Monte Carlo simulation of spatial distribution of X rays in multifilm targets. III: optimum design as applied to W/Al‐film targets

The brightness of the X‐ray source in a W/Al‐film target used for X‐ray projection microscopy was studied by an approach using the Monte Carlo simulation. Since continuous X rays generated in a thin film have a specific angular distribution of emission, the brightness of the continuous X‐ray source cannot simply be estimated on the assumption that the angular distribution is homogeneous. The newly developed approach using the Monte Carlo simulation enables the evaluation of the effective source size, angular distribution, and brightness of a continuous X‐ray source with sufficient accuracy that it leads to the optimum design of a high‐brightness X‐ray source for uses such as X‐ray projection microscopy. The Monte Carlo calculations were performed for W(Δz)/Al (200 µm)‐film targets with different thicknesses of W film, Δz, under bombardment of 60 kV electrons. The results have suggested an optimum design consisting of a W (2 µm)/Al (200 µm)‐film target as most promising for providing an X‐ray source of higher brightness than the W (5 µm)/Al (200 µm)‐film target, which has already been in practice for X‐ray projection microscopy. Copyright © 2006 John Wiley & Sons, Ltd.     

Influence of the variable wall thickness of the sample tubes and a quartz Dewar on the EPR signal intensity in a single TE102 and double TE104 rectangular cavity

The response of a single TE₁₀₂ and double TE₁₀₄ rectangular cavity to the insertion of samples contained in tubes with variable wall thickness and a quartz Dewar into the cavity has been analyzed. A direct, indirect, and concurrent (positive or negative) “lens effect” inside the double TE₁₀₄ rectangular cavity is discussed. The experimental dependence of the EPR signal intensity on the wall thickness of the sample tube, δ, for the line-like samples with identical length of the sample material column, L=30 mm, recorded in the microwave cavity showed a directly proportional increase of the relative “lens effect” with the increase of the wall thickness of the tube in the interval, δ∈<0.1 mm, >0.5 mm. The insertion of the variable-temperature double-wall quartz Dewar (home-built, resonant frequency shift, ca. −300 MHz) into the single TE₁₀₂ rectangular cavity showed the same relative “lens effect”, with ca. 1.5-time increase of the EPR signal intensity, for a point-like sample and the line-like samples with material columns of diameter of 1 and 1.3 mm, and wall thickness of the sample tubes, δ∈<0.1 mm, >0.5 mm. The increased effect of the Dewar arises because the active volume of the quartz Dewar tube walls is always much more larger than the active volume of the sample tube wall. In the case of the double TE₁₀₄ rectangular cavity, the insertion of the quartz Dewar: (i) into the same cavity, in which the sample is present, caused a direct “lens effect”, with ca. 1.8-fold increase of the EPR signal intensity; however, (ii) into the complementary cavity, in which the sample is absent, caused an indirect “lens effect”, with ca. 0.6-fold decrease of the EPR signal intensity. With the Dewar and sample in one cavity and a large empty sample tube in the complementary cavity, a concurrent (positive or negative) “lens effect” can be observed. Thus, the possible increase/decrease of the EPR signal intensity depends on the volume ratio of the quartz Dewar tube walls and large sample tube wall inserted into the double TE₁₀₄ rectangular cavity. Each of the above phenomena may be a significant source error in quantitative EPR spectrometry unless the samples to be compared in the quantitative EPR analysis are contained in sample tubes having the same wall thickness and each EPR spectra should be recorded inside an identical quartz Dewar.     

测量圆盘转动惯量产生误差的曲线研究

结合三线摆实验的基本过程,进行实验数据的采集。利用投影法来测量圆盘的转角大小,借助于matlab的cftool工具箱,对数据进行曲线拟合,对测出来的二组数据拟合,得到转角与百分差曲线图。通过误差的大小比较,得出圆盘转动惯量测量值与理论值的百分差随转角变化最接近于三次曲线。     

一种不同地面分辨率图像的拼接算法

航空遥感监测中变焦镜头的广泛应用以及飞行高度的变化会获得不同地面分辨率的航空影像,因此为了实时监控到飞行区域的整体情况,需要对不同地面分辨率的图像进行拼接。提出了针对不同地面分辨率图像进行拼接的方法。首先用四分法对图像进行分割,检测变化倍率,选择配准策略;然后用基于加速鲁棒性特征(Speeded-Up Robust Features,SURF)的算法对相邻图像进行拼接。获得了焦距变化从高倍过渡到低倍,或从低倍过渡到高倍的拼接图像。通过航空变焦模拟影像的拼接实验和地面变焦影像的拼接实验表明,该方法能够对不同地面分辨率的图像进行拼接,且拼接结果均以高分辨率为基准。     

