Carbon Dynamics on the Molybdenum Carbide Surface during Catalytic Propane Dehydrogenation

The effect of the gas‐phase chemical potential on surface chemistry and reactivity of molybdenum carbide has been investigated in catalytic reactions of propane in oxidizing and reducing reactant mixtures by adding H₂, O₂, H₂O, and CO₂ to a C₃H₈/N₂ feed. The balance between surface oxidation state, phase stability, carbon deposition, and the complex reaction network involving dehydrogenation reactions, hydrogenolysis, metathesis, water‐gas shift reaction, hydrogenation, and steam reforming is discussed. Raman spectroscopy and a surface‐sensitive study by means of in situ X‐ray photoelectron spectroscopy evidence that the dynamic formation of surface carbon species under a reducing atmosphere strongly shifts the product spectrum to the C₃‐alkene at the expense of hydrogenolysis products. A similar response of selectivity, which is accompanied by a boost of activity, is observed by tuning the oxidation state of Mo in the presence of mild oxidants, such as H₂O and CO₂, in the feed as well as by V doping. The results obtained allow us to draw a picture of the active catalyst surface and to propose a structure–activity correlation as a map for catalyst optimization.     

Photoswitchable Hydrogel Surface Topographies by Polymerisation‐Induced Diffusion

Herein, we describe the preparation of patterned photoresponsive hydrogels by using a facile method. This polymer‐network hydrogel coating consists of N‐isopropylacrylamide (NIPAAM), cross‐linking agent tripropylene glycol diacrylate (TPGDA), and a new photochromic spiropyran monoacrylate. In a pre‐study, a linear NIPAAM copolymer (without TPGDA) that contained the spiropyran dye was synthesised, which showed relatively fast photoswitching behaviour. Subsequently, the photopolymerisation of a similar monomer mixture that included TPGDA afforded freestanding hydrogel polymer networks. The light‐induced isomerisation of protonated merocyanine into neutral spiropyran under slightly acidic conditions resulted in macroscopic changes in the hydrophilicity of the entire polymer film, that is, shrinkage of the hydrogel. The degree of shrinkage could be controlled by changing the chemical composition of the acrylate mixture. After these pre‐studies, a hydrogel film with spatially modulated cross‐link density was fabricated through polymerisation‐induced diffusion, by using a patterned photomask. The resulting smooth patterned hydrogel coating swelled in slightly acidic media and the swelling was higher in the regions with lower cross‐linking densities, thus yielding a corrugated surface. Upon exposure to visible light, the surface topography flattened again, thus showing that a hydrogel coating could be created, the topography of which could be controlled by light irradiation.     

Exploiting Aggregation To Achieve Phase Separation in Macrocyclization

The aggregation properties of poly(ethylene glycol) (PEG) can be exploited in organic synthesis to control dilution effects. Through the use of solvent mixtures containing PEG₄₀₀/MeOH, macrocyclization by Glaser–Hay coupling can be conducted at high concentrations. The origin of the selectivity has been studied by using surface tension measurements, UV spectroscopy, and chemical tagging and demonstrates the dependence of the yield and selectivity on the aggregation of PEG₄₀₀ and its ability to preferentially solubilize organic substrates, resulting in a phase separation from the catalyst system.     

Plasmonic Scissors for Molecular Design

Heterogeneous catalysts play an important role in surface catalytic reactions, but selective bond breaking and control of reaction products in catalytic processes remain significant challenges. High‐vacuum tip‐enhanced Raman spectroscopy (HV‐TERS) is one of the best candidates to realize surface catalytic reactions. Herein, HV‐TERS was employed in a new method to control dissociation by using hot electrons, generated from plasmon decay, as plasmonic scissors. In this method, the N?N bond in 4,4′‐dimercaptoazobenzene was selectively dissociated by plasmonic scissors, and the reaction products formed from the radical fragment (SC₆H₅N) were controlled by varying the pH value. Under acidic conditions, p‐aminothiophenol was produced from the radical fragment by attachment of hydrogen ions, whereas under alkaline conditions, 4‐nitrobenzenethiol was obtained by attachment of oxygen ions to the substrate.     

