The electron microscope characterization of the fine structure of nylon 6: II. On the rearrangement of the structure during cold-drawing

The transmission electron microscope (TEM) visualization of the supermolecular structure of cold-drawn, oriented nylon 6 bulk material (bristles) by stained ultra-thin sections is reported. For evaluating the electron micrographs optical diffraction (OD) has been applied in comparison with small angle X-ray scattering (SAXS). The deformation of the spherulites was followed by polarization microscopy. In addition, investigations were carried out on commercial nylon 6 fibres. As the main result a transverse structure was revealed within the drawn samples at draw ratios between =4 and 4.5, consisting of mosaic crystals which show some lateral alignment. The structure is described by a modified layer lattice model. While the long period may increase slightly during drawing, the crystallite thickness remains almost constant. Fibres with =3.4 show a similarly oriented structure though the lateral alignment of the crystals is not so pronounced.     

Computational investigation toward selective collection of water particles containing odorous molecules by electrostatic spraying

The necessity of odor sensing has been increasing from environmental and health standpoints. Here, we propose the novel concept of a small device which can select odor molecules based on electrostatic spraying. For high selectivity of the target gas or odor, we conducted computational fluid dynamics coupled with an electrostatic field, as well as measurements by particle image velocimetry and anemometry. The computational model successfully reproduced characteristic features of ionic wind. Different trajectories of charged particles were computationally obtained owing to their electrical mobility. The results imply that different materials might be separated by the arrangement of the collecting electrode.     

Multiaxial mechanical behavior of aramid fibers and identification of skin/core structure from single fiber transverse compression testing

The transverse and longitudinal mechanical properties of aramid fibers like Kevlar? 29 (K29) fibers are strongly linked to their highly oriented structure. Mechanical characterization at the single fiber scale is challenging especially when the diameter is as small as 15 µm. Longitudinal tensile tests on single K29 fibers and single fiber transverse compression test (SFTCT) have been developed. Our approach consists of coupling morphological observations and mechanical experiments with SFTCT analysis by comparing analytical solutions and finite element modeling. New insights on the analysis of the transverse direction response are highlighted. Systematic loading/unloading compression tests enable to experimentally determine a transverse elastic limit. Taking account of the strong anisotropy of the fiber, the transverse mechanical response sheds light on a skin/core architecture. More importantly, results suggest that the skin of the fiber, typically representing a shell of one micrometer in thickness, has a transverse apparent modulus of 0.2 GPa. That is around more than fifteen times lower than the transverse modulus of 3.0 GPa in the core. By comparison, the measured longitudinal modulus is about 84 GPa. The stress distribution in the fiber is explored and the critical areas for damage initiation are discussed. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 374–384     

Evolution of downsized crescent-shaped dune in wind tunnel experiment

The migration of a downsized crescent-shaped dune was investigated in a wind tunnel experiment.Quantified upwind influx and vertical oscillation of the sand bed were introduced to modulate the saturation level of the sand flux above the dune surface to affect dune evolution.The evolution was recorded by top-view photography and then abstracted as the evolution of self-defined characteristic quantities using a digital image processing algorithm.The results showed that,in contrast to the case for spanwise quantities,the evolution of streamwise quantities corresponds to a linear increase in the modulation magnitude more positively and in a monotonic and convergent manner.In contrast with quantities on the windward face,the changes in quantities with respect to the horns were nonmonotonic with time and almost uncorrelated with the variation in modulation strength,which reveals the distinctiveness of leeside evolution.     

Control of a turbulent flow separated at mid-chord along an airfoil with DBD plasma actuators

The goal of the present experimental study is to investigate the ability of surface DBD plasma actuators to delay flow separation along the suction side of a NACA0015 airfoil. Three single surface DBD actuators that can operate separately are mounted on the suction side of the profile, at 18%, 27% and 37% of the chord length. The boundary layer is transitioned by a tripper to be sure that the flow control is not due to the laminar-to-turbulent transition. The angle of attack is equal to 11.5° and the free-stream velocity to U₀ = 40 m/s, resulting in a chord-based Reynolds number of Re_c = 1.33 × 10⁶. The flow is studied with a high-resolution PIV system. In such conditions, the baseline flow separation occurs at 50% of chord. Then, the different single DBD have been switched on separately, in order to investigate the actuator location effect. One highlights that the DBD located at x_c/c = 18% is more effective than the two others ones, with a separation delay up to 64% of chord. When the three DBDs operate simultaneously, the separation point moves progressively toward the trailing edge when the high voltage is increased, up to 76% of chord at 20 kV. Finally, the effect of the actuation frequency on the control authority has been investigated, by varying the value of the operating frequency and by burst-modulation. For frequencies equal to 50 Hz and 500 Hz (reduced frequency F⁺ = 0.31 and 3.1), the separation has been delayed at 76 and 80% of chord, respectively.     

