稀土变质热锻模具铸钢高温磨损性能的研究

研究了稀土（RE）变质热锻模具铸钢的高温磨损性能，并与热锻模具钢H13钢和3Cr2W8V钢进行对比，探讨了稀土元素的作用和热锻模具铸钢的高温磨损机理。结果表明：随着RE加入量的增加，热锻模具铸钢的磨损率先减后增，RE加入量在质量分数为0．05％时热锻模具铸钢具有最佳的高温磨损性能。RE变质热锻模其铸钢的高温耐磨性明最高于H13钢和3Cr2W8V钢。高温磨损机理为氧化磨损和氧化物的疲劳剥落，磨屑为块状的Fe2O3和Fe3O4。     

Scratch and Abrasion Resistant Coatings on Plastic Lenses—State of the Art,Current Developments and Perspectives

The manufacturing of ophthalmic lenses is one of the most important markets worldwide and, therefore, strong research efforts are undertaken to continuously improve the quality of the products, either silicate glasses or organic polymer lenses. Hybrid sol-gel based materials play a major role in this highly competitive field and have contributed significantly to the commercial success of the organic base materials. Recent developments concern fast curing and patternable coatings that might soon become part of this business. The compatibility of hybrid sol-gel materials either with organic dyes or with inorganic vacuum borne coatings offers further possibilities to develop highly sophisticated lenses meeting not only customer needs like perfect corrective function, high optical quality and protection, but also high durability as well as cosmetic and decorative aspects. An overview and a few recent developments are outlined below.     

Cu-P系稀土耐候钢中最佳稀土含量的研究

利用光学显微镜、图像分析仪和电子探针对低氧低硫的10PCuRE耐候钢板坯进行了观察和检测,采用干-湿周浸室内加速试验方法测得了试验钢的腐蚀率.用电化学方法测得了带锈样的阳极极化曲线.研究得出对于S:～0.004%,O:～0.002%的10PCuRE耐候钢,最佳稀土含量为0.0065%～0.012%,此稀土含量对非金属夹杂物的变质作用和耐蚀性能的提高最为有利.     

Resistance of supersulfated cement to strong sulfate solutions

One of the principal uses of supersulfated cement has been for structures exposed to sea water and sulfate bearing ground waters. The resistance to such environments has been related to the absence of calcium hydroxide and the combination of much of the free alumina into ettringite during hydration. This paper reports the resistance of SSC to sulfate solutions in which ettringite has been decomposed. Prism samples were subjected to initial water storage at 25°C for both 28 days and 6 months. Samples were also cured for 6 months at 95°C and at both 11% and 100% R.H. The control samples of 28 days were compared with the 6 months samples of a more mature undecomposed SSC paste. After curing the prisms were measured and all the samples were immersed in three sulfate solutions (0.7M Na₂SO₄ , 0.7M MgSO₄ and saturated CaSO₄), and water at the same time. Measurements of linear expansion over 6 months were carried out. Core and surface material following immersion was examined by DTG and XRD. The study indicated that SSC is resistant to sodium and calcium sulfate solutions. Strong magnesium sulfate solutions decomposed the samples under all conditions. A possible mechanism for this attack is suggested. This revised version was published online in July 2006 with corrections to the Cover Date.     

Influence of Some Aggressive Media on Corrosion Resistance of Mortars With Spent Cracking Catalyst

The influence of spent catalyst from catalytic cracking in fluidized bed on the hydration process of cement and the properties of cement mortars were studied. The spent catalyst was used as an additive to cement in the mortars (10 and 20% of cement). The samples of mortars kept in water for28 days, then they were placed in sulfate and chloride media for 2 months (the control samples were kept in water for 3 months). After this time they were subjected to bending strength and compressive strength determinations. Thermogravimetric and infrared absorption studies were performed and capillary elevation, capability of binding heavy metals, and changes in mass and apparent density were determined too. The studies disclosed the pozzolana nature of spent catalyst and its influence on cement mortars being in contact with corrosive media. This revised version was published online in August 2006 with corrections to the Cover Date.     

主动冷却点阵夹层防热结构温度响应计算模型北大核心CSCD

针对点阵夹层结构主动热防护问题,建立了夹层结构面板和芯体导热与冷却剂对流耦合的非稳态传热理论模型,利用有限体积法离散控制方程并在MATLAB中进行了迭代求解.模型首次考虑了面板与夹芯杆之间的收缩热阻,并利用分离变量法得到了收缩热阻的近似解析解.基于单胞模型和周期性边界条件,模拟得到了模型所需的表面对流传热系数h_(b)和h_(fin).最后,选取多单胞计算工况进行数值模拟和理论模型对比,并讨论了收缩热阻对模型预测精度的影响.结果表明:理论模型能够准确预测夹层结构及内部流体的温度变化,理论与仿真之间的最大误差不超过1%;随着外加热流密度不断增大,忽略收缩热阻使得计算结果造成的误差不断增大;与数值模拟相比,理论模型可显著地减少计算时间并节省计算资源,尤其适用于非均匀、非稳态复杂热载荷下点阵夹层结构的温度响应计算.     

