基于两层均匀媒质的GPEN SAR地下目标成像方法及其性能分析

地表穿透合成孔径雷达(Ground PENetration SAR,GPEN SAR)为了探测掩埋在地下的目标,通常工作在多层媒质的环境中。传统成像模型是建立在同一均匀媒质的假设上,不再适合于GPEN SAR的实际情况。本文首先建立了两层分区均匀媒质中的成像模型,然后利用后向投影(BP)算法定量分析了成像几何参数、土壤参数等对成像的影响,进而提出了一种修正的后向投影(MBP)算法。MBP算法不仅能够校正两层分区均匀媒质对成像定位的影响,还能估计目标的掩埋深度,提供目标三维位置坐标。仿真结果验证了MBP算法在不同信噪比环境下,对多目标的三维定位精度能满足实际的需要。     

相关条件下基于N-P准则的分布式检测理论研究

本文针对并行网络、二元局部判决的情况,研究了在相关条件下基于N-P准则的分布式检测融合算法,给出了在联合概率密度已知和未知两种情况下的最优融合规则的理论推导及相应的解决方案,并在实验仿真的基础上,得到了部分有益的结论。     

质量控制图系统的实现及在SMT中的应用

本文将控制图理论与计算机技术相结合,开发了质量控制图系统.介绍了该系统的设计方案和关键技术问题,并以电子产品制造中监控SMT机的焊膏厚度为例说明了系统的应用.     

2.4GHz动态CMOS分频器的设计

对现阶段的主流高速CMOS分频器进行分析和比较,在此基础上设计一种采用TSPC(truesingle phase clock)和E-TSPC(extended TSPC)技术的前置双模分频器电路.该分频器大大提高了工作频率,采用0.6μm CMOS工艺参数进行仿真的结果表明,在5V电源电压下,最高频率达到3GHz,功耗仅为8mW.     

有线电视工程建设流程再造设计

从理论与实际工作相结合的角度出发,以淄博广电青鸟公司为研究对象,对有线电视网络工程建设流程的现状、存在的问题和原因进行细致深入分析,然后按照提出的再造方案的设计原则,设计了工程建设流程的再造方案,并对新旧流程进行比较。     

焊膏印刷工艺参数的选择与优化

表面贴装工艺流程的关键工序之一就是焊膏印刷,其工艺控制的好坏直接影响着装配的线路板的质量。通过对印刷工艺参数的分析,利用试验设计的方法来找出关键工艺参数,并加以优化设定,从而为控制工序参数奠定基础。     

积层板的制造方法

概述了积层板的开发背景、制造工艺和最近的开发动向。     

从RC5到RC6

论文详细描述并分析了从RC5到RC6的演化设计过程,在详细研究了RC6性能的同时,指出了应该如何从一个旧的密码设计出好的新密码。最后对RC6和Rijndael作了一些比较,指出各自在性能上的优缺点。     

On the effects of the packet size distribution on the packet loss process

Real-time multimedia applications have to use forward error correction (FEC) anderror concealment techniques to cope with losses in today’s best-effort Internet. The efficiency of these solutions is known however to depend on the correlation between losses in the media stream. In this paper we investigate how the packet size distribution affects the packet loss process, that is, the distribution of the number of lost packets in a block, the related FEC performance and the average loss run length. We present mathematical models for the loss process of the MMPP+M/D/1/K and the MMPP+M/M/1/K queues; we validate the models via simulations, and compare the results to simulation results with an MPEG-4 coded video trace. We conclude that the deterministic packet size distribution (PSD) not only results in lower stationary loss probability than the exponential one, but also gives a less correlated loss process, both at a particular average link load and at a particular stationary loss probability as seen by the media stream.Our results show that for applications that can only measure the packet loss probability, the effects of the PSD on FEC performance are higher in access networks, where a single multimedia stream might affect the multiplexing behavior. Our results show that the effects of the PSD on FEC performance are higher in access networks, where a single multimedia stream might affect the multiplexing behavior and thus can improve the queuing performance by decreasing the variance of its PSD.     

等离子体刻蚀工艺控制模型分析

讨论了主因素分析法以及神经网络法在等离子体刻蚀工艺中的应用.结果表明主元素分析法可以实现对数据的压缩,而神经网络算法则显示出比传统的统计过程控制算法更好的准确性.