HER磁镜上硬X射线和热电子测量

一、引言 磁镜运行中,为了要知道它在电子回旋共振加热(ECRH)下形成热电子的参数,我们测量了硬X射线能谱、硬X射线发射的时间特性、不同磁场强度下形成热电子环的位置、以及热电子的脉冲幅度分布等。 HER是中国科学院等离子体物理研究所简单型磁镜装置,它的几何尺寸是,真空室长     

Influence of chemistry and hot rolling conditions on high permeability non-grain oriented silicon steel

This paper discusses the influence of chemical composition on the final electromagnetic properties in higher permeability material. Furthermore, the effect of the hot rolling practice and the end of austenite transformation temperature range on the hot band microstructure is described. The magnetic polarization J₅₀₀₀ better than 1.7 T, using hot rolling conditions 40 mm transfer bar thickness, finish mill entry temperature 1000 °C, and finishing temperature 800–840 °C and after decarburization heat treatment and grain growth treatment, was obtained.     

Cathodic electrochemiluminescence at double barrier Al/Al2O3/Al/Al2O3 tunnel emission electrodes

Double insulating barrier tunnel emission electrodes were fabricated by adding a new pure aluminum layer upon oxidized aluminum electrodes by vacuum evaporation and thermally oxidizing the new aluminum layer in air at room temperature. Resulting Al/Al₂O₃/Al/Al₂O₃ electrodes allow the use of various aluminum alloys in the electrode body necessary for hardness or shaping ability of the electrode while obtaining the luminescence properties of pure aluminum oxide. During electrical excitation of luminescent labels by cathodic hot electron injection into aqueous electrolyte solution, the background noise is mainly based on high-field-induced solid-state electroluminescence and F-center luminescence of the outer aluminum oxide film. The more defect states and/or impurity centers the outer oxide film contains, the higher is the background emission intensity. The present electrode fabrication method provides a considerable improvement in signal-to-noise ratio for time-resolved electrochemiluminescence (TR-ECL) measurements when the original native oxide film of the electrode body contains luminescence centers displaying long-lived luminescence. The excellent performance of the present electrodes is demonstrated by extremely low-level detection of Tb(III) chelates, luminol, Pt(II) coproporphyrin and Tb(III) labels in an immunometric immunoassay by time-resolved electrochemiluminescence.     

Heterogeneous and homogeneous electrochemiluminoimmunoassays of hTSH at disposable oxide-covered aluminum electrodes

Heterogeneous and homogeneous immunoassays of human thyroid stimulating hormone (hTSH) were developed on immunometric basis using aromatic Tb(III) chelates as electrochemiluminescent labels and varied types of disposable oxide-covered aluminum electrodes as the solid phase of the immunoassays. The long luminescence lifetime of the present labels allows the use of time-resolved electrochemiluminescence detection and provide the low detection limits of these labels and, thus, sensitive immunoassays. The primary antibody of immunometric immunoassays was coated upon aluminum oxide surface by physical absorption. In homogeneous immunoassays using 66 μl cell and 15 min incubation time, a linear calibration range of 0.25-324 μU/ml was obtained by applying only a single cathodic excitation pulse in the detection step of the assay.     

Anodic behavior of nickel-based alloys in the electrolytic production of NF3

The Ni-based alloys, such as Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si, prepared by hot isostatic pressing (HIP) at 1000 °C under 2 × 10⁸ Pa for 2 h were employed as the anodes for electrolytic production of NF₃. The current efficiencies for NF₃ formation were 42-38, 52-40, 52-47, 63-62, 50 and 41% for Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloys, respectively. The current efficiencies only on Ni-Cu alloys with Cu concentrations lower than 10 mol% were almost the same as those on Ni sheet and HIPed Ni anodes, whereas those on the other alloys used in this study were smaller compared with those on both Ni anodes. On the other hand, the current losses caused by anodic dissolution of Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloy electrodes were 7.95-4.42, 6.40-7.02, 5.60-6.30, 3.34-6.33, 5.10 and 0.18%, respectively. The anode consumptions of Ni-5 mol% Cu and Ni-5 mol% Si alloys were almost the same or smaller compared with those of Ni sheet and HIPed Ni electrodes, though those of other alloys used were large compared with those of both Ni anodes. Consequently, addition of Cu to the nickel matrix is available for a cheaper cost of anode with keeping a same current efficiency as that on the Ni anode and addition of Si to the nickel matrix is effective for decreasing anode consumption largely. A Ni sheet electrode containing a trace of impurities, such as Co, Mn, Ag and Al, is also favorable as the anode for electrolytic production of NF₃.     

Temperature dependence of volume and surface symmetry energy coefficients of nuclei

The thermal evolution of the energies and free energies of a set of spherical and near-spherical nuclei spanning the whole periodic table are calculated in the subtracted finite-temperature Thomas–Fermi framework with the zero-range Skyrme-type KDE0 and the finite-range modified Seyler–Blanchard interaction. The calculated energies are subjected to a global fit in the spirit of the liquid-drop model. The extracted parameters in this model reflect the temperature dependence of the volume symmetry and surface symmetry coefficients of finite nuclei, in addition to that of the volume and surface energy coefficients. The temperature dependence of the surface symmetry energy is found to be very substantial whereas that of the volume symmetry energy turns out to be comparatively mild.     

聚变实验堆真空室壳体成型残余应力分析

为了了解聚变实验堆真空室壳体表面残余应力的分布以及退火工艺对残余应力的影响，通过模拟分析和实验检测两种方式对不锈钢316LN冷压曲面和热压曲面残余应力进行研究，获得退火前后曲面表面残余应力的大小，得到冷压曲面和热压曲面残余应力的分布以及退火工艺对残余应力分布的影响。研究结果为分析成型工艺提供数据支撑，对中国聚变工程实验堆真空室的研究与制造具有重要意义。     

Rapid production of Iron Disilicide thermoelectric material by Hot Press Sintering Route

In present research work, a method has been established through powder metallurgical route to produce β-FeSi₂ thermoelectric material without giving long time mechanical alloying treatment to the elemental powders and long duration heat treatment cycle. The elemental powders of iron (98.9% purity, 200 mesh) and silicon (98.5% purity, 400 mesh) have been mechanically alloyed for 6 h using high-energy Attritor ball-mill and was subjected to Hot Press Sintering (HPS). Effect of HPS parameters on density of compacts was studied. The compacts with higher densities (82–92% relative density) were later on subjected to the thermal cycling treatment. The density as well as the amount of β-FeSi₂ phase formation got enhanced due to thermal cycling treatment.     

风冷压缩单元式空调器节能探讨

从分析风冷压缩单元式空调器的制冷原理入手,提出了两种空气源热泵热水模块＋空气源压缩制冷模块机,为提高能源综合利用效率、节约建筑能耗提供了一定的实践思路。     

UV nanoimprint using flexible polymer template and substrate

Nano to micro-sized patterns were formed on a flexible polymer substrate using a flexible UV imprint stamp. A 6 in. diameter flexible UV nanoimprint template was fabricated using PVC hot embossing and DLC coating. Using the UV nanoimprint process with the DLC coated PVC template, nano to micro-sized patterns were clearly formed on the flexible PET substrate without a residual layer, due to the antistiction properties and high mechanical hardness of the DLC coating. By depositing a Cr layer on the imprinted resist pattern and lifting it off, Cr metal patterns were fabricated on the PET substrate.