过渡金属络合物的非线性光学性质的研究

报道了具有良好电荷转移特性的Ｒｕ络合物，采用四波混频方法对其非线性光学性能进行了测量，由此推算出三阶非线性光学极化率和分子的超极化率，并讨论了不同配体对三阶非线性光学系数的影响     

非水体系中哌啶在银电极表面的表面增强喇曼散射

本文测定了哌啶在甲醇溶液中吸附在银电极表面的表面增强喇曼散射(SERS)光谱,及其随电位的变化,同时还测定了电极经不同氧化-还原循环(ORC)预处理时的SERS谱,对所得结果进行了分析比较,并进一步研究了非水体系和水体系SERS谱之间的关系.实验结果表明:哌啶在甲醇体系中比在水体系中SERS谱的增强因子要小,并且它们的SERS谱线随电位的变化也有一定的差别.     

Low‐Temperature Growth of SiO2 Films by Plasma‐Enhanced Atomic Layer Deposition

Silicon dioxide (SiO₂) films prepared by plasma‐enhanced atomic‐layer deposition were successfully grown at temperatures of 100 to 250 °C, showing self‐limiting characteristics. The growth rate decreases with an increasing deposition temperature. The relative dielectric constants of SiO₂ films are ranged from 4.5 to 7.7 with the decrease of growth temperature. A SiO₂ film grown at 250 °C exhibits a much lower leakage current than that grown at 100°C due to its high film density and the fact that it contains deeper electron traps.     

Piezoelectricity of ordered (ScxGa1-xN) alloys from first principles

First-principles calculations are performed to compute the e₃₃ piezoelectric coefficients of GaN, ScN and (Sc_xGa_1-xN) alloys exhibiting an alternation of hexagonal GaN, with hexagonal ScN along the c-axis. For Sc compositions larger than 50%, each atom has nearly five nearest neighbors (i.e., the ground state exhibits a phase that is five-fold coordinated). On the other hand, Sc-deficient (Sc, Ga) N alloys adopt a ground-state that is four-fold coordinated). The magnitude of e₃₃ in the Sc-deficient ideally ordered (Sc_0.25Ga_0.75N) is found to be larger than the magnitude of the corresponding e₃₃ coefficients resulting from the compositional weighted average over the hexagonal (h-ScN) and the wurtzite (w-GaN) parent compounds. On the other hand, the e₃₃ coefficients of the Sc-rich ordered (Sc_0.75Ga_0.25N) is found to be negligibly small. In addition, e₃₃ piezoelectric coefficients in ordered (Sc_0.5Ga_0.5N) exhibit quite large magnitudes, due to the nonpolar to polar transition occurs at Sc composition x = 0.5, and thus can bridge the corresponding coefficients of (Ga, In) N and ferroelectric alloys. The microscopic origins for this huge enhancement in the piezoelectric behavior in Sc-low and Sc-intermediate alloys and the role of each atom are revealed and discussed.     

Enhanced patch test of finite element methods

Theoretically, the constant stress patch test is not rigorous. Also, either the patch test of non-zero constant shear for Mindlin plate problem or non-zero strain gradient curvature of the microstructures cannot be performed. To improve the theory of the patch test, in this paper, based on the variational principle with relaxed continuity requirement of nonconforming element for homogeneous differential equations, the author proposed the individual element condition for passing the patch test and the convergence condition of the element: besides passing the patch test, the element function should include the rigid body modes and constant strain modes and satisfy the weak continuity condition, and no extra zero energy modes occur. Moreover, the author further established a variational principle with relaxed continuity requirement of nonconforming element for inhomogeneous differential equations, the enhanced patch test condition and the individual element condition. To assure the convergence of the element that should pass the enhanced patch test, the element function should include the rigid body modes and non-zero strain modes which satisfied the equilibrium equations, and no spurious zero energy modes occur and should satisfy new weak continuity condition. The theory of the enhanced patch test proposed in this paper can be applied to both homogeneous and inhomogeneous differential equations. Based on this theory, the patch test of the non-zero constant shear stress for Mindlin plate and the C^0–1 patch test of the non-zero constant curvature for the couple stress/strain gradient theory were established.     

Intelligent Fault Identification for Rolling Bearings Fusing Average Refined Composite Multiscale Dispersion Entropy-Assisted Feature Extraction and SVM with Multi-Strategy Enhanced Swarm Optimization

Rolling bearings act as key parts in many items of mechanical equipment and any abnormality will affect the normal operation of the entire apparatus. To diagnose the faults of rolling bearings effectively, a novel fault identification method is proposed by merging variational mode decomposition (VMD), average refined composite multiscale dispersion entropy (ARCMDE) and support vector machine (SVM) optimized by multistrategy enhanced swarm optimization in this paper. Firstly, the vibration signals are decomposed into different series of intrinsic mode functions (IMFs) based on VMD with the center frequency observation method. Subsequently, the proposed ARCMDE, fusing the superiorities of DE and average refined composite multiscale procedure, is employed to enhance the ability of the multiscale fault-feature extraction from the IMFs. Afterwards, grey wolf optimization (GWO), enhanced by multistrategy including levy flight, cosine factor and polynomial mutation strategies (LCPGWO), is proposed to optimize the penalty factor C and kernel parameter g of SVM. Then, the optimized SVM model is trained to identify the fault type of samples based on features extracted by ARCMDE. Finally, the application experiment and contrastive analysis verify the effectiveness of the proposed VMD-ARCMDE-LCPGWO-SVM method.     