Expanded Organic Building Units for the Construction of Highly Porous Metal–Organic Frameworks

Two new organic building units that contain dicarboxylate sites for their self‐assembly with paddlewheel [Cu₂(CO₂)₄] units have been successfully developed to construct two isoreticular porous metal–organic frameworks (MOFs), ZJU‐35 and ZJU‐36, which have the same tbo topologies (Reticular Chemistry Structure Resource (RCSR) symbol) as HKUST‐1. Because the organic linkers in ZJU‐35 and ZJU‐36 are systematically enlarged, the pores in these two new porous MOFs vary from 10.8 Å in HKUST‐1 to 14.4 Å in ZJU‐35 and 16.5 Å in ZJU‐36, thus leading to their higher porosities with Brunauer–Emmett–Teller (BET) surface areas of 2899 and 4014 m² g^?1 for ZJU‐35 and ZJU‐36, respectively. High‐pressure gas‐sorption isotherms indicate that both ZJU‐35 and ZJU‐36 can take up large amounts of CH₄ and CO₂, and are among the few porous MOFs with the highest volumetric storage of CH₄ under 60 bar and CO₂ under 30 bar at room temperature. Their potential for high‐pressure swing adsorption (PSA) hydrogen purification was also preliminarily examined and compared with several reported MOFs, thus indicating the potential of ZJU‐35 and ZJU‐36 for this important application. Studies show that most of the highly porous MOFs that can volumetrically take up the greatest amount of CH₄ under 60 bar and CO₂ under 30 bar at room temperature are those self‐assembled from organic tetra‐ and hexacarboxylates that contain m‐benzenedicarboxylate units with the [Cu₂(CO₂)₄] units, because this series of MOFs can have balanced porosities, suitable pores, and framework densities to optimize their volumetric gas storage. The realization of the two new organic building units for their construction of highly porous MOFs through their self‐assembly with [Cu₂(CO₂)₄] units has provided great promise for the exploration of a large number of new tetra‐ and hexacarboxylate organic linkers based on these new organic building units in which different aromatic backbones can be readily incorporated into the frameworks to tune their porosities, pore structures, and framework densities, thus targeting some even better performing MOFs for very high gas storage and efficient gas separation under high pressure and at room temperature in the near future.     

富锂正极材料Li[Li0.2Mn0.4Fe0.4]O2的表面包覆改性

用共沉淀法合成了富锂正极材料Li[Li0.2Mn0.4Fe0.4]O2,并对其表面进行Al2O3包覆。采用XRD、SEM和电化学测试等方法对样品进行表征。结果表明,与Li[Li0.2Mn0.4Fe0.4]O2相比,包覆改性后的Li[Li0.2Mn0.4Fe0.4]O2具有较好的电化学性能,其初始放电容量未明显降低,而循环寿命大大提高,4.0%Al2O3包覆处理的富锂正极材料经50次充放电循环后,容量衰减量在9%左右。     

十二烷基硫酸钠水溶液的动态表面吸附性质

利用MPTC型气泡压力张仪研究了十二烷基硫酸钠(SDS)溶液在不同NaCl 浓度下的动态表面吸附性质, 分析了离子型表面活性剂在表面吸附层和胶束中形成双电层结构产生表面电荷对动态表面扩散过程和胶束性质的影响. 结果表明, SDS在表面吸附过程中, 表面电荷的存在会产生5.5 kJ·mol^-1的吸附势垒(E_a), 显著降低十二烷基硫酸根离子(DS^-)的有效扩散系数(D_eff). 十二烷基硫酸根离子的有效扩散系数与自扩散系数(D)的比值(D_eff/D)仅为0.013, 这表明SDS与非离子型表面活性剂不同, 在吸附初期为混合动力控制吸附机制. 加入NaCl可以降低吸附势垒. 当加入不小于80 mmol·L^-1 NaCl后, E_a小于0.3 kJ·mol^-1, D_eff/D在0.8-1.2之间, 表现出与非离子型表面活性剂相同的扩散控制吸附机制. 同时, 通过分析SDS胶束溶液的动态表面张力获得了表征胶束解体速度的常数(k₂). 发现随着NaCl 浓度的增大, k₂减小, 表明SDS胶束表面电荷的存在会增加十二烷基硫酸根离子间的排斥力, 促进胶束解体.     

