搅拌萃取–分光光度法检测水环境中阴离子表面活性剂

建立搅拌萃取–分光光度法快速检测水环境中阴离子表面活性剂的含量。用三氯甲烷以800~1 200 r/min搅拌萃取水样与亚甲蓝溶液合成的活性物质,搅拌时间为2 min,静置分层后经脱脂棉过滤,待测。阴离子表面活性剂质量浓度在0.050~0.500 mg/L范围内与吸光度线性良好,相关系数大于0.999 0,方法检出限为0.010 mg/L。选择饮用水源水、农村地下水、湖泊水、城市河道水作为研究对象,平行检测结果的相对标准偏差(RSD)为1.9%~6.5%(n=6),加标回收率为91.3%~110%;对标准物质检测结果的相对误差为–2.3%~3.5%,满足实验室分析质量控制要求和现行地表水、地下水质量标准的评价要求。该方法与国标检测方法相比,在准确度、精密度、灵敏度、分析效率及试剂用量方面均有明显优势,具有推广应用价值。     

Investigation of the continuous flow of the sample solution on the performance of electromembrane extraction: Comparison with conventional procedure

In this study, electromembrane extraction from a flowing sample solution, termed as continuous‐flow electromembrane extraction, was developed and compared with conventional procedures for the determination of four basic drugs in real samples. Experimental parameters affecting the extraction efficiency were further studied and optimized. Under optimum conditions, linearity of continuous‐flow procedure was within 8.0–500 ng/mL, while it was wider for conventional procedures (2.0–500 ng/mL). Moreover, repeatability (percentage relative standard deviation) was found to range between 5.6 and 10.4% (n  = 3) for the continuous‐flow procedure, with a better repeatability than that of conventional procedures (2.3–5.5% (n  = 3)). Also, for the continuous‐flow procedure, the estimated detection limit (signal‐to‐noise ratio = 3) was less than 2.4 ng/mL and extraction recoveries were within 8–10%, while the corresponding figures for conventional procedures were less than 0.6 ng/mL and 42–60%, respectively. Thus, the results showed that both continuous flow and conventional procedures were applicable for the extraction of model compounds. However, the conventional procedure was more convenient to use, and thus it was applied to determine sample drugs in real urine and wastewater samples.     

SiCp/Y112铝基复合材料制备工艺及性能

3种不同铸造工艺条件下铝基复合材料的微观组织,并对其硬度进行了测定.研究表明:与全液态铸造法和半固态铸造法相比,搅熔铸造制备的SiCp/Y112铝基复合材料,其增强相SiC颗粒分布均匀,气孔率较少.是一种较理想的金属基复合材料制备工艺.未增强的Y112基体铝合金的维氏硬度高于其半固态坯料的维氏硬度;而SiCp/Y112铝基复合材料的维氏硬度明显高于基体的维氏硬度,并随着SiC颗粒的体积分数的增加其复合材料的维氏硬度不断提高.     

Adiabatic Calorimetry Using Directly Agitated Test Cells

This paper explains why directly agitated test cells are sometimes required in order to obtain good adiabatic calorimetry data that can be used with confidence to predict large scale plant behaviour. Experiments for methyl methacrylate polymerisation are reported. Simple procedures are presented for calculating genuine thermo-kinetic parameters from data which includes energy dissipation from the stirrer drive system.This revised version was published online in November 2005 with corrections to the Cover Date.     

Application of rotating magnetic fields in Czochralski crystal growth

The physical principles of electromagnetic stirring with a rotating magnetic field are explained and a mathematical model to calculate the electromagnetic volume force, the fluid flow and the transport of heat and solutes is outlined. For the electromagnetic volume force and for the order of magnitude of the flow velocities approximative analytical expressions are given. A high flexibility in configuring the volume force in order to achieve a desired flow distribution is obtained by multi-frequency stirring that is by superposition of two or several magnetic fields with different frequencies and/or sense of rotation. Results of experimental investigation and mathematical simulation of multi-frequency stirring are given. Numerical simulation of the fluid flow, the temperature and the oxygen distribution in a Czochralski process crucible was performed including the effect of single mode and multi-frequency stirring. The results indicate that electromagnetic stirring should offer large potentials for the optimization of the flow configuration in a Czochralski process crucible. Finally examples from literature of practical application of rotating magnetic fields in crystal growth are presented.     

Effectiveness of stirring measures in an axisymmetric rotating annulus flow

Lagrangian stirring in a thermally driven rotating annulus is investigated numerically using a Navier-Stokes model and a second order Runge-Kutta integration routine. The stirring properties are investigated using finite scale Lyapunov exponents, Lagrangian coherent structures and a leaking method. The ability of these measures to identify transport barriers, regions of well and poorly stirred flow, and stable and unstable manifolds is investigated, as well as the stirring properties of the annulus flow. It is found that finite scale Lyapunov exponents characterise the stirring properties of flows occurring in the rotating annulus more efficiently than the leaking method or Lagrangian coherent structures. The strength of the stirring varies monotonically with thermal forcing amplitude, but non-monotonically with forcing frequency. The flows investigated are axisymmetric (i.e. two dimensional) and time dependent.     

