Off‐grid DoA estimation method of wideband signals

In this paper, an off‐grid direction of arrival (DoA) estimation method is proposed for wideband signals. This method is based on the sparse representation (SR) of the array covariance matrix. Similar to the time domain DoA estimation methods, the correlation function of the sources was assumed to be the same and known. A new measurement vector is obtained using the lower‐left triangular elements of the covariance matrix. The DoAs are estimated by quantizing the entire range of continuous angle space into discrete grid points. However, the exact DoAs may be located between two grid points; therefore, this estimation has errors. The accuracy of DoA estimation is improved by the minimization of the difference between the new measurement vector and its estimated values. Simulation results revealed that the proposed method can enhance the DoA estimation accuracy of wideband signals.     

干扰条件下的“北斗”信号解扩重构DOA估计

在干扰条件下，卫星导航抗干扰波束形成算法往往需要卫星信号波达方向（Direction-of-Arrival，DOA）的先验信息。但当存在低信噪比信号或主动干扰源时，常规的DOA估计算法性能急剧下降甚至失效。针对此问题，提出了一种被干扰信号压制的低信噪比“北斗”信号的DOA估计算法。该算法首先通过对接收信号进行子空间投影抑制干扰信号，然后对抑制干扰后的信号进行解扩重构处理，最后通过多重信号分类算法完成对“北斗”信号的DOA估计。仿真结果表明，在干扰信号干信比80 dB条件下，“北斗”信号DOA估计误差在5°以内，为下一步进行波束形成计算提供了高精度的入射角信息。     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

Response surface methodology toward the optimization of high-energy carotenoid extraction from Aristeus antennatus shrimp

High-energy assisted extraction techniques, like ultrasound assisted extraction (UAE) and microwave assisted extraction (MAE), are widely applied over the last years for the recovery of bioactive compounds such as carotenoids, antioxidants and phenols from foods, animals and herbal natural sources. Especially for the case of xanthophylls, the main carotenoid group of crustaceans, they can be extracted in a rapid and quantitative way with the use of UAE and MAE.     

Synthesis of diisocyanides with phenolic groups and their polymerization to helically chiral poly(quinoxaline‐2,3‐diyl)s

The development of synthetic routes which lead to five new diisocyanide monomers with one or two phenolic groups is described. Their polymerization behavior is studied with Pd‐ and Ni‐based initiators, as well as under microwave irradiation. The polymerizability is mainly dominated by steric effects as is concluded from experiments using different protecting groups. Chiroptical properties of these new polymers are studied by CD‐spectroscopy. After deprotection, helically chiral poly(quinoxalin‐2,3‐diyl)s are obtained which display a Brønsted function attached to a stereolabile biaryl axis whose configuration should be influenced by the chiral polymer backbone. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1320–1329     

Intelligent Information‐Centric Networking routing scheme under imprecise information

Information‐Centric Networking (ICN) has been accepted to overcome some weaknesses of the current Internet architecture, showing that “what is being exchanged” is more important than “who are exchanging information.” Given the inadequate considerations on Quality of Service (QoS) and energy saving in ICN routing, we propose in this paper a routing algorithm to enhance the two aspects. At first, on one hand, Cauchy distribution is used as a fuzzy model to evaluate users' QoS requirements, such as bandwidth, delay, and error rate; on the other hand, we formulate energy saving problem to evaluate the green quality of routing algorithm. Then, we design a link selection approach by considering QoS and energy saving, which belongs to a multi‐objective decision problem resolved by intelligent drops algorithm. Finally, we implement the proposed algorithm and compare it with the famous adaptive forwarding mechanism in terms of some significant metrics, and the experimental results reveal that the proposed algorithm is more efficient.     

The deformation and fracture of balloons

Inflation of balloons provides a straightforward way of achieving large biaxial deformations. Previous studies have shown that when a balloon bursts, crack propagation occurs at very high speed – much higher than would be expected from the low strain modulus and elastic wave velocity of the rubber. The present paper is concerned with studies of the deformation and fracture of cylindrical balloons. On inflation, the deformations of such a balloon pass through an unstable region but subsequently increase monotonically with pressure. In this relatively high pressure region, the ratio of the longitudinal and circumferential extension ratios is broadly in accord with expectations from high-strain elasticity theory when the ratio of the corresponding stresses is taken into account. On bursting, crack speeds up to around 300 m/s in this region. It is shown that these speeds are in accord with large increase in incremental moduli for the highly-strained rubber. Marked changes in crack tip profile observed at very high crack speeds are consistent with control of the rate of growth by inertia rather than by the viscoelastic properties of the rubber (as is believed to be the case at lower speeds). Consistent with this, various elastomers having different glass transition temperatures show similar crack growth behaviour in the very high speed region.