resonators of this laser will support only EH₁₁ mode. This laser is successfully used for woodcutting     

Effect of Pressure on Fluid Damping in MEMS Torsional Resonators with Flow Ranging from Continuum to Molecular Regime

High quality factor of dynamic structures at micro and nano scale is exploited in various applications of micro electro-mechanical systems (MEMS) and nano electro-mechanical system. The quality factor of such devices can be very high in vacuum. However, when vacuum is not desirable or not possible, the tiny structures must vibrate in air or some other gas at pressure levels that may vary from atmospheric to low vacuum. The interaction of the surrounding fluid with the vibrating structure leads to dissipation, thus bringing down the quality factor. Depending on the ambient fluid pressure or the gap between the vibrating and the fixed structure, the fluid motion can range from continuum flow to molecular flow giving a wide range of dissipation. The relevant fluid flow characteristics are determined by the Knudsen number which is the ratio of the mean free path of the gas molecule to the characteristic flow length of the device. This number is very small for continuum flow and reasonably big for molecular flow. In this paper, we study the effect of fluid pressure on the quality factor by carrying out experiments on a MEMS device that consists of a double gimbaled torsional resonator. Such devices are commonly used in optical cross-connects and switches. We only vary fluid pressure to make the Knudsen number go through the entire range of continuum flow, slip flow, transition flow, and molecular flow. We experimentally determine the quality factor of the torsional resonator at different air pressures ranging from 760 Torr to 0.001 Torr. The variation of this pressure over six orders of magnitude ensures required rarefaction to range over all flow conditions. Finally, we get the variation of quality factor with pressure. The result indicates that the quality factor, Q, follows a power law, Q ∝P ^–r , with different values of the exponent r in different flow regimes. In the second part of the paper, we propose the use of effective viscosity for considering velocity slip conditions in solving Navier–Stokes equation numerically. This concept is validated with analytical results for a simple case and then compared with the experimental results presented in this paper. The study shows that the effective viscosity concept can be used effectively even for the molecular regime if the air-gap to length ratio is sufficiently small (h ₀/L<0.01). As this ratio increases, the range of validity decreases.     

微电子机械系统

本文对国外微电子机械系统的研究现况作了评述，介绍了ＭＥＭＳ的主要技术和它的应用情况，对国外的一些主要研究机构的情况进行了分析，最后就我国ＭＥＭＳ的发展提出了一些建议。