Characterization of chromate conversion coating on AA7075‐T6 aluminum alloy

Chromate conversion coatings (CCCs) on AA7075‐T6 were characterized using scanning electron microscopy, focused ion beam sectioning and scanning transmission electron microscopy with nano‐electron dispersive spectroscopy line profiling. The thickness and composition of the CCC was different at different locations on the heterogeneous microstructure of AA7075‐T6. The coating formed on the matrix phase was much thicker than that formed on the coarse Al–Cu–Mg, Al–Fe–Cu and Mg–Si intermetallic particles. Nano‐electron dispersive spectroscopy line profiling indicated that the coating on the Al–Fe–Cu particles was similar to the CCC formed on the phase matrix, primarily a chromium oxide. However, the coatings on the Al–Cu–Mg and Mg–Si particles were mixed Al/Mg/Cr oxide and Mg oxide, respectively. The growth of CCC followed a linear‐logarithmic kinetic rate law. The observations of this study support the sol‐gel model of CCC formation. Copyright © 2004 John Wiley & Sons, Ltd.     

Solid phase immune reactions as monitored by sedimentation field-flow fractionation

Summary Sedimentation field-flow fractionation was shown to permit the precise evaluation of surface concentrations of human IgG, adsorbed to polystyrene latex spheres of different sizes. Unlike conventional techniques for measuring protein uptake by colloidal substrates, this method allowed a direct evaluation of mass adsorbed per unit area, without the need for potentially destructive labelling reactions. Thus, a four hour adsorption of IgG from a 3–10 fold excess of protein in solution yielded surface concentrations which were 1.4±0.1 mg/m² on a 272 nm latex and 1.9±0.1 mg/m² on a latex with a diameter of 142 nm. The lower value coincided with the estimated monolayer surface coverage. The IgG-PS 272 nm adsorption complex was shown to take up negligible amounts of HSA from a 10 mg/mL solution, while its specific uptake of a polyclonal rabbit anti-human IgG was 2.6 molecules per molecule of adsorbed antigen. The same ratio was found for the smaller particles. The surface concentration of adsorbed second antibody, often crucial in immunodiagnostic quantifications, was therefore found to be significantly enhanced by the increased substrate curvature presented by the smaller particles.Dedicated to Professor Leslie S. Ettre on the occasion of his 70th birthday.     

Investigation of Glass-Like Sol-Gel Coatings for Corrosion Protection of Stainless Steel Against Liquid and Gaseous Attack

Glass-like sol-gel coatings have been investigated as corrosion protective coatings on stainless steel. Magnesium- and borosilicate coatings with thickness of about 100–700 nm and methyl-modified SiO2 coatings with a thickness of about 2 m were deposited on stainless steel plates by dip-coating. The coatings were densified between 400°C and 500°C in different atmospheres (N2, air) for 1 h. The corrosion protection against gaseous attack was investigated by accelerated corrosion tests, at 800°C in air for 1 h. A corrosion protection factor was calculated from the relation Fe/Fe2O3, determined by XRD on the surface of coated and uncoated samples. Methyl-modified SiO2 coatings showed a protection factor, which was 2 orders of magnitude higher than for the other coatings. Electrochemical investigations were performed on samples submerged in a NaCl solution for 200 h. The corrosion propagation, polarization resistance and impedance vector were measured. For accelerated corrosion tests, polarization intensity curves were determined for high potentials of up to 1 V. Again excellent results were obtained for the methyl-modified SiO2 coatings, which remained passive for 200 h. Results of the salt spray corrosion test, however, showed no corrosion protection by the sol-gel coatings. After 2000 h in the salt spray chamber the steel was corroded and the coatings peeled off. It is concluded that for the further development of these coatings an improved interfacial passivation will be required.     

Chiral stationary phases for LC and SFC obtained by “Polymer coating”

Summary Chirally substituted Si–H-containing polysiloxanes were synthesized, which can be immobilized on small particle silica gel as well as on the smooth surfaces of fused silica capillaries. Immobilization is achieved either by crosslinking or by chemical bonding to the surfaces via silanol groups; both reactions can only be performed by addition of H₂PtCl₆, which acts as catalyst for hydrosilylation and as stoichiometric reagent for crosslinking. Chiral substituents of systematically varied chemical structure were introduced into the polysiloxanes by hydrosilylation. The mechanism of immobilization was investigated by spectroscopic methods, notably²⁹Si-NMR. Homogenous stationary-phase coatings of variable film thickness and corresponding retentivity can easily be achieved. The enantioselectivity of the phase systems was characterized in dependency on the chemical structure of the chiral selectors attached to the polysiloxane chain of the chiral stationary phases and also in terms of the functional groups introduced into the solutes by derivatisation.     

