Growth and characterization of hot-wall epitaxial CdTe on (111) HgCdTe and CdZnTe substrates

Thin CdTe films were deposited by hot-wall epitaxy (HWE) on (111) HgCdTe and CdZnTe substrates at temperatures from about 140 to 335°C. X-ray rocking curves were used to show that crystal quality of the CdTe (111)B films improved as substrate temperature increased from 140 to about 250°C. Rocking curve values for full width at half maximum (FWHM) decreased from 2–4 degrees at 140–150°C to less than 100 arc-s at 250°C, and a FWHM of 59 arc-s was the lowest value observed near 250°C. The FWHM of the HWE CdTe was found to be insensitive to growth rate below about 400Å/min, but increased to four degrees at 1250Å/min. X-ray diffraction confirmed that films grown on the B-face at higher temperatures were epitaxial, but contained a significant volume fraction, 35% to 50%, of rotational in-plane twins. Electron microscopy confirmed a coarse twin density, and photoluminescence spectra showed an absence of excitonic emission in the HWE films. Simultaneous growth on two (111) HgCdTe substrates with different surface polarities between 230°C and 335°C showed that deposition rate on the A-face decreased relative to that on the B-face as temperature increased. Films grown on the B-face exhibited better surface morphologies than those grown on the A-face.     

Outflow refreshment angiography: A bright blood, bright static tissue technique

A new “bright blood” strategy, outflow refreshment imaging, is introduced in which a number of overlapping slices are excited in rapid succession. Flowing spins that refresh each overlapped slice portion contribute a bright signal. Additionally, static tissue in each non-overlapped slice portion also yields a bright signal. However, the flow/static contrast is comparable to that produced in inflow refreshment images, and angiograms can be generated by conventional maximum intensity projection processing. The dual ability to visualize angiograms and static tissue images is a major benefit of the strategy. Computer simulations of flow sensitivities and in vivo results are presented which compare the outflow and inflow refreshment imaging strategies.     

空气中烧成的镍导体及其应用

将空气中烧成的镍导体用于散热制冷片制作工艺中，可降低成本，提高合格率。通过实验得到的最佳值为：镍导体中４号玻璃（ＳｉＯ２＞３０，Ｂ２Ｏ３＞１０，ＰｂＯ＜５５，ＴｉＯ２少许）的含量４．５％，化学镀镍时间５０ｍｉｎ，方阻４７．５ｍΩ／□，附着力８．１Ｎ／ｍｍ２。     

热处理WO3电变色膜稳定性研究

采用电子束蒸发淀积ＷＯ３薄膜。根据已有的ＷＯ３薄膜脱水过程结论而选择适当温度对薄膜进行退火处理。在大量含水的和不含水的两类Ｌｉ＾＋电解质中进行比较性着色和消色循环实验，表明在２９０℃以下热退火处理能明显增加ＷＯ３薄膜在含水 电解质中的循环寿命。     

钛酸铅系薄膜的热释电性能及其应用

叙述了钛酸铅系薄膜的热释电原理，介绍了国际上近几年钛酸铅系薄膜材料、制备工艺及热释电性能，并与块状陶瓷材料进行了比较，分析表明钛酸铅系薄膜具有优良的热释电性能及可观的应用前景。     

BRD96N光调制吸收增强现象的实验研究

通过光谱响应特性实验和记录／读出图像实验，研究了基因变异型细菌视紫红质（BR_D96N）分子膜对单色光的光调制特性.发现BR_D96N分子膜在550nm—600nm范围内对调制光有吸收增强的现象，且对此范围内不同波长的单色光其调制程度有差异.利用曲线拟和方法发现550nm—600nm吸收增强的变化过程分为快过程和慢过程，其对应的时间常数分别为30s和5min.利用强度调制器的吸收强度与图像灰度之间的关系，分析了560nm—600nm范围内出现图像反转的实验现象. 关键词： 细菌视紫红质D96N分子膜 光谱响应 吸收增强现象 图像反转现象     

Organic Electroluminescent Thin Film Using 8—hydroxyquinoline Zinc as Emitting Layer

Organic electroluminescent thin film using Znq2(Znq2) as the emitting layer material with structure of glass/ITO/Znq2/Al(cell) was fabricated.The V-I curve ,V-B curve and electroluminescent spectra of the cell were measured.Meanwhile the fluorescent spectra, excited spectra and absorption spectra of Znq2 with power and film states were also measured.     

Dynamic response of permalloy/Cu/Co magnetoresistive sandwiches

The dynamic response of trilayer magnetoresistive permalloy/Cu/Co films was studied by high-frequency permeability spectra measurements. The resonance frequency is shown to depend on the interlayer copper thickness. This dependence is related to exchange coupling between permalloy and cobalt and the interaction field is estimated using the Landau–Lifschitz–Gilbert model.     

非晶硅薄膜的低温快速晶化及其结构分析

在镀铝的廉价玻璃衬底上高速沉积的非晶硅薄膜在不同的温度下退火10min.退火温度为500℃时,薄膜表面形成了硅铝的混合相,非晶硅薄膜开始呈现了晶化现象 退火温度为550℃时,大部分(约80%)的非晶硅晶化为多晶硅,平均晶粒尺寸为500nm 退火温度为600℃时,几乎所有的非晶硅都转化为多晶硅,其平均晶粒尺寸约为15μm.