面心立方晶体外延膜沉积生长中失配位错的结构与形成过程

用分子动力学方法对5%负失配条件下面心立方晶体铝薄膜的原子沉积外延生长进行了三维模拟.铝原子间的相互作用采用嵌入原子法(EAM)多体势计算.模拟结果再现了失配位错的形成现象.分析表明，失配位错在形成之初即呈现为Shockley扩展位错，即由两个伯格斯矢量为〈211〉/6的部分位错和其间的堆垛层错组成，两个部分位错的间距、即层错宽度为1.8 nm,与理论计算结果一致；外延晶体薄膜沉积生长中，位错对会发生滑移，但其间距保持稳定.进一步观察发现，该扩展位错产生于一种类似于“局部熔融-重结晶”的表层局部无序紊乱- 关键词： 失配位错 外延生长 薄膜 分子动力学 铝     

提高微晶硅薄膜太阳电池效率的研究

采用甚高频等离子体增强化学气相沉积技术制备了系列微晶硅薄膜太阳电池，指出了气体总流量和背反射电极的类型对电池性能参数的影响.电池的I-V测试结果表明：随反应气体总流量的增加，对应电池的短路电流密度、开路电压和填充因子都有很大程度的提高，结果使得电池的光电转换效率得以提高.另外，ZnO/Ag/Al背反射电极能明显提高电池的短路电流密度，进而也提高了电池的光电转换效率.对气体总流量和背反射电极类型影响电池效率的原因进行了分析. 关键词： 微晶硅薄膜太阳电池 气体流量 ZnO/Ag/Al背反射电极     

基于液晶光阀的全息照相控光仪

设计了通过液晶光阀自动调整全息照相物光和参考光辐照比至最佳状态,同时能实现曝光时间自动控制的控光仪.该仪器巧妙运用液晶光阀和硅光电池器件,使测量、调整、自控一体化,从而提高拍摄优质全息图的工作效率.     

两种方法制备ITO薄膜的红外特性分析

比较了用电束加热蒸发法和直流磁控溅射法制备的氧化锡铟(ITO)薄膜在红外波段的光学特性实验发现,通过直流磁控溅射在常温下制备的ITO薄膜在红外波段折射率稳定、消光系数小,比电子束加热蒸发制备的膜有较高的透过率在波长1550nm附近的透过率可达86%以上,消光系数约为004,方电阻最低为100Ω/□.     

混合判断矩阵排序方法研究

本文介绍了混合判断矩阵及完全一致性混合判断矩阵的概念，提出了混合判断矩阵排序的一种最小偏差法，并给出了其收敛性迭代算法，最后通过算例说明了方法的可行性。     

相变光盘介电薄膜ZnS-SiO2 的微结构和光学特性

采用射频磁控溅射法制备了ZnS-SiO₂ 介电薄膜,利用透射电镜和椭偏仪研究了溅射条件对ZnS-SiO₂薄膜微结构和折射率n的影响.研究表明,ZnS-SiO₂薄膜中存在微小晶粒,大小为2～10 nm的ZnS颗粒分布在SiO₂基体中,当溅射功率和溅射气压变化时,ZnS-SiO₂薄膜的微结构和折射率n发生显著变化,微结构的变化是导致折射率n变化的主要原因,通过优化溅射条件可以制备适用于相变光盘的高质量ZnS-SiO₂介电薄膜.     

U：CaF2晶体的分凝特性与光谱性质

应用TGT法生长了直径为75mm的U：CaF2晶体，宏观上透明完整.应用公式K0=Cs/Cl计算了U在CaF2晶体中的分凝系数等于0.53.应用溶质分布一般公式Cs=K0C0(1-g)K0-1，计算U的浓度分布与测量值，数值符合说明晶体生长过程接近平衡状态.分析不同条件下生长的U: CaF2晶体的晶胞参数和吸收光谱，结果表明生长气氛决定U的价态及电荷补偿机理：无PbF2存在的条件下，U为+4价，晶体呈绿色；PbF2的加入起到氟化去氧作用，U倾向于以离子半径最接近于Ca2+的U3+存在，晶体呈红色.从晶体生长开始到结束的部位，U3+:CaF2晶体吸收光谱的峰位不变，峰强呈现与U浓度相同的增加趋势.U3+:CaF2晶体外层厚约5mm处呈黄色，含有U3+和U2+的混合价态离子，其原理是石墨坩埚的还原作用通过单质铅，使部分的U3+进一步还原成了U2+. 关键词： 铀 氟化钙晶体 分凝系数 晶胞参数     

Naphthyl azomesogens with lateral chloro groups

A homologous series of azomesogens, 2″-[4-(4′-n-alkoxybenzoyloxy)-2-chlorophenylazo] naphthalenes, with lateral chloro groups was synthesised. All the homologues synthesized exhibit enantiotropic nematic mesophase. The mesomorphic properties of the present series are compared with other structurally related series to evaluate the effect of lateral chloro group and its position on mesomorphism This paper was presented at the 10th National Conference on Liquid Crystals held at Bangalore, India during 9–11 October 2003.     

The Analysis and Improving of the Microwave Exciter in the Lower Hybrid Wave System

When we carry out lower hybrid wave heating and current driving plasma experiment at tokamak, we need mega-watt order of microwave power. The microwave signal at frequency of 2450 MHz is generated by a microwave exciter. According to the experiment＇s demands, the microwave exciter must provide output power of 1.5～ 2. 5 W with stabilized frequency and amplitude tobe used as the klystron input. Being amplified by the klystron, the microwave signal is transmitted through the transmitting system to the antenna and is emitted into the HL-2A tokamak. So we can see that the microwave exciter＇s function is very important to the lower hybrid wave heating and current driving plasma experiment.     

Decreasing the Displacements of a Composite Saddle-Shaped Cable Roof

The structural possibilities of decreasing the compliance of a composite saddle-shaped cable roof having a compliant support contour are investigated. The use of a supporting contour consisting of cables joined together with tie-bars is considered as a structural method enabling one to decrease the compliance of the roof. Each cable of the support has its own initial flexure. The method is most efficient from the viewpoint of material consumption per unit of covered area relative to the increasing rigidity and prestress level of the cable net.The efficiency of the method was evaluated by a numerical experiment, which was carried out for a composite saddle-shaped cable roof 50 × 50 m in the plan. The roof was formed by two orthogonal cable groups joined with a compliant supporting contour. A hybrid composite cable based on a carbon-fiber-reinforced plastic, a glass-fiber-reinforced plastic, and steel was considered as a material for the cable net in combination with steel. The material consumption and the maximum vertical displacement of the cable net in relation to the initial geometrical characteristics of the supporting contour were obtained. A possibility of decreasing the maximum vertical displacements of the roof by 8% was established.