Radiative lifetimes in Ce I and Ce II

New radiative lifetime measurements based on time-resolved laser-induced fluorescence techniques are reported for 18 even-parity levels belonging to the 4f5d^26p and 4f ²5d ² configurations of Ce I and 6 even-parity levels belonging to the 5d^26s, 4f5d6p, and 4f6s6p configurations of Ce II. Free neutral and singly ionized cerium atoms were produced by laser ablation. The Ce I and Ce II levels range in energy from 26 545 to 29 102 cm^-1, and 42 573 to 48 152 cm^-1, respectively. Received 25 September 2002 Published online 4 March 2003     

Cu~+、Ag~+、Au~+与乙硫醇的气相化学反应

利用激光溅射 分子束的技术 ,结合反射飞行时间质谱计 ,研究了Cu+、Ag+、Au+与乙硫醇的气相化学反应。结果显示这三种金属离子与 (CH3 CH2 SH) n 反应形成一系列团簇离子M+(CH3 CH2 SH) n,且团簇离子尺寸不一样。Ag+、Au+与乙硫醇的反应还生成了 (CH3 CH2 SH) +n ,由此推测Cu+、Ag+、Au+与乙硫醇团簇的反应存在两种通道 ,一种通道是生成M+(CH3 CH2 SH) n,另一种是生成 (CH3 CH2 SH) +n 。Cu+、Au+与乙硫醇的反应还生成了M+(H2 S) (M =Cu、Au) ,但是实验中没有观察到Ag+(H2 S) ,理论计算表明Ag+(H2 S)很不稳定。另外 ,分析产物离子M+(CH3 CH2 SH) n 的强度发现 ,n =1～ 2之间存在明显的强度突变现象     

Hybrid numerical—experimental approach for investigation of dynamics of microcantilever relay system

The time average holography measurements of the vibrating microelectromechanical switch (MEMS) were performed in this study. Experimental measurement results exhibit good agreement with computer generated holographic interferogram analysis. The validation of experimental investigations versus numerical analysis provides the necessary background to analyze the dynamical characteristics of micromechanical systems in virtual numerical environments. Direct application of fringe counting techniques for reconstruction of motion from time average holograms cannot be straightforward if the analyzed micromechanical systems contain motion limiters. Modifications of a classical time average holographic technique enable qualitative analysis of MEMS and can be applied for investigation of dynamical properties of much broader classes of MEMS systems.     

Spectral features of laser induced plasma from YBa2Cu3O7 and GdBa2Cu3O7 highT c superconductors

Laser induced plasma emission spectra from highT _c superconducting samples of YBa₂Cu₃O₇ and GdBa₂Cu₃O₇ obtained with 1.06μm radiation from a Q switched Nd:YAG laser beam has been analysed. The results clearly show the presence of diatomic oxides in addition to ionized species of the constituent metals in the plasma thus produced.     

Effects of aldehyde or dipyrromethane substituents on the reaction course leading to meso-substituted porphyrins

To better understand the effects of diverse substituents on reactions leading to porphyrins, pyrrole+aldehyde condensations and related reactions of dipyrromethanes were examined. The course of pyrrole+aldehyde condensations was investigated by monitoring the yield of porphyrin (by UV-Vis spectroscopy), reaction of aldehyde (by TLC), and changes in the composition of oligomers (by laser desorption mass spectrometry). Reaction reversibility was examined via exchange experiments. Reversibility of reactions leading to porphyrin was further probed with studies of dipyrromethanes. The reaction course was found to depend on the nature of the substituent and the acid catalyst. Alkyl or electron-donating substituents displayed levels of reversibility (exchange/scrambling) on par or greater than that of the phenyl substituent, whereas electron-withdrawing or sterically bulky substituents exhibited little to no reversibility. The results obtained provide insight into the electronic and steric effects of different substituents and should facilitate the design of synthetic plans for preparing porphyrinic macrocycles.     

