Non-stoichiometry of YBa2Cu3O7-d Observed by Repeated Temperature Scanning

Repeated temperature scanning method was applied to observe non-stoichiometry of YBa₂Cu₃O₇-d, and interesting results were obtained. Two simultaneously occurring processes were separately observed in mass change; one is a fast process and the other is slow, so that their responses to the temperature change are quite different from each other. The fast process follows the cyclic temperature change, but the slow process is observed to be a gradual mass change. Kinetic behaviors of these two processes are also made clear by plotting the mass vs. the temperature. Furthermore, a hysteresis loop was observed in the plot of the mass vs. the temperature in a high temperature range presumably due to the third process, and it depends on the heating and cooling rates. This revised version was published online in July 2006 with corrections to the Cover Date.     

温度对贮氢合金MlNi3.75Co0.65Mn0.4Al0.2动力学性能的影响

在-20℃～85℃的范围内系统地研究了温度对贮氢合金MINi3.75Co0.65Mn0.4Al0.2动力学性能的影响.结果表明:该贮氢合金电极的电化学反应电阻Rt,欧姆内阻Ro,阴极极化过电位,阳极极化过电位,阳极极化过程中的电化学反应过电位ηa和浓差极化过电位ηa均随温度的升高而减小,该电极的交换电流密度i0,对称因子β和电极中氢的扩散系数D随温度的升高而增大.当放电电流密度较低时,电化学反应是整个电极过程的速度控制步骤;当放电电流密度较高时,氢的扩散是整个电极过程的速度控制步骤;在中等放电电流密度下,电极过程由电化学过程和氢的扩散过程混合控制.该电极中电化学反应过程和氢扩散过程的活化能分别为28.1 kJ·mol-1和19.9 kJ·mol-1.     

过渡金属对分子筛担载Pd催化剂上CO氧化性能影响

分别采用共浸和连续浸渍法制备了一系列添加过渡金属的Pd-M-Ox-NaZSM-5(M=Cr，Mn，Fe，Co，Ni，Cu，Zn，Mo，Zr等)负载型催化剂．以CO氧化为探针反应，考察了不同制备方法对CO氧化性能影响，结果表明共浸法制备的各催化剂其活性明显优于连续浸渍法．详细考察了反应温度、Fe含量、氢气预还原、空速以及水蒸气等对共浸Pd-Fe-Ox-NaZSM-5催化剂上CO氧化行为影响，并应用XRD和XPS等手段对催化剂体相结构和表面状态进行了表征．结果表明：加入Fe2O3可明显提高Pd/NaZSM-5催化剂活性，且催化CO氧化的转化率随反应温度及Fe含量增加而增加；空速增加以及H2预还原作用导致Pd-Fe-Ox-NaZSM-5活性有所降低；催化剂对水蒸气较为敏感．XRD测试结果表明催化剂中Pd组分处于较高分散状态，以红铁矿形式存在的Fe2O3的引入，促进了Pd物种在NaZSM-5载体上的分散．表面XPS分析证实Fe2O3与Pd物种间存在较强的相互协同作用，且催化剂表面Pd物种处于较高氧化状态．Pd的高分散及其与Fe2O3的相互协同作用是共浸催化剂具有高活性的关键因素．     

Temperature measurements by H2-CARS in the reactive zone of a plasma test reactor for hydrocarbon synthesis

The application of coherent anti-Stokes Raman spectroscopy (CARS) to an electric are test reactor is described in which acetylene synthesis in analogy to the large-scale industrial process is .studied. We report on spatially resolved measurements of H₂-CARS spectra, the comparison with calculated spectra, and the determination of temperatures in the reaction zone.Dedicated to Prof. Rudolf Wienecke on the occasion of his 65 birthday.     

无保护流体室温燐光法测定吲哚-3-丁酸的研究

在仅以碘化钾为重原子微扰剂、亚硫酸钠为除氧剂及无任何保护性介质存在的水溶液中 ,吲哚_3_丁酸 (IBA)能发射很强的室温光 (RTP) ;详细研究了分析测定条件及有机溶剂对RTP的影响 ;在最大光波长λex/λem =281/447nm处 ,光强度与IBA浓度在2.0×10 -7～1.0×10 -5mol/L范围内呈良好的线性关系 ,检出限4.3×10-8 mol/L ;方法直接用于强化水样和土壤中IBA的测定 ,回收率96 %～104 % ,相对标准偏差2.37 %～3.97 %。     

低温燐光的研究及应用

本文综述了44篇文献,介绍低温燐光的发展概况及其应用。     

Room Temperature Solid State Reaction Involving Structural Transformation of Covalent Oxide Network

An interesting structural transformation from a two dimensional (2d) covalent oxide network with a layered structure to a three-dimensional (3d) network with a tunnel structure was found at room temperature in the mixture of hydrated alkali-metal molybdenum bronze and amorphous alkali-metal molybdate. From various experimental results it was concluded that the transformation was due to a room temperature solid state reaction.     

Unusual features of micellar diffusion

Diffusion coefficients of tetradecyltrimethylammonium bromide in aqueous solutions have been determined at 25, 95 and 135 °C using the Taylor dispersion technique. The diffusion coefficient exhibits a minimum at a surfactant concentration above the critical micelle concentration (CMC). The results are interpreted in terms of electrostatic coupling and rapid exchange between micelle, surfactant monomer and counterions.     

Self-strengthening and high temperature sintering in binder-free silicon nitride

A thermal strengthening process, which occurs during low-temperature heating of binder-free silicon nitride, has been investigated using simultaneous thermal analysis, dilatometry and FTIR and shown to occur in separate stages over clearly identifiable temperatures. Reactions which give the strengthening are the loss of physically and chemically combined water and the decomposition of ammonium carbonate and various hydrosilicates. Compacts have bend strengths of 8–10 MPa after strengthening at 500°C and 30–34 MPa after strengthening at 900°C. High-temperature dilatometry shows several stages of sintering. The maximum rate occurs at 1800°C with shrinkage commencing at 1450°C. Densities of 98.3% theoretical are obtained on heating to 1900°C.     

Evaluation of the calibration errors on cooling of a differential scanning calorimeter using different sets of standard metals

The temperature calibration on cooling of thermal analysis instruments is important for the accurate study of the non-isothermal crystallization kinetics of semi-crystalline polymers. In previous works, a methodology was proposed for performing the calibration on cooling of differential scanning calorimeters (DSCs) with standard metals, and the calibration errors were checked using transitions of high-purity liquid crystals. In this work, alternative, physically meaningful, procedures for carrying out the calibration on cooling are analyzed and validated. The calibration errors are evaluated also with liquid crystalline transitions, when the calibration is performed with standard metals, in a wide temperature range, and when due account is taken for the need of isothermal corrections to the temperature measurements. It is shown that any pair of standard metals may be used to calibrate on cooling, that the calibration errors increase for wider working temperature ranges and that, providing that certain conditions are fulfilled, both calibration procedures yield similar results.