复合多层介质在可变温度和集中荷载作用下的位移和应力

研究了多层介质中的热弹性位移和应力.多层介质具有不同厚度,各层又具有不同的弹性性质,最上层表面上作用热荷载和集中荷载.假设各层分别是均匀、各向同性弹性材料,各层相关的位移分量是轴对称的,对称轴为各层表面的垂线.因此,各层应力函数满足无体力的单一方程.利用积分变换法求解了该方程,对由任意多个层数构造的多层介质,给出了其相应层数基础热弹性位移和应力的解析表达式.并对3层介质和4层介质时的数值结果进行了比较.     

热动力学问题的数值计算

 对含热传导的流体动力学方程组，用有限元方法进行数值求解。采用傅里叶热传导计算热流、用热流连续条件计算单元间接触面的温度、用三角形传热法计算体单元表面的热流，考虑各向同性弹塑性流体材料模型、三项式物态方程和导热系数与状态的相关性，给出了傅里叶热传导、接触传热、热应力应变效应、以及混合物冲击压缩特性等算例。对混合物冲击温度的数值模拟表明，小颗粒混合物在冲击压缩过程中，颗粒间的温度有差别、稍有波动，并随时间趋向于一致，以至热平衡。     

服装主观热感觉的统计分析

本文用多因子方差分析模型和多重比较分析了服装穿着时的主观热感觉与服装品种、环境条件、穿着者的活动状态与籍贯之间的关系。通过主成分回归建立了用生理指标预测主观热感觉的模型，从而得出一种定量地评价服装属性的方法。     

Intrinsic thermal stability and quenching recovery of thin-film superconductors with thermal boundary resistance

The stability behaviour of a thin-film superconductor under a localized release of thermal disturbance is investigated. Two-dimensional conjugate film/substrate conduction equation with anisotropic thermal conductivity of the film, and Joule heat are employed to investigate effects of substrate and thermal properties on the intrinsic stability and quenching recovery. To consider the thermal boundary resistance between film and substrate, an interfacial-layer model (ILM) with very low diffusivity and an acoustic mismatch model (AMM) are employed. Results show that the thermal boundary resistance influences strongly the intrinsic stability. Thermal boundary resistance increases intrinsic stability if the thermal conductivity of the substrate or the disturbance energy is large. Higher Biot numbers and thermal conductivity ratios of film to substrate in longitudinal direction influence stability favorably. We demonstrate also that operation of a film/substrate system, such as YBCO/MgO, is either intrinsically stable or irrecoverably unstable.The authors wish to express their sincere appreciation to Dr. R. C. Chen for his invaluable advice and suggestions during the course of this paper. This research was supported by the National Science Council of the R. O. C. through grant NSC 83-0401-E-009-006. The computations were performed on the IBM ES/9000 at the National Center For High-Performance Computing.     

Ageing of wet-synthesized oxide powders

Wet chemical synthesis of precursor oxide ceramics is a method to obtain small particulate powders. Such powders are far more prone to ageing in air than more traditional precursors. Thermogravimetric analysis is used to highlight the species responsible for the ageing of ceramic precursors. Indeed water and carbon dioxide are observed to evolve from aged powders. Ceramics obtained from aged precursors can reach a very low final density with respect to the theoretical value. A large degree of the original sintering properties can be recovered after washing the aged powders with ethanol in a basic medium.     

Graphitic nanofillers in PMMA nanocomposites—An investigation of particle size and dispersion and their influence on nanocomposite properties

Mechanical, thermal, and electrical properties of graphite/PMMA composites have been evaluated as functions of particle size and dispersion of the graphitic nanofiller components via the use of three different graphitic nanofillers: “as received graphite” (ARG), “expanded graphite,” (EG) and “graphite nanoplatelets” (GNPs) EG, a graphitic materials with much lower density than ARG, was prepared from ARG flakes via an acid intercalation and thermal expansion. Subsequent sonication of EG in a liquid yielded GNPs as thin stacks of graphitic platelets with thicknesses of ～10 nm. Solution‐based processing was used to prepare PMMA composites with these three fillers. Dynamic mechanical analysis, thermal analysis, and electrical impedance measurements were carried out on the resulting composites, demonstrating that reduced particle size, high surface area, and increased surface roughness can significantly alter the graphite/polymer interface and enhance the mechanical, thermal, and electrical properties of the polymer matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2097–2112, 2007     

Gas solubility of carbon dioxide in poly(lactic acid) at high pressures: Thermal treatment effect

The sorption of carbon dioxide in glassy Poly(lactic acid) (PLA) films was studied by quartz crystal microbalance (QCM) at high pressures. Two thermal treatments, melted and quenched, were performed in PLA with two different L:D contents, 80:20 and 98:2, films and compared with a third thermal protocol, annealed, and used in a previous work. The results obtained show that for pressures higher than 2 MPa, the carbon dioxide solubility is larger in PLA 80:20 than in PLA 98:2, indicating that the L:D plays a dominant role on this property. The thermal treatments only affect the gas solubility in PLA 98:2. Sorption isotherms at temperatures 303, 313, and 323 K, below the glass transition temperature of the polymer, and pressures up to 5 MPa were measured and analyzed with three different models, the dual‐mode sorption model, the Flory–Huggins equation, and a modified dual‐mode sorption model where the Henry's law term was substituted by the Flory–Huggins equation. This last model performs especially well for CO₂ in PLA 80:20, due to the convex upward curvature of the solubility isotherms for that system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 616–625, 2007     

LD端抽运平直腔Nd:YVO4固态激光器的输出功率特性研究

对LD端抽运平直腔Nd:YVO₄固态激光器输出功率特性受激光器内在诸因素(热透镜效应、腔长、激活孔径等)的制约关系进行了研究.并用传播圆-变换圆图解分析方法给出了合理的解释，同时，对进一步提高其输出功率特性指出了方向. 关键词： 固体激光器 热透镜 变换圆 平直腔     

激光介质的多次吸收不均匀内热源模型

针对激光介质的内热源,以多次吸收作用为基础提出了适用于侧面双向泵浦板状激光介质的不均匀内热源模型,即多次吸收不均匀内热源模型,并与均匀内热源和一次吸收内热源模型进行了对比分析。研究表明,介质厚度及光吸收系数组成的无量纲参数不同时,三种内热源模型得到的内热源分布也有所不同。最后给出了内热源不均匀度及多次吸收模型与一次吸收模型之间的差异在不同目标值下的内热源模型适用准则。