Pt 含量对Co@Pt/C核壳结构催化剂性能的影响

采用两步还原法制得Co@Pt/C核壳结构催化剂, 其中Co与Pt 的总质量分数为20%. 通过改变金属前驱体的用量, 制备了不同Co:Pt 原子比的Co@Pt/C 催化剂, 以20% (w) Co@Pt(1:1)/C 与20% (w) Co@Pt(1:3)/C 表示. 采用透射电镜(TEM)、光电子射线能谱分析(XPS)、循环伏安(CV)、线性扫描伏安(LSV)等方法考察了其结构与性能, 并与实验室早先制备的40% (w) Co@Pt/C 催化剂进行了比较. 自制20% Co@Pt(1:1)/C 与20% Co@Pt(1:3)/C 催化剂的金属颗粒直径约为2.2-2.3 nm, 在碳载体上分散均匀, 粒径分布范围较窄, 电化学活性比表面积(ECSA)分别为56 和60 m²·g^-1, 均超过商用催化剂20% Pt/C(E-tek) (ECSA=54 m²·g^-1). 20%Co@Pt(1:1)/C 与20% Co@Pt(1:3)/C 的半波电位相较于40% Co@Pt(1:1)/C 和40% Co@Pt(1:3)/C 均向正向移动, 表现出更好的氧还原(ORR)催化活性, 并有望降低催化剂的成本, 在质子交换膜燃料电池领域表现出良好的应用前景.     

甲硫醇在Cu(111)表面的解离吸附: 密度泛函理论研究

采用基于密度泛函理论的第一性原理方法和平板模型研究了CH₃SH分子在Cu(111)表面的吸附反应.系统地计算了S原子在不同位置以不同方式吸附的一系列构型, 第一次得到未解离的CH₃SH分子在Cu(111)表面顶位上的稳定吸附构型,该构型吸附属于弱的化学吸附, 吸附能为0.39 eV. 计算同时发现在热力学上解离结构比未解离结构更加稳定. 解离的CH₃S吸附在桥位和中空位之间, 吸附能为0.75-0.77 eV. 计算分析了未解离吸附到解离吸附的两条反应路径, 最小能量路径的能垒为0.57 eV. 计算结果还表明S―H键断裂后的H原子并不是以H₂分子的形式从表面解吸附而是以与表面成键的形式存在. 通过比较S原子在独立的CH₃SH分子和吸附状态下的局域态密度, 发现S―H键断裂后S原子和表面的键合强于未断裂时S原子和表面的键合.     

NO2在Ag/Pt(110)双金属表面上的吸附和分解

利用俄歇电子能谱(AES)和程序升温脱附谱(TDS)研究了NO₂在Ag/Pt(110)双金属表面的吸附和分解.室温下NO₂ 在Ag/Pt(110)双金属表面发生解离吸附, 生成NO(ads)和O(ads)表面吸附物种. 在升温过程中NO(ads)物种发生脱附或者进一步分解. 500 K时NO₂在Ag/Pt(110)双金属表面发生解离吸附生成O(ads)表面吸附物种. Pt 向Ag传递电子, 从而削弱Pt－O键的强度, 降低O(ads)从Pt 表面的并合脱附温度. 发现能够形成具有稳定组成的Ag/Pt(110)合金结构, 其表现出与Pt(110)-(1×2)相似的解离吸附NO₂能力, 但与O(ads)的结合明显弱于Pt(110)-(1×2). 该AgPt(110)合金结构是可能的低温催化直接分解氮氧化物活性结构.