基于低相干光的阵列透镜束匀滑技术研究

基于激光加载的材料状态方程的实验研究对靶面光强分布的均匀性及稳定性提出了极高的要求,靶面光强的上述两大特性在很大程度上决定了实验结果的精度和可重复性.本文针对传统窄带高相干激光装置在激光加载材料状态方程实验中表现出的靶面光强均匀性和光强分布稳定性两方面可能存在的问题,提出了基于宽带低相干激光,利用消衍射阵列透镜联合诱导非相干技术的束匀滑方案,并重点分析了波前相位畸变对靶面不均匀性及稳定性的影响.模拟结果表明,该方法明显降低了靶面不均匀性,提高了对波前相位畸变的包容度,获得了均匀、稳定的光强分布.统计分析显示,焦斑强度分布极差和不均匀性与波前相位畸变均方根梯度相关性较强.因此,可以根据统计结果以及实验对焦斑强度分布的要求,给出波前相位畸变的容差范围,对状态方程实验中激光驱动器参数的设计与优化具有指导意义.     

凸透镜焦距测量方法的探索简

凸透镜焦距的测量方法和不确定度评价已经有很多研究,本文着重研究测量方法,提出了应用实物成虚像、虚物成实像方法来测量凸透镜的焦距,并与实物成实像方法进行比较和分析。本文的实验研究拓展了透镜焦距测量的方法,同时更加深入研究了透镜成像的规律,开拓了实验思路。     

激光靶心冲击波观测镜折反式光学系统设计

设计了一种激光靶心冲击波观测镜的光学系统.用反射式光学系统代替折射式光学系统,解决了普通玻璃在200 nm端透过率较低的问题.反射镜不引入色差,有利于系统在200~800 nm谱段消色差.为消系统轴外像差,反射系统选型为对称式.反射镜全部采用球面镜,为消反射镜以及平板玻璃窗带入的球差,引入校正镜(材料JGS1),在满足要求的条件下,控制折射镜的厚度,使系统色差满足瑞利判据的色差允差,得到了良好的成像质量.     

高倍聚光模组系统研究与设计

聚光系统的聚光效率和能量均匀性直接影响单位模组的发电效率。本文研究设计出高倍聚光模组系统,该系统主要包括菲涅耳透镜和球冠平顶微棱镜。采用中心波长修正法进行菲涅耳透镜的设计,并通过Zemax仿真模拟设计出球冠平顶微棱镜。最后通过Zemax模拟,决定选取两侧面夹角α的角度为117°,平顶到球面的间隔g为0.2 mm,球冠平顶微棱镜的曲率半径R为10 mm。聚光系统整体的聚光效率达99.8%,能量均匀度为0.812,并进行实验验证,得出实际聚光效率为83.1%。     

大孔径宽光谱变焦镜头设计北大核心CSCD

在高压电线运输电力过程中容易发生电晕放电现象,存在安全隐患,因此,进行电晕放电的检测十分必要。利用日盲紫外镜头进行电晕检测是检测手段之一。基于Zemax多重组态功能设计了一款大孔径宽光谱变焦镜头,目的是配合变焦范围为90 mm~165 mm变焦距紫外镜头应用,可在电晕放电信号检测时,全天候、快速准确找出损坏线路的位置。该镜头采用4组元、近对称结构型式,F数为1.4,可变焦范围在30 mm~55 mm,工作光谱波段为400 nm~850 nm,空间频率100 lp/mm处全视场MTF≥0.4,最大畸变≤±3%,均采用标准球面设计,系统总长为110 mm,适用于0.847 cm(1/3英寸)CCD,能较好地矫正各类像差,满足各零件基本加工工艺要求。     

不同因素对可调节人工晶体屈光调节力的影响

首先以Hwey-Lan Liou眼模型为基础，根据等效性原则，保持该眼模型中自然晶状体屈光度不变，对无穷远点成像。然后利用ZEMAX实现光线追迹的方法，将自然晶状体替换为可调节人工晶状体（accommodative intraocular lens，AIOL），结合对人眼成像质量影响的分析，研究了AIOL在眼内的移动度、材料、中心厚度、结构、光学面非球面性等因素对其屈光调节力的影响。结果表明:AIOL移动度对其调节力贡献最大,材料、中心厚度、结构对调节力基本无影响；具有非球面光学面的AIOL调节力相对较大。     

Software lens compensation applied to athermalization of infrared imaging systems

