Microwave and RF surface wave sustained discharges as plasma sources for plasma chemistry and plasma processing

The surface wave produced plasma belongs to a class of RF and microwave induced plasmas. It results from the propagation of an electromagnetic wave which uses the plasma column it sustains and the plasma tube as its sole propagating media. This type of plasma offers several advantages compared to the positive column plasma of dc discharges or to other RF and microwave produced plasmas. Surface wave plasmas require no internal electrodes, and they can be applied over an extremely broad range of wave frequencies (27 MHz to 10 GHz demonstrated) and gas pressures (about 10^–4 Torr to a few times the atmospheric pressures). Using the surface wave plasma technique, a large variety of plasma column diameters have been created (0.5–150 mm demonstrated) and no limitation on plasma column length (column up to 6 m long demonstrated) has been found. The surface wave produced plasma is used in elemental analysis and to sustain emission in lasing media. This article is intended as a guide for potential users of surface wave plasmas in the field of plasma processing and plasma chemistry.     

Tetrachlorosilane Consumption in Radio Frequency Glow Discharge

Time-resolved mass spectrometry was used for analysis of the plasma reactions in radio frequency (RF) SiCl ₄ and SiCl ₄ –O ₂ discharges as functions of starting partial pressure and electrical power. Molecular concentrations of the reactants and products from SiCl ₄ alone and with O ₂ were obtained from the mass spectra and used for plotting the kinetic curves. The SiCl ₄ and O ₂ consumption rates were calculated from the kinetic curves and compared with results of theoretical simulation of the reaction. Direct electron impact decomposition was found to be the main pathway for pure SiCl ₄ conversion. On the contrary, the consumption of SiCl ₄ in the SiCl ₄ +O ₂ mixtures was largely chemical. The experimental macrokinetics are in agreement with a model in which oxidation is caused by the atomic oxygen.     

带有前置EDFA卫星相干激光通信终端的信噪比分析

卫星激光通信链路是一项实现卫星大规模星座组网的关键技术。相干激光链路灵敏度高、抗背景干扰、速率升级空间大,在星间激光链路中应用广泛。文章建立了带有前置掺铒光纤放大器(EDFA)的卫星相干激光通信终端的信噪比分析模型,仿真分析了EDFA功率增益、EDFA噪声系数、本振光功率、信号光功率、光放后端光带宽、基带前端电带宽对终端输出信噪比的影响以及各种输出噪声功率占比的情况,得到了带有前置EDFA卫星相干激光通信终端的信噪比参数特性。     

一种高增益的宽带低噪声放大器的设计

采用SANAN公司的0.25μm E-Mode pHEMT工艺,基于ADS仿真,设计了一款工作频率为2.0～4.2 GHz的两级级联的宽带LNA芯片。芯片采用电阻偏压的方式,实现了3.3 V单电源供电。同时,设计了一种改进型的RLC并联负反馈结构,实现了宽带匹配。仿真结果表明,该LNA在2.0～4.2 GHz频段内,最大增益为30.9 dB,增益平坦度为±0.6 dB左右,输入回波损耗小于-9 dB,输出回波损耗小于-12 dB;噪声系数为(1.2±0.14) dB;系统稳定性因子K在全频带内大于2.8;芯片面积为0.78 mm×2.2 mm。     

采用辅助转动装置的MIMO 系统双目标DPD 实验研究

文中介绍了一种双目标数字预失真(DPD)方案,并进行了实验研究。不增加系统复杂度的情况下, 可以有效地扩展MIMO 系统的线性化波束宽度。在发射机附近增设一个发射低功率信号的线性辅助转动装置,该 架构实现了MIMO 系统主波束线性化。实验平台由发射机系统和一个辅助转动装置组成,发射机天线阵列为1×4。 输入信号采用两个20 MHz 带宽峰均比分别为5. 7 dB 和5. 6 dB 的正交频分复用(OFDM)信号。实验研究结果表明, 采用了辅助转动装置的双目标DPD 方法后,邻信道功率比(ACPR)达到-50 dBc 以下的主波束线性化宽度可以扩展 到22°,同时信号归一化均方误差(NMSE)平均数值为-40 dB。该方案有效地拓宽了MIMO 系统线性化波束宽度。     

On the design considerations of solid-state power amplifiers for satellite communications: A systems perspective

Conventional solid-state power amplifier (SSPA) design approach isolates radio frequency (RF) design from communication theory. In this paper, a unified SSPA design approach is proposed, which optimizes SSPA parameters (bias voltage and input RF signal power) to minimize total DC power consumption while satisfying received SNR constraint specified by the link budget. The effect of SSPA nonlinearity is quantified by the error vector magnitude measured at its output and the corresponding received SNR degradation is analyzed. Using the quantitative metrics for received SNR, it is possible to evaluate highly nonlinear SSPA classes such as Class-B or deep-Class AB, which are normally not considered in conventional SSPA design approach to be used in satellite communication applications.     

