单小区模型的掉话率分析

掉话率是无线通信网络中最重要的关键性能指标(KPI)之一,本文分析了中国移动在讨论网络性能评估方法时提出的3个不同的掉话率计算公式,通过建立一个单小区的模型,使用一些合理的假设和分析,从理论上确定了一个最为准确的计算公式.     

Comment on “The Free Will Theorem”

In a recent paper Conway and Kochen, Found. Phys. 36, 2006, claim to have established that theories of the Ghirardi-Rimini-Weber (RW) type, i.e., of spontaneous wave function collapse, cannot be made relativistic. On the other hand, relativistic GRW-type theories have already been presented, in my recent paper, J. Stat. Phys. 125, 2006, and by Dowker and Henson, J. Stat. Phys. 115, 2004. Here, I elucidate why these are not excluded by the arguments of Conway and Kochen.      

Effect of core-shell micelle formation on the redox properties of phenothiazine-labeled poly(ethyl glycidy ether)-block-poly(ethylene oxide)

Redox properties of phenothiazine-labeled poly(ethyl glycidy ether)-block-poly(ethylene oxide) (PT-EGE_n-b-EO_m) are reversibly changed by core-shell micelle formation. In the temperature range higher than the critical micellization temperature (cmt), the anodic potential of PT group positively shifts and concomitantly its anodic current decrease, or levels off compared to those of the reference polymer PT-EO_m without the thermo-responsive EGE_n segment. The former alteration is caused by incorporation of hydrophobic PT groups into a core of the micelle and the latter by the decrease in the diffusion coefficient of PT groups due to formation of the core-shell micelles. The cmt value and the temperature-dependent alteration in the redox properties strongly depend on the polymer structure, especially the length of thermo-responsive EGE_n segment. The electrochemically determined hydrodynamic radii of the polymer aggregates seem to be overestimated, compared to the values reported for the aggregates of other thermo-responsive polymers with similar molecular weights, implying the presence of electrochemically inactive PT groups in the copolymers having longer thermo-responsive segments.     

A novel specimen for investigating the mechanical behavior of elastomers under multiaxial loading conditions

In this paper we describe the design and manufacture of an axial-torsion test specimen, and provide relationships needed when conducting stress-strain characterization experiments with the specimen. The specimen is a short hollow cylinder of rubber bonded between two steel mounting rings, in which simultaneous axial and shear strains are produced via independently controlled axial and twist displacements. We present calculations for the strain-displacement and stress-load relationships, and strain energy density. These relationships have been established and validated via a combination of analytical and experimental techniques, and finite element analysis. We have investigated the extent and effects of strain and stress field non-uniformity in the test specimen. The specimen design is sufficiently simple that a closed-form expression for the strain-displacement relationship has been successfully developed.     

单稳态触发器的结构及其开关级设计原理

根据单稳态触发器定时单元特性,提出了单稳态触发器的一般结构.在此基础上,运用传输电压开关理论进行了CMOS单稳态触发器的开关级设计研究,并具体设计了两个单稳态触发器.设计实例表明文中提出的方法不仅简单、有效,而且具有通用性.     

“Slow” active control of combustion instabilities by modification of liquid fuel spray properties

This paper describes an experimental investigation of the feasibility of using “slow” active control approaches, which “instantaneously” change liquid fuel spray properties, to suppress combustion instabilities. The objective of this control approach was to break up the feedback between the combustion process heat release and combustor pressure oscillations that drive the instability by changing the characteristics of the combustion process (e.g., the characteristic combustion time). To demonstrate the feasibility of such control, this study used a proprietary fuel injector (Nanomiser^TM), which can vary its fuel spray properties, to investigate the dependence of acoustics–combustion process coupling, i.e., the driving of combustion instabilities, upon the fuel spray properties. This study showed that by changing the spray characteristics it is possible to significantly damp combustion instabilities. Furthermore, using combustion zone chemiluminescence distributions, which were obtained by Abel’s deconvolution synchronized with measured acoustic data, it has been shown that the instabilities were mostly driven midway between the combustor centerline and wall, a short distance downstream from the flame holder, where the mean axial flow velocity is approximately zero in the vortex near the flame holder. The results of this study strongly suggest that a “slow” active control system that employs controllable fuel injectors could be effectively used to prevent the onset of detrimental combustion instabilities.     

有限核真空中的反核子能谱

通过建立能够自洽地描述核子和反核子束缚态的相对论Hartree模型来研究有限核中的量子真空,其中狄拉克海对介子场方程的贡献由单圈图考虑,模型中还引入了ω介子和ρ介子的张量耦合项.在拟合球形核的性质后得到模型的参数,给出核子有效质量为m*/MN≈0.78;计算得到的核子壳模型能级与实验值相一致,在考虑张量耦合项的效应后真空反核子位阱深度增大了20—30MeV.     

近场光学显微技术

本文在介绍近场光学显微镜原理的基础上，对近场光学显微技术进行了一定深度的探讨，并着重研究了纳米级探针的制作和纳米级样品与探针间距的控制这两个近场光学显微技术中的关键问题，说明了近场光学显微探针的工作方式，阐述了近场光学成像的衬度类型，介绍了近场光学显微技术在多个领域的应用。在参考大量国内外最新研究成果的基础上，提出了一些个人的见解。     

Unified approach to photo-and electro-production of mesons with arbitrary spins

A new approach to identify the independent amplitudes along with their partial wave multipole expansions, for photo-and electro-production is suggested, which is generally applicable to mesons with arbitrary spin-parity. These amplitudes facilitate direct identification of different resonance contributions.      

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007