位错偶极子和Ⅲ型界面裂纹的干涉效应

研究了多晶体材料中螺型位错偶极子和界面裂纹的弹性干涉作用.利用复变函数方法,得到了该问题复势函数的封闭形式解答.求出了由位错偶极子诱导的应力场和裂纹尖端应力强度应子,分析了偶极子的方向,偶臂和位置以及材料失配对应力强度因子的影响.推导了作用在螺型位错偶极子中心的像力和力偶矩,并讨论了界面裂纹几何条件和不同材料特征组合对位错偶极子平衡位置的影响规律.结果表明,裂纹尖端的螺型位错偶极子对应力强度因子会产生强烈的屏蔽或反屏蔽效应.同时,界面裂纹对螺型位错偶极子在材料中运动有很强的扰动作用.     

STUDY ON THE PROPERTIES OF BLEND OF NATURAL RUBBER LATEX/METHYL METHACRYLATE GRAFTED RUBBER LATEX BY GAMMA RADIATION

Natural rubber latex(NRL)and methyl methacrylate(MMA)grafted rubber latex were blended in different ratios and irradiated at various absorbed doses by gamma rays from Co-60 source at room temperature.The tensile properties, swelling ratio and permanent set were measured.The maximum tensile strength and modulus at 500% elongation were obtained at an absorbed dose of 8 kGy.Modulus increases from 6.99 MPa to 9.87 MPa for an increase in proportion of MMA grafted rubber from 40% to 60% in the blend at similar absorbed dose.Elongation at break and swelling ratio decrease with increasing absorbed dose as well as the MMA grafted rubber content in the blends.The decreasing trend of permanent set is high up to 5 kGy absorbed dose,and beyond that dose,it becomes almost flat.     

基于紧凑拉伸剪切结构的复合型疲劳裂纹扩展研究

针对含I-II型复合裂纹的紧凑拉伸剪切(CTS)试样,研究了不同加载角度下的裂纹扩展路径及裂纹扩展寿命,通过实验数据给出了适宜于CTS试样的等效应力强度因子关系式,并基于此提出了一种新的I-II型复合裂纹扩展模型。研究表明,CTS试样的裂纹沿与加载方向近垂直的方向扩展,基于Tanaka公式的等效应力强度因子更适合于本文CTS试件的裂纹扩展寿命评估。当加载角度处于0°~45°之间时,提出的复合型裂纹扩展模型预测误差控制在5.49%之内,验证了分析模型的可行性和准确性。     

变温下橡胶材料力学性能的实验分析

利用Zwick020材料试验机研究了天然橡胶材料在不同温度条件下单向拉伸的大变形力学行为。得到了不同温度和不同加载速率条件下材料的应力-应变关系曲线和材料的破坏条件,由此分析了高温和低温的温度变化条件及加载速率对材料力学性能的影响,得出天然橡胶材料在大变形条件下的温度和加载速率敏感特性。同时利用实验结果拟合出材料的应变能函数,并应用热超弹性模型对材料进行了理论分析。结果表明,理论分析结果与实验结果仅在一定温度范围内吻合得较好,因为材料软化或硬化,在很高或很低的温度情况下二者有一定差别。     

Nanoporous polyimide film from poly(ethylene glycol-co-imide) using a one-step heat calcination process

Polyamic acid (PAA) made from 3,3, 4,4-biphenyltetracarboxylic dianhydride and 4,4-diaminodiphenyl ether was synthesized and used as the backbone of nanoporous polyimide. Thermally labile polyethylene glycol (PEG) at 10, 20 or 30 wt% was introduced to the end group of PAA. Self-assembled PAA-b-PEG micelle-like nanoparticles could be formed as a result of amphiphilic characteristics of hydrophobic PAA and hydrophilic PEG. Thermal imidization and degradation of spin-coated amphiphilic PAA-b-PEG film were performed sequentially through one-step heat treatment to obtain polyimide film with nanopores. Pore sizes decreased with increasing amount of PEG block and their dielectric constants decreased from 2.71 ± 0.13 to 2.38 ± 0.11.     

Hamilton-Poisson formulation for the rotational motion of a rigid body in the presence of an axisymmetric force field and a gyroscopic torque

We give sufficient conditions for the rigid body in the presence of an axisymmetric force field and a gyroscopic torque to admit a Hamilton-Poisson formulation. Even if by adding a gyroscopic torque we initially lose one of the conserved Casimirs, we recover another conservation law as a Casimir function for a modified Poisson structure. We apply this frame to several well-known results in the literature.     

单晶ZnO、TiO_2纳米线拉伸力学特性的分子动力学研究

采用分子动力学方法,模拟了不同加载速度、不同温度下单晶ZnO、TiO_2纳米线的拉伸破坏过程.通过模拟结果,对比、分析了两种单晶金属氧化物纳米线拉伸力学特性的差异.研究表明,1)ZnO纳米线的断裂机制为:表面微裂纹-微孔-微裂纹与微孔贯穿-断裂,而TiO_2纳米线的断裂机制为:局部屈服-颈缩-断裂;2)TiO_2纳米线的承载能力优于ZnO纳米线,而承受变形的能力劣于ZnO纳米线;3)温度较低的情况下,纳米线的抗拉性能较好;加载速度越高,纳米线的抗载性能越好,而抗变形能力越差.     

Rotation rate of a three-wing rotor illuminated by upward-directed focused beam in optical tweezers

The optical torque and the trapping position (focal point) in optical tweezers are analyzed for upward-directed focused laser illumination using a ray optics model, considering that laser light is incident at not only the lower surface but also the side surface of a 3-wing rotor. The viscous drag force due to the pressure and the shearing stress on all surfaces of the rotor is evaluated using computational fluid dynamics. The rotation rate is simulated in water by balancing the optical torque with the drag force, resulting in 500 rpm for an SU-8 rotor with 20 μm diameter at a laser power of 200 mW. The trapping position is estimated to be 7.6 μm in the rotor with an upward-directed laser at 200 mW via an objective lens having a numerical aperture of 1.4. Both the rotation rate and the trapping position agree well with the values obtained in the experiment.     

Phase behavior,morphology, and mechanical properties of polyethylene-copolymer blends

Binary blends of unbranched polyethylene (PE) and 5-10% model ethylene-butene random copolymers are used to determine the effects of composition heterogeneity on phase separation in the melt, semicrystalline morphology, plane strain fracture toughness J_C and tensile modulus and yield strength. Slowly cooled samples of melt-miscible blends are appreciably tougher (J_C = 5.2 kJ/m²) than unblended PE (J_C = 2.7 kJ/m²). A blend with the same average short chain branch concentration, but which is phase separated in the melt state, has J_C= 3.3 kJ/m²; dispersed domains of amorphous polymer have little effect on toughness. Enhanced toughness is associated with nonuniform morphology formed on slow cooling “one phase” melts composed of chains with different amounts of branching. The relative number of chemically different chains, as opposed to absolute branch concentrations, seems most important. Tensile properties are relatively unaffected by blending at these levels. Results from these model blends are used to consider the properties of compositionally heterogeneous ethylene copolymers. © 1994 John Wiley & Sons, Inc.