A different approach, aiming to achieve the constant blur status of point-spread function (PSF) at a certain defocused plane, is described. The correlation between the two PSF is used to control the PSF blur similarity, and simultaneously the Strehl ratio is also used to control the PSF blur minimization. By designing the PSF so that it is significantly insensitive to defocus or related defocus quantity, for example, due to temperature change, all the constantly blurred images can be accurately de-blurred by a simple inverse restoration filter for an adequate range of defocus. We refer to that as “software lens compensation” and apply a design method to solve the athermalization of middle wavelength infrared (MWIR) imaging systems. The resultant PSF is almost invariant in the temperature range from −10 to 50°C at the same focal plane. Consequently, the constant blur spot can be removed by a simple digital signal processing. Thus, clear and sharp de-blurred images at different temperatures are obtained.     

Enhanced multi‐objective optimization of a dimpled channel through evolutionary algorithms and multiple surrogate methods

Using a multi‐objective evolutionary algorithm (MOEA) and enhanced surrogate approximations, the present study demonstrates the numerical analysis and optimization of staggered‐dimple channels. Two surrogates, the response surface approximation (RSA) model and the Kriging (KRG) model, are applied in light of the surrogate fidelity of the approximate analysis. An enhanced Pareto‐optimal front is obtained by performing local resampling of the Pareto‐optimal front, which provides relatively more accurate Pareto‐optimal solutions in the design space for each surrogate model. Three dimensionless design variables are selected, which are related to geometric parameters, namely, the channel height, dimple print diameter, dimple spacing, and dimple depth. Two objective functions are selected that are related to the heat transfer and pressure loss, respectively. The objective‐function values are numerically evaluated through Reynolds‐averaged Navier–Stokes analysis at the design points that are selected through the Latin hypercube sampling method. Using these numerical simulations two surrogates, viz, the RSA and Kriging models, are constructed for each objective function and a hybrid MOEA is applied to obtain the Pareto‐optimal front. For the particular implementation of surrogate models, it is observed that Pareto‐optimal predictions of the RSA model are better than those of the KRG model, whereas the KRG model predicts equally well at the off‐Pareto‐region (region away from the Pareto‐optimal solutions), which is not the case with the RSA model. The local resampling of the Pareto‐optimal front increases the fidelity of the approximate solutions near the Pareto‐optimal region. The ratios of the channel height to the dimple print diameter and of the dimple print diameter to the dimple pitch are found to be more sensitive along the Pareto‐optimal front than the ratio of the dimple depth to the print diameter. The decrease of the ratio of the channel height to the dimple diameter and the increase of the ratio of the dimple print diameter to the pitch lead to greater heat transfer at the expense of the pressure loss, whereas the ratio of the dimple depth to the print diameter is rather insensitive to Pareto‐optimal solutions. Pareto‐optimal solutions at higher values of the Nusselt number are associated with higher values of the pressure loss due to the increased recirculation, mixing of fluid and vorticity generation. Copyright © 2010 John Wiley & Sons, Ltd.     

决策者具有(严格)凸性偏好结构下的一类交互式多目标决策方法

为了更好地解决决策者具有(严格)凸性偏好结构下的多目标决策问题,一般目标空间为有界凸域的情形常常可以转化为目标空间为有界闭凸区域的情形,首先分析了切割平面及该平面上偏好最优点与被切割平面分割成的为有界闭凸区域的目标空间或目标空间的子集的两个部分之间的关系;然后分析并指出了对于包含全局偏好最优目标方案点的为有界闭凸域的目标空间及其子集(准最优目标集),在确定了切割平面上的偏好最优点后,通过适当地选取供决策者与切割平面的偏好最优点进行比较判断的目标方案点,经过一次比较就可以确定一个新的范围更小的包含全局偏好最优目标方案点的目标空间的有界闭凸子区域(准最优目标集).为获取切割平面上的偏好最优点,提出了改进的坐标轮换法.在这些结论和方法的基础上,提出了决策者具有(严格)凸性偏好结构下的一类交互式多目标决策方法,要求决策者提供较易的偏好性息,决策效能较好.     

Effect of the defect on the focusing in a two-dimensional photonic-crystal-based flat lens

We have investigated in detail the influence of defect on the focusing of electromagnetic waves in a two-dimensional photonic-crystal flat lens by using the finite-difference time-domain method. The result shows that many focusings can be observed at the symmetrical positions when a defect is introduced into the lens. Furthermore, the wave-guides in the lens can confine the transmission wave effectively and improve the quality of the focusing.