Ethylenically unsaturated polycarbosiloxanes for novel silicone hydrogels: synthesis,end‐group analysis,contact lens formulations,and structure–property correlations

A series of novel mono‐ethylenically unsaturated polycarbosiloxanes macromonomers as compatibilizer materials for soft silicon hydrogels were prepared from the anionic ring‐opening polymerization (AROP) of 2,2,5,5‐tetramethyl‐2,5‐disila‐1‐oxacyclopentane followed by methacrylation. The characterization was performed by end‐group analysis and included the determination of molecular weight, molecular weight distributions, end‐group functionality, and impurity profiles using gas chromatography‐mass spectrometry, gel permeation chromatography, nuclear magnetic resonance, and matrix‐assisted laser desorption/ionization time of flight mass spectrometry. The synthetic procedure was optimized to minimize the formation of any dimer that would have the potential to act as a low molecular weight cross linker. In addition, the novel di‐ethylenically unsaturated polycarbosiloxanes were synthesized by cationic polymerization. Use of these silicone derivatives was explored in the formulation of contact lenses, and the structure–property relationship was examined. When copoymerized with hydrophilic monomers, these were able to give transparent and wettable films with desired properties, particularly a low moduli for contact lenses. Contact lens with high modulus is often shown to impart a higher degree discomfort when worn upon the eye. It was clear from the structure–property relationship that the modulus and the tensile strength of the formulated material depend on the nature and length of the polycarbosiloxane used and may be tuned for the purpose as needed. Copyright © 2013 John Wiley & Sons, Ltd.     

A multivariate evolutionary credibility model for mortality improvement rates

The present paper proposes an evolutionary credibility model that describes the joint dynamics of mortality through time in several populations. Instead of modeling the mortality rate levels, the time series of population-specific mortality rate changes, or mortality improvement rates are considered and expressed in terms of correlated time factors, up to an error term. Dynamic random effects ensure the necessary smoothing across time, as well as the learning effect. They also serve to stabilize successive mortality projection outputs, avoiding dramatic changes from one year to the next. Statistical inference is based on maximum likelihood, properly recognizing the random, hidden nature of underlying time factors. Empirical illustrations demonstrate the practical interest of the approach proposed in the present paper.     

“多角度欣赏面心立方晶胞”教学设计*

尝试利用“火花学院”App等在线交互资源,引导学生从立体几何及密置层堆积模型视角,观察、描述、绘制面心立方晶胞的正四面体填隙、正八面体填隙、三视图和沿体对角线投影图像,加深学生对以面心立方晶胞结构为基础的CaF₂→金刚石晶胞、NaCl→钙钛矿晶胞结构的理解;再结合新型材料透明镁铝尖晶石晶体结构的探讨,了解晶体制备中的掺杂改性等常用方法,发展学生的微观探析能力和科学创新意识。     

Jordan operator algebras revisited

Jordan operator algebras are norm‐closed spaces of operators on a Hilbert space with for all . In two recent papers by the authors and Neal, a theory for these spaces was developed. It was shown there that much of the theory of associative operator algebras, in particular, surprisingly much of the associative theory from several recent papers of the first author and coauthors, generalizes to Jordan operator algebras. In the present paper we complete this task, giving several results which generalize the associative case in these papers, relating to unitizations, real positivity, hereditary subalgebras, and a couple of other topics. We also solve one of the three open problems stated at the end of our earlier joint paper on Jordan operator algebras.     

基于ELM算法的羊肉水分含量的快速无损检测

在近红外光谱900-1700nm的波长范围内采集南疆羊肉的光谱数据,来研究水分含量的快速无损检测.为减弱非目标因素对光谱的影响,采用SNV和去趋势法对光谱数据进行预处理.为降低建模的复杂度,去除共线性的影响,采用连续投影算法和相关系数法相结合选取8个特征波长变量,最后使用PLS和ELM算法分别进行建模.实验表明,与采用全光谱波段建模相比,采用特征波长变量建模,PLS和ELM算法的运行时间都大大缩短,并且在运行时间和预测精度上,ELM算法均优于PLS算法.ELM算法采用8个特征波段变量建模,预测精度达到0.9768,均方误差为4.4291e-04,相关系数为0.7603,运行时间可控制在1e-04s之下,这可为研发羊肉水分含量的便携式检测装置提供理论参考.