An optimization method for designing SENSE imaging RF coil arrays

An optimization method in RF coil array design for SENSE imaging is described. Using this method the optimized RF coil geometries can be calculated numerically given the required SENSE imaging performance. Although this method can be applied to optimize the RF coil arrays for both 1D and 2D SENSE imaging, to demonstrate the potential applications of this method, we designed RF coil arrays for 2D SENSE imaging and compared their performance by simulation. An optimized 4-channel receive-only RF coil array designed for 2D SENSE imaging was implemented and tested to demonstrate the feasibility of the proposed technique. Imaging results showed reasonable agreement with the simulations, thus the method can be applied to RF coil array designs for SENSE imaging when optimum imaging performance is desired.     

复合材料柔软性对倒金字塔微结构阵列传感器性能的影响

采用模压成型方法制备了2种柔软性不同的热塑性聚氨酯/短切碳纤维/碳纳米管(TPU/SCF-CNT)复合材料复制物, 其表面上具有倒金字塔微结构阵列, 内部有SCF与CNT共同构成的导电通路. 将复合材料复制物和相应的复合材料平整片封装成柔性传感器. 结果表明, 压力作用下传感器内复制物和平整片之间的接触电阻因倒金字塔底棱的形变而显著降低. 对使用柔软性较高的复合材料封装的传感器, 虽然其相对迟滞稍大, 但压力作用下倒金字塔底棱形变量较大, 且复制物和平整片内导电通路增加量较大, 因此其在0~2.5 kPa的线性区内具有较高的灵敏度(0.32 kPa^?1). 制备的2种传感器均具有快速响应特性, 且能在500 s(约1580次)的循环压缩/释放测试(峰值压力约3 kPa)中保持较稳定的电阻响应. 研究表明, 利用模压成型的表面倒金字塔结构复合材料复制物封装成的柔性压力传感器具有良好的传感性能.     

Copper-cobalt-nickel oxide nanowire arrays on copper foams as self-standing anode materials for lithium ion batteries

Numerous scientists are in the pursuit of energy storage materials with high energy and high power density by assembly of electrochemically active materials into conductive scaffolds, owing to the emerging need for next-generation energy storage devices. In this architectures, the active materials bonded to the conductive scaffold can provide a robust and free-standing structure, which is crucial to the fabrication of materials with high gravimetric capacity. Thus, hierarchical copper-cobalt-nickel ternary oxide (CuCoNi-oxide) nanowire arrays grown from copper foam were successfully fabricated as free-standing anode materials for lithium ion batteries (LIBs). CuCoNi-oxide nanowire arrays could provide more active sites owing to the hyperbranched structure, leading to a better specific capacity of 1191 mAh/g, cycle performance of 73% retention in comparison to CuO nanowire structure, which exhibited a specific capacity of 1029 mAh/g and capacity retention of 43%, respectively.     

相控阵雷达导引头便携测试方法及误差角波动机理分析

相控阵雷达导引头组成复杂、测试指标多、数据量大,通常需要在符合远场条件的微波暗室内测试。本文介绍了一种相控阵雷达导引头便携测试方法及测试系统的组成,分析了便携测试机理、便携屏蔽装置设计原理,解释了该便携测试系统中相控阵雷达导引头角跟踪参数测试时偶尔引起的误差角波动现象。该测试方法简便、快捷、实用、成本低,较好的解决了外场或环境试验中产品测试的需求。本文所述相控阵雷达导引头便携测试方法和相关分析结论有较高的实用价值。     

基于ZigBee网络和超声定位的智能跟随小车

基于成熟的IEEE802.15.4协议和ZigBee无线模块,结合超声定位,设计了一种新颖的智能跟随系统。设计的核心为PIC18F4620单片机和MRF24J40MA无线收发模块,通过无线收发来完成节点间的识别与同步,同时以超声测距系统完成对被跟踪目标的定位,通过控制驱动电机动作实现对指定目标的定距离跟随。控制网络以子网的形式控制不同系统的分时定位跟随,同时管理各移动定位系统的入网和切换。样机测试结果表明系统达到了预期的跟随设计要求,具有一定的工程使用价值。     