A low-threshold multiwavelength Brillouin fiber laser with double-frequency spacing based on a small-core fiber

We demonstrate multiwavelength Brillouin fiber lasers (MWBFLs) with double-frequency spacing based on a small-core fiber (SCF) and a standard single-mode fiber (SMF), which have core diameters of 5 and 8.8 μm, respectively. Experimental results show that the SCF-based MWBFL exhibits a higher laser output power and a lower pump threshold. The output powers of the SCF-based MWBFL are > 1.4 times those of the SMF-based MWBFL. Moreover, the threshold power required to generate each channel of the SCF-based MWBFL is 59% that of the SMF-based MWBFL. When the same pump power of 180 mW is injected, the number of laser channels generated for the SCF-based MWBFL is 13, which is twice that generated for the SMF-based MWBFL. In addition, the SCF-based MWBFL exhibits good wavelength tunability from 1535 to 1565 nm and temporal stability over an hour.     

PDMS-Au复合基底上多环芳烃分子的表面增强拉曼光谱

利用聚二甲基硅氧烷(PDMS)对有机物的富集功能,通过在金纳米粒子单层膜(Au MLF)表面旋涂薄层PDMS膜制备PDMS-Au MLF复合表面增强拉曼光谱(SERS)基底.研究了SERS增强性能与旋涂液浓度及稀释溶剂间的关系,考察了复合基底增强活性的均匀性.研究发现,采用叔丁醇为稀释溶剂,浓度为2%(质量分数)的旋涂液时所得复合基底表面多环芳烃(PAHs)的SERS信号强度最高,且此基底SERS信号强度偏差小于10%.分别以PDMS-Au MLF复合材料和Au MLF作为基底,对比研究了对萘、蒽、菲和芘4种多环芳烃的SERS检测能力.结果表明,PDMS-Au MLF复合基底对以上4种有机物的检出限分别为10~(-6),10~(-7),10~(-8)及10~(-7)mol/L,相比于单一Au MLF基底,其检测限至少降低了1个数量级,这主要源自于PDMS对PAHs的富集作用,且此类复合基底可用于多种多环芳烃混合物的特征识别.     

基于光子晶体带边效应的表面增强拉曼基底

将光子晶体的带边效应与金纳米粒子的拉曼散射增强作用相结合,制备了一种新型光子晶体表面增强拉曼散射基底(PC-AuNPs),利用罗丹明B(RhB)作为报告分子,对所得基底性能进行检测.PC-AuNPs基底的制备包括3个步骤:在SiO2微球表面修饰氨基,再通过垂直沉降自组装得到蛋白石结构光子晶体(PC), 最后, 在光子晶体表面负载金纳米粒子(AuNPs).结果表明,光子晶体的带隙范围及AuNPs的负载量直接影响了PC-AuNPs基底的检测效果;以所得的PC-AuNPs基底测定RhB分子,其拉曼散射特征峰强度与浓度对数值呈现良好的线性关系,线性方程为I=1711lg[RhB(mol/L)]+15244,线性相关系数R2=0.9994,检出限为1×10-8 mol/L,表明此PC-AuNPs基底可用于目标物的定性及定量检测.本方法提高了传统拉曼散射光谱检测灵敏度,操作简单,具有良好的重现性,可为其它新型检测基底的制备提供.     

A new third‐order calibration method with application for analysis of four‐way data arrays

A novel third‐order calibration algorithm, alternating weighted residue constraint quadrilinear decomposition (AWRCQLD) based on pseudo‐fully stretched matrix forms of quadrilinear model, was developed for the quantitative analysis of four‐way data arrays. The AWRCQLD algorithm is based on the new scheme that introduces four unique constraint parts to improve the quality of four‐way PARAFAC algorithm. The tested results demonstrated that the AWRCQLD algorithm has the advantage of faster convergence rate and being insensitive to the excess component number adopted in the model compared with four‐way PARAFAC. Moreover, simulated data and real experimental data were analyzed to explore the third‐order advantage over the second‐order counterpart. The results showed that third‐order calibration methods possess third‐order advantages which allow more inherent information to be obtained from four‐way data, so it can improve the resolving and quantitative capability in contrast with second‐order calibration especially in high collinear systems. Copyright © 2011 John Wiley & Sons, Ltd.