Normalized Dynamic Characterization and Application of Multiple Heat Storage Materials Based on Standard Thermal Resistance北大核心CSCD

基于标准热阻和能量流法,推导出储热材料与换热流体的瞬态换热热阻,通过类比电路分析法,获得了储热-换热过程的瞬态热量流模型及动态响应时间常数。进一步引入节点温度,重新定义换热热阻,获得了储热与换热过程耦合的三阶电路瞬态热量流模型,求解得到了加热、储热和释热三类时间常数,可用于协同表征储热材料中储热与释热的快慢程度,从而实现了多类储热材料的归一化动态表征。通过数值模拟验证与应用对比分析,发现基于多时间常数的归一化动态模型用于表征储热材料的动态特性是可行的,可直接对不同换热、储热材料进行对比分析。案例分析发现与固体储热材料换热时,液态金属的动态换热能力优于熔融盐,而相比于水蒸气和CO₂,空气与陶瓷材料换热能更快达到稳态。     

钇提高YT14硬质合金耐磨性的机制

研究了不同Ｙ添加量对ＹＴ１４硬质合金显微组织、结构和耐磨性的影响。结果表明，在ＹＴ１４硬质合金中添加微量Ｙ，可显著提高合金的耐磨性。Ｙ的主要作用是均匀细化碳化物相和Ｃｏ相；提高Ｃｏ粘结相中Ｗ、Ｔｉ元素的固溶量及αＣｏ相所占的体积分数，从而提高Ｃｏ粘结相的强韧性；Ｙ在合金中形成Ｙ２ＷＯ６，表明Ｙ还可还原和清除碳化钨表面氧化膜，增强Ｃｏ粘结相与硬质相之间的结合强度     

Amino acid overproduction by analog resistant mutants of the nitrogen fixing cyanobacteriumAnabaena sp 287

Two amino acid analog resistant mutants of the cyanobacteriumAnabaena sp 287 were isolated after MNNG mutagenesis.Anabaena ST 16, a mutant resistant to the alanine analog D-α-aminobutyric acid andAnabaena ST 25, another mutant resistant to the histidine analog l,2,4-triazole-3-alanine, released alanine and histidine, respectively, into the medium upon immobilization in alginic acid during diazotrophic growth in fluidized bed reactors. The rates of amino acid production by the mutants were 4.3 μmol mg chl^-1 h^-1 of D-alanine byAnabaena ST 16 and 16.6 μnol mg chl^-1 h^-1 of L-histidine byAnabaena ST 25. Nitrogen fixation by the mutants was not affected by the extracellular amino acid concentration. While the radioactive carbon flow was followed, the parent strain retained 93% of fixed¹⁴C and released only 7% into the medium. On the other hand,Anabaena ST 16 released 13% andAnabaena ST 25 released 29% into the medium. These mutants are beneficial in the production of radioactive amino acids using diazotrophic photobiotechnology.     

Assessment of corrosion resistance of surface-coated galvanized steel by analysis of the AC impedance spectra measured on the salt-spray-tested specimen

In the present work, corrosion resistance of surface-coated galvanized steel was quantitatively determined by an analysis of the alternating current (AC) impedance spectra measured on the salt-spray-tested specimen. To evaluate the corrosion resistance of the surface-coated galvanized steel, AC impedance spectroscopy was performed on the salt-spray-tested specimen previously exposed to salt-sprayed corrosive environment. From the analysis of the impedance spectra, the area fraction transient of white rust θ ₂(t) was theoretically derived from the equivalent circuit equation by using two fitting parameters. The values of the two fitting parameters were determined by fitting the empirical transient equations to the area fraction of the resin coating layer and to the total resistance obtained from the impedance spectra measured, respectively. From the analyses of θ ₂(t) for four kinds of surface-coated galvanized steels with various resin coating layers, it is indicated that as the values of the two fitting parameters decrease in the order of CP, GI, OD and OM (commercial trade names) specimens, the corrosion resistance increases in that order as well. Furthermore, from the quantitative comparison of the two fitting parameters with the polarization resistance of the upper resin coating layer R _p determined from the potentiodynamic polarization curve, it is suggested that the two fitting parameters decrease in value as well with increasing R _p.