基于光楔阵列产生光学涡旋阵列的研究

在研究光楔衍射法产生单涡旋的基础上,基于长条形光楔阵列,提出了利用光束阵列衍射产生涡旋阵列的方法.该方法要求光束阵列在平行于光楔边缘方向上的光束间距等于光束直径的整数倍.利用超精密机床采用一体化加工法加工了光楔阵列元件,验证了该方法的可行性.利用空间光调制器快速灵活调整光束阵列的优点,搭建了借助空间光调制器加载达曼光栅衍射产生所需光束阵列的实验光学系统.针对光束阵列与光楔阵列的匹配问题,研究了达曼光栅掩模图基本单元对光束阵列的调控,获得了可调结构的光束阵列.实验产生了拓扑荷一致的光学涡旋阵列,与仿真结果相一致,证明所提方法的有效性.     

Three‐Phase Barker Arrays

A 3‐phase Barker array is a matrix of third roots of unity for which all out‐of‐phase aperiodic autocorrelations have magnitude 0 or 1. The only known truly two‐dimensional 3‐phase Barker arrays have size 2 × 2 or 3 × 3. We use a mixture of combinatorial arguments and algebraic number theory to establish severe restrictions on the size of a 3‐phase Barker array when at least one of its dimensions is divisible by 3. In particular, there exists a double‐exponentially growing arithmetic function T such that no 3‐phase Barker array of size with exists for all . For example, , , and . When both dimensions are divisible by 3, the existence problem is settled completely: if a 3‐phase Barker array of size exists, then .     

1/f Noise QWIPs and nBn detectors

The low-frequency noise is a ubiquitous phenomenon and the spectral power density of this fluctuation process is inversely proportional to the frequency of the signal. We have measured the 1/f noise of a 640 × 512 pixel quantum well infrared photodetector (QWIP) focal plane array (FPA) with 6.2 μm peak wavelength. Our experimental observations show that this QWIP FPA’s 1/f noise corner frequency is about 0.1 mHz. With this kind of low frequency stability, QWIPs could unveil a new class of infrared applications that have never been imagined before. Furthermore, we present the results from a similar 1/f noise measurement of bulk InAsSb absorber (lattice matched to GaSb substrate) nBn detector array with 4.0 μm cutoff wavelength.     

Fabrication of type-II InAs/GaSb superlattice long-wavelength infrared focal plane arrays

In this paper, we present an InAs/GaSb type-II superlattice (SL) with the M-structure for the fabrication of a long-wavelength (10 μm range) infrared (LWIR) focal plane arrays (FPA), which are grown by molecular beam epitaxy (MBE). The M-structure is named for the shape of the band alignment while the AlSb layer is inserted into the GaSb layer of InAs/GaSb SL. A 320 × 256 LWIR FPA has been fabricated with low surface leakage and high R₀A product of FPA pixels by using anodic sulfide and SiO₂ physical passivation. Experiment results show that the devices passivated with anodic sulfide obviously have higher R₀A than the un-sulphurized one. The 50% cutoff wavelength of the LWIR FPA is 9.1 μm, and the R₀A is 224 Ω cm² with the average detectivity of 2.3 × 10¹⁰ cm Hz^1/2 W⁻¹.     

8×8APD阵列激光三维成像接收机研制

为了实现对目标的无扫描阵列激光三维成像并研究系统参数对三维成像距离分辨率的影响,研制了8×8 pixel激光三维成像接收机。接收机采用线性模式APD阵列,设计了模拟信号放大、阈值处理将回波光信号转换为数字信号后,利用FPGA设计实现64通道高精度阵列计时系统,实现了对目标的无扫描实时三维成像功能。首先对设计完成的三维成像接收机组成及成像原理进行了介绍,对三维成像接收机中APD探测器阵列信号的模拟处理和数字处理流程和实现方式进行了说明。随后分别对三维成像的核心FPGA计时系统及探测器整体进行了电子学测试和实验测试。测试结果表明,FPGA计时子系统的时间分辨率优于140 ps,三维成像系统整体距离分辨率在0.2 m左右。最后对分辨率的误差进行了分析,结果表明,激光回波强度波动是影响此接收机距离分辨率的最主要因素。