Advances of phononics in 2012—2022

Due to its great potential applications in thermal management, heat control, and quantum information, phononics has gained increasing attentions since the first publication in Rev. Mod. Phys. 84 1045 (2012). Many theoretical and experimental progresses have been achieved in the past decade. In this paper, we first give a critical review of the progress in thermal diodes and transistors, especially in classical regime. Then, we give a brief introduction to the new developing research directions such as topological phononics and quantum phononics. In the third part, we discuss the potential applications. Last but not least, we point out the outlook and challenges ahead.     

Bi-Sb-Te基热电薄膜温差电池离子束溅射制备与表征

本文采用离子束溅射Bi/Te和Sb/Te二元复合靶,直接制备n型Bi₂Te₃热电薄膜和p型Sb₂Te₃热电薄膜.在退火时间同为1 h的条件下,对所制备的Bi₂Te₃薄膜和Sb₂Te₃薄膜进行不同温度的退火处理,并对其热电性能进行表征.结果表明,在退火温度为150 ℃时,制备的n型Bi₂Te₃关键词： 薄膜温差电池 2Te₃薄膜')" href="#">Sb₂Te₃薄膜 2Te₃薄膜')" href="#">Bi₂Te₃薄膜 离子束溅射     

Effect of dispersion degree of orientation on dielectric properties of (100)-oriented PST thin film

(100) Oriented (Pb_xSr_1−x)TiO₃ (PST) thin films were prepared on indium tin oxide coated glass substrates by sol–gel technique with rapid thermal processing. The dielectric permittivity and tunability of the thin films with different dispersion degrees of orientation were investigated in detail by characterizing the full width at half maximum of their (100) peak based on rocking curves at different annealing temperatures. Influence of orientation dispersion on dielectric properties was exhibited in the tunable dielectric thin films. It shows that the dielectric constant and hence the tunability of the sol–gel derived PST thin films are improved with the decrease in the dispersion degree of orientation of the perovskite phase other than the increase in the content of crystalline phase in the thin films. The dielectric constant (capacitance) and figure of merit of the oriented thin films are 3–6 times and 1 times higher than that of randomly oriented thin film respectively.     

Atmospheric pressure chemical vapour deposition of fluorine‐doped tin(IV) oxide from fluoroalkyltin precursors

Perfluoroalkytin compounds R_(4−n)Sn(R_f)_n (R = Me, Et, Bu, R_f = C₄F₉, n = 1; R = Bu, R_f = C₄F₉, n = 2, 3; R = Bu, R_f = C₆F₁₃, n = 1) have been synthesized, characterized by ¹H, ¹³C, ¹⁹F and ¹¹⁹Sn NMR, and evaluated as precursors for the atmospheric pressure chemical vapour deposition of fluorine‐doped SnO₂ thin films. All precursors were sufficiently volatile in the range 84–136 °C and glass substrate temperatures of ca 550 °C to yield high‐quality films with ca 0.79–2.02% fluorine incorporation, save for Bu₃SnC₆F₁₃, which incorporated <0.05% fluorine. Films were characterized by X‐ray diffraction, scanning electron microscopy, thickness, haze, emissivity, and sheet resistance. The fastest growth rates and highest quality films were obtained from Et₃SnC₄F₉. An electron diffraction study of Me₃SnC₄F₉ revealed four conformations, of which only the two of lowest abundance showed close F Sn contacts that could plausibly be associated with halogen transfer to tin, and in each case it was fluorine attached to either the γ‐ or δ‐carbon atoms of the R_f chain. Copyright © 2005 John Wiley & Sons, Ltd.     

Development of superconducting power devices in Europe

Europe celebrated last year (2008) the 100-year anniversary of the first liquefaction of helium by H. Kammerling Onnes in Leiden. It led to the discovery of superconductivity in 1911. Europe is still active in the development of superconducting (SC) devices. The discovery of high critical temperature materials in 1986, again in Europe, has opened a lot of opportunities for SC devices by broking the 4 K cryogenic bottleneck.     

Molecular organization in MAPLE‐deposited conjugated polymer thin films and the implications for carrier transport characteristics

The morphological structure of poly(3‐hexylthiophene) (P3HT) thin films deposited by both Matrix Assisted Pulsed Laser Evaporation (MAPLE) and solution spin‐casting methods are investigated. The MAPLE samples possessed a higher degree of disorder, with random orientations of polymer crystallites along the side‐chain stacking, π–π stacking, and conjugated backbone directions. Moreover, the average molecular orientations and relative degrees of crystallinity of MAPLE‐deposited polymer films are insensitive to the chemistries of the substrates onto which they were deposited; this is in stark contrast to the films prepared by the conventional spin‐casting technique. Despite the seemingly unfavorable molecular orientations and the highly disordered morphologies, the in‐plane charge carrier transport characteristics of the MAPLE samples are comparable to those of spin‐cast samples, exhibiting similar transport activation energies (56 vs. 54 meV) to those reported in the literature for high mobility polymers. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 39–48     

Pretilt study of double‐layer alignment film (DLAF)

A novel double‐layer alignment film (DLAF) was developed to obtain greater control of the alignment characteristics of the liquid crystal director. The DLAF consists of a thin fluorinated polymer layer on the top of a rubbed non‐fluorinated, non‐branched polyimide layer (PI 2555). Two types of fluorinated polymer with different chemical structures and wetting behaviour on PI 2555 were chosen, to provide either continuous or discontinuous top layers. The continuous top layer DLAF (DLAF‐1) exhibits an abrupt pretilt transition from planar to homeotropic as the top layer thickness increases. The discontinuous top layer DLAF (DLAF‐2) exhibits a gradual transition where the pretilt correlates with the coverage of fluorinated top layer. These two types of transitions fit with de Gennes' local Frederick's transition and Kwok's inhomogeneous alignment theories, respectively. The abrupt pretilt transition system may be promising for chemical/biosensor applications, whereas the gradual transition system is suitable for pretilt control in LCD devices.     

Zur Methodik der Autoradiographie im Elektronenmikroskop

Die elektronenmikroskopische Autoradiographie erlaubt unter Ausmutzung des hohen Auflösungsvermögens des Elektronenmikroskops eine exakte Lokalisierung radioaktiver Verbindungen in Präparaten. Voraussetzung dafür ist die Herstellung einer Einkornschicht des Silberhalogenids aus einer vorgegebenen Filmemulsion. Diese Einkornschicht mit möglichst gleichmäßiger Silberhalogenidverteilung muß dann auf das radioaktive Objekt aufgebracht werden. Nach einer Übersicht über die Versuchsmethode werden Untersuchungen zur Präparation von Silberhalogenid-Einkornschichten aus den Emulsionen ORWO K 2, K 5, K 6, Ilford L 4 und Gevaert Nuc 7.15 für die elektronenmikroskopische Autoradiographie dargestellt.     

Towards Dynamic Control of Wettability by Using Functionalized Altitudinal Molecular Motors on Solid Surfaces

We report the synthesis of altitudinal molecular motors that contain functional groups in their rotor part. In an approach to achieve dynamic control over the properties of solid surfaces, a hydrophobic perfluorobutyl chain and a relatively hydrophilic cyano group were introduced to the rotor part of the motors. Molecular motors were attached to quartz surfaces by using interfacial 1,3‐dipolar cycloadditions. To test the effect of the functional groups on the rotary motion, photochemical and thermal isomerization studies of the motors were performed both in solution and when attached to the surface. We found that the substituents have no significant effect on the thermal and photochemical processes, and the functionalized motors preserved their rotary function both in solution and on a quartz surface. Preliminary results on the influence of the functional groups on surface wettability are also described.