塑料闪烁体的辐照特性

利用⁶⁰Co放射源分别对3种塑料闪烁体(BC-408, EJ-200, BC-404)进行辐照损伤研究, 比较辐照前后的透射谱、发射谱及光产额的变化, 发现3种闪烁体在低剂量具有较好的抗辐照性能; 当照射剂量超过1.44×10⁴Gy时,透射谱明显变坏, 光输出减少很严重, 但发射谱却保持不变.     

两种蓝色有机电致发光材料

重点研究以两种蓝色OEL材料蒽类衍生物JBEM和联苯乙烯衍生物DPVBi分别作基质，以perylene作掺杂剂的器件的电致发光性能，特别研究了它稳定性，在这度和效率方面，两种器件并没有很大差别，然而在稳定性方面却有很大差别，蒽类衍生物JBEM的器件在100cd/m^2初始亮度下，半亮度寿命可达1035h，而DPVBi的器件在同样条件下，半亮度寿命为255h。通过分析两种器件的能级图，认为稳定性的差别可能源于两种蓝光材料本身的热稳定性不同，JBEM优于DPVBi，是一种很有前途的蓝色发光材料。     

The effect of ITO films thickness on the properties of flexible organic light emitting diode

Indium tin oxide (ITO) thin films were deposited on cyclic olefin copolymer substrate at room temperature by an inverse target sputtering system. The crystal structure and the surface morphology of the deposited ITO films were examined by X-ray diffraction and atomic force microscopy, separately. The electrical properties of the conductive films were explored by four-point probing. Visible spectrometer was used to measure the optical properties of ITO-coated films. The performance of the flexible organic light emitting diode device with different thickness anode was investigated in this study.     

双轴晶体Nd^3＋：KGd（WO4）2的非偏振吸收光谱研究

报道了用三个方向相互垂直的非偏振吸收光谱测量计算Ｊｕｄｄ－Ｏｆｅｌｔ参数从而算出双轴晶体Ｎｄ３＋ＫＧｄ（ＷＯ４）２的荧光寿命、荧光分支比和发射截面的方法。得到的荧光寿命为１１９μｓ，平均发射截面为２．３×１０－１９ｃｍ２。     

闪烁体荧光传输特性对ETOF探测器性能的影响

为了对BESⅢ端盖飞行时间探测器(ETOF)的测试结果给出合理的解释, 采用Monte Carlo模拟软件包Geant4, 对该探测器测量高能带电粒子的性能进行模拟研究. 详细探讨了当粒子击中ETOF模块不同位置时, 其闪烁体荧光传输特性与探测器模块输出信号之间的关联, 以及PMT输出信号甄别阈值的选取对闪烁探测器本征时间分辨的影响, 并寻找可能的改善时间分辨的方法. 为进一步提高ETOF的性能提供参考.     

Properties of polystyrene-poly(methylmethacrylate) random and diblock copolymers in dilute and semidilute solutions

Solution properties for random and diblock copolymers of polystyrene (PS) and poly(methyl methacrylate) (PMMA) have been measured by dynamic and total intensity light scattering in solvents of differing quality. The results are compared with the corresponding properties for PS and PMMA homopolymers of similar molecular weight, in order to determine if interactions between unlike monomers are significant. The hydrodynamic radius (R_h) and diffusion second virial coefficient (k_d) for the random copolymer are found to be larger than the corresponding values for the homopolymers in a solvent which is near-theta for the two homopolymers, whereas no such effect is observed for the block copolymer. This suggests that most intrachain interactions occur a relatively short distance along the chain backbone. In a mutual good solvent R_h and k_d of the random copolymer are comparable to the average of the values for the homopolymers, indicating that in a good solvent monomer/solvent interactions dominate over monomer/monomer interactions. For an isolated diblock copolymer in a mutual good solvent, there is no evidence that interactions between unlike monomers lead to additional expansion of the entire molecule, as measured by R_h, nor expansion of the individual blocks as probed by light scattering with one block optically masked. However, at low but finite concentration there is evidence (the coefficients of the binary interaction terms in the viscosity and the mutual diffusion coefficient, and the second and third virial coefficients) that a weak ordering effect may exist in block copolymer solutions, far from the conditions where microphase separation occurs. Finally, measurements of ternary polymer-polymer-solvent solutions show no dependence on monomer composition or monomer distribution for the tracer diffusion of probe PS-PMMA copolymers in a PMMA/toluene matrix. This indicate that the frictional interaction is largely unaffected by interactions between unlike monomers. However, there is evidence that the thermodynamic interaction is more unfavorable between a random copolymer and the homopolymer matrix than between a diblock and the matrix. © 1994 John Wiley & Sons, Inc.     

动态光散射实验

动态光散射技术是测量纳米及亚微米颗粒粒径的有效方法．本文介绍了动态光散射实验的原理、实验装置及方法，并测量了粒径为85nm的聚苯乙烯水溶液的粒径，分析了实验产生误差的原因．     

改进型迈克耳孙干涉仪

采用分光梭镜代替迈克耳孙干涉仪中的分束镜和补偿板，不仅消除了杂散光斑，且简化了仪器的结构．     

Implementation and experimental study on fast object modeling based on multiple structured stripes

In this paper, a practical structured light-based system for fast object modeling and reconstruction is reported. The system consists of an off-the-shelf digital projector, a video camera and a turntable. The system calibration is implemented accurately and automatically by taking a single image of an illuminated calibration template. The multiple color light stripes emitted by the projector adopt only three colors and the color can be modified easily according to the surface texture of the object. This makes the system widely applicable in many situations, and the assumption about color neutrality, which is a limitation to other similar systems, can be largely relaxed. The registration and merging algorithm is greatly simplified by employing a turntable. The validity and high accuracy of the method are demonstrated by extensive real experiments.