一种基于厚膜技术的浮动板调制器的设计

本文设计了一种基于厚膜技术的浮动板调制器,通过试验证明,该调制器具有结构简单、可靠性高、输出波形好,通用性强等优点。     

新型低压无功补偿器的设计

主要介绍了基于ATT7022B和ST-SRC或ST-SRCS-4智能开关的新型无功补偿统。该控制器通过高精度多功能三相电能专用计量芯片ATT7022B实时检测电网的电压、电流、功率因数、无功电流和无功功率,并有CAN总线通信接口。ST-SRC或ST-SRCS-4智能开关可在电压或电流过零点时动作,并可以通过CAN总线接口与和无功补偿控制器进行通信,最终使电容器组按一定的规律进行投切,最终实现无功补偿。     

Redox‐induced configuration conversion for thioacetamide dimer can function as a molecular switch

The electronic switching properties of thioacetamide dimer (TAD) were investigated using the nonequilibrium Green's function method combined with density functional theory for design of a novel molecular switch. The H‐bonded TAD can be converted upon hole‐trapping to a three‐electron (3e)‐bonded configuration with a S∴S linkage which could provide a more favorable channel for charge transfer than the before. The redox‐induced configuration conversion between the H‐bonded and the 3e‐bonded TADs could govern the charge migration through the molecular junction with a considerable difference in conduction currents. The calculated I–V characteristic curves of two configurations exhibit a switching behavior with an On‐Off ratio in a range of about 4.3–7.6 within the applied voltages. Clearly, this hypothetical scheme provides a potential way to explore the novel conformation‐dependent molecular switch. © 2010 Wiley Periodicals, Inc. J Comput Chem 2010     

Development of a switchable multidimensional/comprehensive two-dimensional gas chromatographic analytical system

In this study, a new system for analysis using a dual comprehensive two-dimensional gas chromatography/targeted multidimensional gas chromatography (switchable GC × GC/targeted MDGC) analysis was developed. The configuration of this system not only permits the independent operation of GC, GC × GC and targeted MDGC analyses in separate analyses, but also allows the mode to be switched from GC × GC to targeted MDGC any number of times through a single analysis. By incorporating a Deans switch microfluidics transfer module prior to a cryotrapping device, the flow stream from the first dimension column can be directed to either one of two second dimension columns in a classical heart-cutting operation. Both second columns pass through the cryotrap to allow solute bands to be focused and then rapidly remobilized to the respective second columns. A short second column enables GC × GC operation, whilst a longer column is used for targeted MDGC. Validation of the system was performed using a standard mixture of compounds relevant to essential oil analysis, and then using compounds present at different abundances in lavender essential oil. Reproducibility of retention times and peak area responses demonstrated that there was negligible variation in the system over the course of multiple heart-cuts, and proved the reliable operation of the system. An application of the system to lavender oil, as a more complex sample, was carried out to affirm system feasibility, and demonstrate the ability of the system to target multiple components in the oil. The system was proposed to be useful for study of aroma-impact compounds where GC × GC can be incorporated with MDGC to permit precise identification of aroma-active compounds, where heart-cut multidimensional GC-olfactometry detection (MDGC-O) is a more appropriate technology for odour assessment.     

基于FPGA的多路视频通道控制

根据织布机告警系统的需求,提出一种开关设计思想,阐述开关设计过程中遇到的问题以及解决方法。首先在FPGA中设计一个开关控制信号,利用这个信号结合双口RAM中的编码数据识别两个拨动开关状态．从而达到控制多路视频通道的目的,使本告警系统更方便的应用于实际工业中。介绍整个控制系统的工作原理,给出硬件结构图和软件设计过程,然后利用QnartusⅡ中的SignalTapⅡLogic Analyzer工具对控制信号进行实时采样分析．最后在织布机告警系统中成功实现视频通道控制功能。     

全光网络中的波长选择器件

随着光通信技术的发展,特别是光波分复用（WDM）技术的广泛应用,光交叉连接技术（OXC）和光分插复用技术（OADM）受到了越来越多的关注。波长选择器件因具有对不同波长自由选取的功能而在以上两种技术中起到了十分重要的作用。本文介绍了目前研究的几种典型的波长选择器件,对它们的特点进行了分析和比较。     

L波段六位数字移相器设计

利用对均匀传输线加载电纳可以改变其传输特性的原理设计了一个L波段六位色散数字移相器.借助ADS软件及25.D仿真器Momentum,建立PIN二极管的SPICE模型,使用Au丝测试得的S参数,在全面考虑实际制作工艺的基础之上,建立准确的电路模型,经过优化,可以得到准确的仿真结果.实际测试结果与仿真相吻合.该方法减少了调试工作,且设计的产品性能优良,体积小,已得到公司规模生产.     

用于12 bit 40 MS/s低功耗流水线ADC的采样保持电路

设计了一个可降低12 bit 40 MHz采样率流水线ADC功耗的采样保持电路。通过对运放的分时复用,使得一个电路模块既实现了采样保持功能,又实现了MDAC功能,达到了降低整个ADC功耗的目的。通过对传统栅压自举开关改进,减少了电路的非线性失真。通过优化辅助运放的带宽,使得高增益运放能够快速稳定。本设计在TSMC0.35μm mix signal 3.3 V工艺下实现,在40 MHz采样频率,输入信号为奈奎斯特频率时,其动态范围(SFDR)为85 dB,信噪比(SNDR)为72 dB,有效位数(ENOB)为11.6 bit,整个电路消耗的动态功耗为14 mW。     

频分制红外遥控开关电路的设计

介绍频分制红外遥控开关电路的设计与实现。遥控开关电路的类型很多,采用频分制具有电路简单、易于实现,可广泛应用于家庭、办公场所的开关控制。频分制有多种实现方法,该设计主要采用NE555定时器作为发射电路的核心器件,接收电路采用通用音频译码器I。M567作为主要器件,制作方便,易于推广使用。经安装调试,控制效果较好。     

PLC控制系统在火力发电厂的应用及注意事项

主要论述了PLC控制系统的发展方向、应用领域,以及PLC系统自身的一些特点,并重点论述了其在安装、使用过程中的注意事项和对系统、设备、环境的要求、标准。分析了PLC在实际使用过程中出现的一些常见问题,为PLC系统今后的应用和普及总结出经验和方法。