Manipulation of the Electroosmotic Flow in Glass und PMMA Microchips with Respect to Specific Enzymatic Glucose Determinations

The determination of glucose in microfluidic chips made of glass or PMMA was used as a model for the combination of an enzymatic reaction with the separation of compounds. It was based on the enzymatic oxidation of glucose and the amperometric detection of hydrogen peroxide. Real samples frequently contain compounds, such as ascorbic acid, which may interfere with quantitative glucose determinations. Thus, electrophoretic separation of specific from unspecific signals was envisaged by applying electric fields which are also used to control the flow of liquid via electroosmotic effects. Surface charge densities of the capillaries influence the electroosmotic flow (EOF). They are dependent on the chip material and on the adsorption of components from the background electrolyte. Reversal of the EOF after addition of cetyltrimethylammonium bromide (CTAB) and an increase in EOF after addition of sodium dodecylsulfate (SDS) were observed at lower surfactant concentrations with the PMMA chips rather than with the glass chips. For both chip materials these concentrations were below the critical micelle concentration. Effective separation of H₂O₂ and ascorbic acid was achieved with low CTAB concentrations, which lead to a reduction, but not to a reversal of the EOF. Reversal of the EOF by higher CTAB concentrations or the increase in cathodic EOF by SDS accelerated ascorbic acid transportation and reduced the differences in migration times. Thus, for the specific determination of glucose, glucose oxidase was added together with low CTAB concentrations to the background electrolyte. This avoided interference from ascorbic acid, and data obtained from the analysis of fruit juices showed a good correlation to data obtained from a reference method.     

Sol-gel approach to in situ creation of high pH-resistant surface-bonded organic-inorganic hybrid zirconia coating for capillary microextraction (in-tube SPME)

A novel zirconia-based hybrid organic-inorganic sol-gel coating was developed for capillary microextraction (CME) (in-tube SPME). High degree of chemical inertness inherent in zirconia makes it very difficult to covalently bind a suitable organic ligand to its surface. In the present work, this problem was addressed from a sol-gel chemistry point of view. Principles of sol-gel chemistry were employed to chemically bind a hydroxy-terminated silicone polymer (polydimethyldiphenylsiloxane, PDMDPS) to a sol-gel zirconia network in the course of its evolution from a highly reactive alkoxide precursor undergoing controlled hydrolytic polycondensation reactions. A fused silica capillary was filled with a properly designed sol solution to allow for the sol-gel reactions to take place within the capillary for a predetermined period of time (typically 15-30 min). In the course of this process, a layer of the evolving hybrid organic-inorganic sol-gel polymer got chemically anchored to the silanol groups on the capillary inner walls via condensation reaction. At the end of this in-capillary residence time, the unbonded part of the sol solution was expelled from the capillary under helium pressure, leaving behind a chemically bonded sol-gel zirconia-PDMDPS coating on the inner walls. Polycyclic aromatic hydrocarbons, ketones, and aldehydes were efficiently extracted and preconcentrated from dilute aqueous samples using sol-gel zirconia-PDMDPS coated capillaries followed by thermal desorption and GC analysis of the extracted solutes. The newly developed sol-gel hybrid zirconia coatings demonstrated excellent pH stability, and retained the extraction characteristics intact even after continuous rinsing with a 0.1 M NaOH solution for 24 h. To our knowledge, this is the first report on the use of a sol-gel zirconia-based hybrid organic-inorganic coating as an extraction medium in solid phase microextraction (SPME).     

Free release static coating of glass capillary columns; Static coating at elevated pressure — Theoretical considerations and practice

Summary Static coating of glass capillary columns has hitherto solely been carried out by evaporation of the stationary phase solvents under vacuum conditions. However, since a solvent vapour pressure higher than the external pressure is the only requirement for the vapour to flow out of the column, evacuation should not be necessary. Several important factors in the static coating procedure, such as mass (solvent vapour) — and heat transfer, heat of vaporisation of the solvent and viscosity of the stationary phase solution at elevated temperature and outlet pressure are discussed, principally to rationalise an improved static coating procedure. The alternative, so-called free-release static coating procedure, was evaluated practically by coating several columns with OV-101 and SE-30. Coating speed was found to be rapid and relatively constant whereas coating efficiency was between 80 and 100%.     

Effect of solvent composition on free release static coating of capillary columns

Summary Three aspects with respect to the selection of solvents for static coating of capillary columns, i.e. coating speed, occurrence of bumping and solubility of stationary phases are discussed. Hypotheses are proposed in an attempt to explain the observed facts that mixed solvents result in much higher coating speeds than those obtained from pure solvents, that a proper choice of solvents together with a good and uniform deactivitation of the column inner wall is needed to prevent bumping. Stationary phase solubility vs. solvent composition is also briefly discussed.     

Separation of oligonucleotides and DNA fragments by capillary electrophoresis in dynamically and permanently coated capillaries,using a copolymer of acrylamide and β-D-glucopyranoside as a new low viscosity matrix with high sieving capacity

New copolymers of acrylamide and β-D -glucopyranoside were synthesized and characterized. The different reactivity of the two monomers towards radical polymerization meant we could control the growth of the polymer chains whose length was inversely related to the number of glucose residues incorporated in the copolymers. The properties of these polymers were investigated in the separation of oligonucleotides and double-stranded DNA by capillary electrophoresis (CE) in coated and uncoated capillaries. The new copolymers were a suitable matrix for CE due to their high-resolving capacity and low viscosity. We also looked into the advantages of a new method of dynamic suppression of electroosmotic flow based on the addition of small amounts (0.03–0.05%) of dimethylacrylamide to the sieving and to the running buffer. A complete test was run on the reproducibility and efficiency of separations carried out in a permanently and dynamically coated capillary, and the advantages and disadvantages of the two methods were compared.