基于40 nm CMOS工艺的高效率功率放大器设计

针对硅基毫米波功率放大器存在的饱和输出功率较低、增益不足和效率不高的问题,基于TSMC 40nm CMOS工艺,设计了一款工作在28GHz的高效率和高增益连续F类功率放大器。提出的功率放大器由驱动级和功率级组成。针对功率级设计了一款基于变压器的谐波控制网络来实现功率合成和谐波控制,有效地提高了功率放大器的饱和输出功率和功率附加效率。采用PMOS管电容抵消功率级的栅源电容,进一步提高线性度和增益。电路后仿真结果表明,设计的功率放大器在饱和输出功率为20.5dBm处的峰值功率附加效率54%,1dB压缩点为19dBm,功率增益为27dB,在24GHz~32GHz频率处的功率附加效率大于40%。     

面向电子战射频光传输的宽带射频信号杂散产生机理及优化方法

针对电子战系统的宽带射频信号波分复用传输,通过理论分析给出了微波光子链路中各关键参量对杂散信号的影响规律,提出了非均匀信道间隔分配的除杂优化方法。该方法通过微调各通道的波长,使四波混频产生的杂散频率超过电子战接收机带宽,从而降低杂散对系统的影响。该方案实现简单,且无需改变现有电子战系统架构,具有较好的工程实现性。实验结果表明:与等波长间隔相比,5通道非均匀波分复用信号传输1 km时,在接收机带宽内四波混频引起的杂散得到了显著优化,动态范围提升了26 dB以上。     

5G 功放DPD 的FPGA 宽带实现及自动优化

5G 宽带功放数字预失真器(DPD)的FPGA 实现过程中,常遇到数字处理带宽不够和资源有限问题,对 此,文中提出一种基于双路并行数据流的数字预失真带宽扩展方法和基于Zynq Ultrascale+ MPSoC 的自动化模型优化 验证方法,可快速实现对5G 宽带功放线性化方案的优化。使用该并行处理结构的数字预失真器,克服了数字电路最 大时钟频率造成的对FPGA 线性化带宽的限制,使得数字预失真电路在每个时钟周期内可以处理更多的数据,不仅有 效地增加了数字处理带宽,而且降低了DPD 的功耗。然而,这种带宽增加以消耗更多硬件资源为代价,对此,文中同时 提出了对预失真非线性模型的在线自动优化方法,以简化非线性模型、降低DPD 的硬件资源开销。最后,在Zynq Ultrascale+ FPGA 实验平台上实现了具有两路并行数据处理的I-MSA 自优化数字预失真电路,采用100 MHz 的5G 新无 线电(NR)信号在2. 6 GHz 功率放大器上进行线性化实验验证,获得了满意的预失真性能,验证了所提方法的有效性。     

多功能射频综合系统中的电磁协同北大核心CSCD

限定时空条件下,射频综合系统有效发挥多功能效应的实质是实现系统多功能协同高效运行,而制约其协同高效运行的瓶颈是特定时空条件下可用的电磁资源。电磁资源的高效利用依赖电磁协同,是按照任务要求及限定条件,在时间、频率、空间、能量多个维度寻求构建电磁协同自组织结构的最优解,并确定具体任务时空下有序运行自组织结构的驱动方式,按照求解出的电磁资源动态分配结果,执行任务,使系统电磁效应在任务牵引下受控。电磁协同服务于多功能射频综合系统融合,可以有效利用、管理战场电磁环境,高效提升多功能射频综合系统的运行效率。本文从多功能射频综合系统融合运行之瓶颈、电磁协同概念和电磁协同方法三个方面论述电磁协同的核心要点,期望为实现多功能射频综合系统融合运行提供可行的技术途径。