Projectile fragment emission in the fragmentation of 56Fe on C,Al and CH2 targets at 471 A MeV

The emission angle and the transverse momentum distributions of projectile fragments produced in the fragmentation of 56Fe on CHs, C and A1 targets at 471 A MeV are measured. It is found that for the same target, the average value and width of the angular distribution decrease with an increase of the projectile fragment charge; for the same projectile fragment, the average value of the distribution increases and the width of the distribution decreases with increasing the target charge number. The transverse momentum distribution of a projectile fragment can be explained by a single Gaussian distribution and the averaged transverse momentum per nucleon decreases with the increase of the charge of projectile fragment. The cumulated squared transverse momentum distribution of a projectile fragment can be explained well by a single Rayleigh distribution. The temperature parameter of the emission source of the projectile fragment, calculated from the cumulated squared transverse momentum distribution, decreases with the increase of the size of the projectile fragment.     

Influence of surface and bulk layers on the crossover features for interaction parameters of a ferroelectric thin film

The phase diagram of a ferroelectric thin film is studied by using the usual mean-field approximation. The crossover features, from the ferroelectric-dominant phase diagram to the paraelectric-dominant phase diagram, for the physical parameters of the thin film are discussed. Special attention is devoted to the investigation of surface and bulk layers, and how to influence the crossover values of exchange interactions and transverse fields.     

大型砂尘风洞中砂尘浓度测量与控制方法的研究

砂尘浓度指标严重影响砂尘风洞试验效果;在大型砂尘风洞中准确的测量及有效的控制砂尘浓度是砂尘风洞设备研制中的两个关键问题;针对动态试验工况环境中浓度传感器标定的问题,分析了浓度测量时标定参数与风速和浓度的关系,使用模型树算法建立了三者之间的关系模型,以此模型来预测各种动态情况下的标定参数;针对复杂环境下浓度动态控制问题,采用专家PID算法,提出了多回路控制系统结构和专家规则;工程实践表明该测量和控制方法满足了动态试验环境的需求,取得了良好效果;模型树算法和专家PID系统能有效的解决动态工况下砂尘浓度的测量与控制问题。     

Artificial Caries Lesion Characteristics after Secondary Demineralization with Theobromine-Containing Protocol

Developing artificial caries lesions with varying characteristics is needed to adequately study caries process in vitro. The objective of this study was to investigate artificial caries lesion characteristics after secondary demineralization protocol containing theobromine and fluoride. Sixty bovine enamel slabs (4 × 3 mm) were demineralized using a Carbopol-containing protocol for 6 days. A baseline area (2 × 3 mm) was protected with acid-resistant nail varnish, after which specimens were exposed for 24 h to a secondary demineralization protocol containing acetic acid plus one of four fluoride/theobromine combinations (n = 15): theobromine (50 or 200 ppm) and fluoride (0 or 1 ppm). Specimens were sectioned and analyzed using transverse microradiography for changes in mineral content, lesion depth, and surface layer mineralization. Data was analyzed using paired t-test and analysis of variance followed by Bonferroni test at 0.05 significance level. After secondary demineralization, fluoride-containing groups had significantly deeper lesions (p = 0.002 and 0.014) compared to the group with 0 ppm fluoride and 50 ppm theobromine. Mineral content and lesion depth were significantly different compared to baseline for all groups. Theobromine did not show an added effect on mineral uptake. Theobromine-containing groups exhibited particularly deep lesions with a more uniform mineral profile in the presence of fluoride.     

Experimental Investigation of Natural Convection in Inclined Channel in Presence of Electrostatic Field

The influence of external electrohydrodynamic forces on natural convection from a flat plate has been studied. Temperature distribution in the aforementioned channel at α = 45°, 90°, and 150° angles in different 10-, 12-, and 15-kV electrostatic fields has been reviewed. Corona wind and the shape of the created vortex by electrohydrodynamics were detected. The results showed that heat transfer was enhanced by increasing the electrostatic field in all angles. In the presence of the field, enhancement of heat transfer of the plate at acute angles is better than for obtuse ones. The optimal angle in terms of heat transfer was 45°, noting heat transfer improvement by 61%.