Modeling of radiative heat transfer in an axisymmetric cylindrical enclosure with participating medium

Radiative heat transfer in an axisymmetric enclosure with absorbing, emitting, and scattering medium is studied here by using the different methods such as MDOM, FVM, and MFVM with emphasis on the treatment of angular derivative term, which appears in curvilinear coordinates due to angular redistribution. After final discretization equation for MFVM is introduced by using the step scheme and directional weights, the present approach is validated by applying it to three different benchmarking problems with absorbing, emitting, and scattering medium. All of the results presented here support its accuracy as well as moderate efficiency. Finally, the present approaches are applied to a truncated cone-shaped enclosure as a body-fitted geometry case.     

Influence of organic modifiers on morphology and crystallization of poly(ϵ‐caprolactone)/synthetic clay intercalated nanocomposites

ε‐caprolactone was polymerized in the presence of neat montmorillonite or organomontmorillonites to obtain a variety of poly(ε‐caprolactone) (PCL)‐based systems loaded with 10 wt % of the silicates. The materials were thoroughly investigated by different X‐ray scattering techniques to determine factors affecting structure of the systems. For one of the nanocomposites it was found that varying the temperature in the range corresponding to crystallization of PCL causes reversible changes in the interlayer distance of the organoclay. Extensive experimental and literature studies on this phenomenon provided clues indicating that this effect might be a result of two‐dimensional ordering of PCL chains inside the galleries of the silicate. Small angle X‐ray scattering and wide angle X‐ray scattering investigation of filaments oriented above melting point of PCL revealed that polymer lamellae were oriented perpendicularly to particles of unmodified silicate, while in PCL/organoclay systems they were found parallel to clay tactoids. Calorimetric and microscopic studies shown that clay particles are effective nucleating agents. In the nanocomposites, PCL crystallized 20‐fold faster than in the neat polymer. The crystallization rate in nanocomposites was also significantly higher than in microcomposite. Further research provided an insight how the presence of the filler affects crystalline fraction and spherulitic structure of the polymer matrix in the investigated systems. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2350–2367, 2007     

Diblock copolymers based on allyl methacrylate: Synthesis,characterization, and chemical modification

Different diblock copolymers constituted by one segment of a monomer supporting a reactive functional group, like allyl methacrylate (AMA), were synthesized by atom transfer radical polymerization (ATRP). Bromo‐terminated polymers, like polystyrene (PS), poly(methyl methacrylate) (PMMA), and poly(butyl acrylate) (PBA) were employed as macroinitiators to form the other blocks. Copolymerizations were carried out using copper chloride with N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as the catalyst system in benzonitrile solution at 70 °C. At the early stage, the ATRP copolymerizations yielded well‐defined linear block copolymers. However, with the polymerization progress a change in the macromolecular architecture takes place due to the secondary reactions caused by the allylic groups, passing to a branched and/or star‐shaped structure until finally yielding gel at monomer conversion around 40% or higher. The block copolymers were characterized by means of size exclusion chromatography (SEC), ¹H NMR spectroscopy, and differential scanning calorimetry (DSC). In addition, one of these copolymers, specifically P(BA‐b‐AMA), was satisfactorily modified through osmylation reaction to obtain the subsequent amphiphilic diblock copolymer of P(BA‐b‐DHPMA), where DHPMA is 2,3‐dihydroxypropyl methacrylate; demonstrating the feasibility of side‐chain modification of the functional obtained copolymers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3538–3549, 2007     

Novel UV‐induced photografting process for preparing poly(tetrafluoroethylene)‐based proton‐conducting membranes

A novel process comprising the UV‐induced photografting of styrene into poly(tetrafluoroethylene) (PTFE) films and subsequent sulfonation has been developed for preparing proton‐conducting membranes. Although under UV irradiation the initial radicals were mainly generated on the surface of the PTFE films by the action of photosensitizers such as xanthone and benzoyl peroxide, the graft chains were readily propagated into the PTFE films. The sulfonation of the grafted films was performed in a chlorosulfonic acid solution. Fourier transform infrared and scanning electron microscopy were used to characterize the grafted and sulfonated membranes. With a view to use in fuel cells, the proton conductivity, water uptake, and mechanical properties of the prepared membranes were measured. Even through the degree of grafting was lower than 10%, the proton conductivity in the thickness direction of the newly prepared membranes could reach a value similar to that of a Nafion membrane. In comparison with γ‐ray radiation grafting, UV‐induced photografting is very simple and safe and is less damaging to the membranes because significant degradation of the PTFE main chains can be avoided. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2624–2637, 2007     

Application of N,N‐bis(diphenylphosphino)aniline palladium(II) complexes as pre‐catalysts in Heck coupling reactions

Palladium(II) complexes with N,N‐bis(diphenylphosphino)aniline ligands catalyse the Heck reaction between styrene and aryl bromides, affording stilbenes in good yield. The structures of two of the complexes used as pre‐catalysts have been determined by single‐crystal X‐ray diffraction. Copyright © 2007 John Wiley & Sons, Ltd.     

ATM-PON光网络终端管理控制协议

遵照 ITU- TG.983建议 ,建立 ONT管理和控制通道 ,实现 ONT与 OLT间的管理控制信息传送。并校正了多信息流传送时可能会产生的并发消息错误     

Incomplete data problems in X-ray computerized tomography

Summary In the present paper we study truncated projections for the fanbeam geometry in computerized tomography. First we derive consistency conditions for the divergent beam transform. Then we study a singular value decomposition for the case where only the interior rays in the fan are provided, as for example in region-of-interest tomography. We show that the high angular frequency components of the searched-for densities are well determined and we present reconstructions from real data where the missing information is approximated based on the singular value decomposition.The work of the authors was supported by the Deutsche Forschungsgemeinschaft under grant Lo 310/2-4     

RO-heparin Inhibits L-Selectin-mediated Neutrophils Adhesion to Vascular Endothelium Under Flow Conditions

Introduction Migrationandrecruitmentofleukocytesfromblood toinflammatorylesionsitesaresequentiallyregulated byadhesionmoleculesandtheirreceptors[1].These lectinfamilyplaysamajorroleininitiatingattachement ofneutrophilstotheactivatedendothelium.P selectin,…     

Deconvolution of very low primary energy SIMS depth profiles

In this paper, the deconvolution of SIMS profiles analysed at very low primary energy (0.5 keV/O₂⁺) is addressed. The depth resolution function (DRF) of the SIMS analysis in presence of roughness is established and a deconvolution procedure is implemented without or in presence of roughness on samples containing delta-doped layers of boron in silicon. It is shown that the deconvolution procedure can lead to a great improvement of the full width at half maximum (FWHM) of the measured peaks in the case where no roughness in detected in the crater bottom. In the case where it is present, the conditions required to use a deconvolution procedure are discussed, and the deconvolution is implemented using precise and restrictive assumptions.     

中物院远红外自由电子激光实验研究

中国工程物理研究院基于射频直线加速器技术的远红外自由电子激光(FIR-FEL)实验取得阶段性进展,于2005年3月24晚8时30分首次出光, 并多次重复. 中心波长115μm, 谱宽1%.介绍了实验系统的主要组成部分和主要实验结果.