Strain hardening of polycarbonate in the glassy state: Influence of temperature and molecular weight

This study is concerned with the temperature and molecular weight dependence of the strain-hardening behavior of polycarbonate. It is shown that the strain-hardening modulus reduces with increasing temperature and decreasing molecular weight. This result is interpreted in terms of temperature accelerated relaxation of the entanglement network. Moreover, it is shown that frozen-in orientations, induced by homogeneous deformations above the glass transition temperature, lead to anisotropic yield behavior that can be fully rationalized (and modelled) in terms of a superimposed stress contribution of the prestrained network. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2041–2049, 2004     

ns脉冲激光对K9玻璃的破坏实验

 采用高速PIN光电探测器和高带宽的数字存储示波器，实时检测透射光脉冲和散射光脉冲的变化特征，并将之用作材料破坏的光学判据，测量得到K9玻璃在1.06μm纳秒脉冲激光作用下的能量损伤阈值约18mJ，相应的能量密度阈值为1.0kJ/cm²。通过分析透射光脉冲和散射光脉冲的特征，给出了材料的破坏时刻，并推断出K9玻璃所能承受的极限光强为10¹⁵W/m²。研究了能量透过率与泵浦能量的关系，并初步探讨了透明材料的破坏机理。结果表明：在多纵模激光的作用下，透明光学材料破坏是电离击穿与自聚焦效应综合作用的结果。     

19.6nm波长类氖锗X光激光光源理论模拟

 波长19.6nm的类氖锗X光激光适合作为诊断激光等离子体界面不稳定性的光源。用经过实验检验的系列程序对预-主短脉冲驱动类氖锗进行了系统的优化设计和理论分析。采用2%~3%的预脉冲强度，6~8ns的预-主脉冲时间间隔，在4×10¹³W/cm²功率密度驱动下, 波长19.6nm增益区的宽度可以超过60μm，增益区的维持时间可以达到90ps。对于16mm长的平板靶，增益系数可达11.8/cm；弯曲靶增益系数可达13.3/cm；单靶小增益长度积可达21.3，单靶就可以获得饱和增益。采用双靶对接，其小讯号增益可达38.4，可以获得深度饱和增益，能满足应用演示所需的X光激光光源。     

用于激光推进的高功率激光器的选择

 从激光推进的要求出发，阐述了用于激光推进的高功率激光器的选择原则，即激光器必须满足：（1）高的平均功率和峰值功率；（2）高的单脉冲能量；（3）高的重复频率；（4）优良的大气传输特性。主要分析了目前YAG固体激光器、自由电子激光器和TEA脉冲CO₂激光器的特点，通过上述4个方面性能的比较，认为在目前水平下，TEA脉冲CO₂激光器是进行激光推进的首选强激光源，其优点表现在：功率可达10kW量级，单脉冲能量可达0.5~1kJ，重复频率为20~40Hz；激光波长处于大气传输窗口，对大气变化不敏感；工作物质快速流动，不存在热透镜效应和破坏阈值；相关光学元件易于制造；光束质量较好；运行成本低。     

In-time motion adjustment in laser cladding manufacturing process for improving dimensional accuracy and surface finish of the formed part

This paper presents in-time motion adjustment in laser cladding manufacturing process as a means to improve dimensional accuracy and surface finish of the built part. Defects occurring during laser cladding degrade the part quality such as dimensional accuracy and surface finish. In this paper, in-time motion adjustment strategy was presented to remedy and eliminate defects occurring during laser cladding to improve the dimensional accuracy and surface finish. Based on the relationship between the motion of laser head relative to the growing part and other parameters in effects on clad profile, the laser traverse speed, stand-off distance and laser approach orientation to the existing clad layer were adjusted by instructions from a close-loop control system in real time to remedy and eliminate defects. The results of the experiments verified the effects of in-time motion adjustment on dimensional accuracy and surface finish.