频率搅拌混响室原理及应用

从理论上分析了混响室采用频率搅拌的可行性,仿真计算和试验测量了频率搅拌混响室内部电场的均匀性和统计特性,探索了在屏蔽效能测试中的应用。研究结果表明：频率搅拌方法能够得到空间统计均匀的电场分布,电场直角分量的模值服从瑞利分布,并且频率越高电场的均匀性和统计特性越好。在频率搅拌混响室内部测试得到开缝小尺寸屏蔽体在1~10 GHz频段的屏蔽效能约为15 dB,与机械搅拌混响室测试结果基本一致。关键词： Abstract: Key words:     

Ultrasonic-assisted electrodeposition of Ni/diamond composite coatings and its structure and electrochemical properties

Ni/diamond composite coatings have been synthesized by ultrasonic-assisted electrodeposition in a Ni electroplating bath containing diamond nanoparticles. The influences of current density and ultrasonic agitation on the coating composition, morphology, topography, phase structure, and electrochemical characteristics of the electrodeposits were evaluated. Ultrasonic agitation was provided using an external ultrasonic bath at a frequency of 40 kHz and acoustic power of 300 W. Coating samples were also prepared under magnetic stirring for comparison with the ultrasonic-assisted deposits. This work reveals that the diamonds have been incorporated and evenly distributed in the composites. The coatings exhibit dense, granular like morphology with pyramid-like grains. As current density increases, the diamond amount of ultrasonic-assisted electrodeposits first increased to maximum of 11.4 wt% at 3 A dm⁻² and then decreases to 9.9 wt% at 5 A dm⁻², and the RTC of the preferred orientation (2 0 0) plane increases from 76.3% up to 93.4%. The crystallite size was 60–80 nm and the R_a of the magnetic and ultrasonic agitations were 116 nm, 110 nm, respectively. The maximum R_p of 39.9, 50.3 kΩ cm² was obtained at 4 A dm⁻² when respectively immersed 30 min and 7 days, illustrating the best corrosion resistance of the coatings of 4 A dm⁻². The effects of mechanical and ultrasonic agitations on the mechanism of the co-electrodeposition process were both proposed. The incorporation of diamond particles enhances the hardness and wear-resisting property of the electrodeposits. The ultrasonic-assisted electrodeposited Ni/diamond coating has better corrosion resistance than that prepared under mechanical stirring conditions.     

On the Circulation Structure and Formation Mechanism of the Cold Water Mass of the Yellow Sea (Ⅰ)——Zero-order Solution and Circulation Structure

A series of studies have been made on the circulation structure and the responsible mechanisms related to the Cold Water Mass of the Yellow Sea. From the present model governing the nonlinear thermally driven circulation in shallow seas, some complete analytical solutions of temperature and velocity components have been obtained in this paper by solving the coupled equations of motion and heat conduction. The results demonstrate that the wind-induced stirring and the tidal mixing are all responsible for the termal structure formation of Cold Water Mass. The computed vertical convection (u-w) develops only within a thin layer (called "a current shell" here) in the vicinity of thermocline while the deeper layer remains almost motionless. This current structure represents well the maintenance mechanisms of thermocline or the Cold Watermass during the summer.     

On ion transport regulation with field-effect nonlinear electroosmosis control in microfluidics embedding an ion-selective medium

We study herein numerically the use of induced-charge electrokinetic phenomena to enable a flexible control of ion transport of dilute electrolyte in a straight ion concentration polarization system. The effect of three convection modes of induced-charge electrokinetic phenomena, including induced-charge electroosmosis, flow-field effect transistor, and alternating-current electroosmosis (ACEO), on convective arrestment of diffusive wave-front propagation is investigated by developing a cross-scale and fully coupled transient numerical simulation model, wherein multiple frequency electrochemical polarization and nonlinear diffuse charge dynamics in spatiotemporally varying solution conductivity are taken into account. We demonstrate by detailed comparative simulation studies that ACEO vortex flow field above a metal strip array arranged along the anodic chamber's bottom surface serves as the most efficient way for adjusting the salt density distribution at micrometer and even millimeter dimension, due to its high flexibility in controlling the stirring flow state with the introduction of two extra electrical parameters. The specific operating status is determined by whether the electrode array is floating in potential (induced-charge electroosmosis) or biased to ground (flow-field effect transistor) or forced to oscillate at another Fourier mode (ACEO). These results prove useful for on-chip electric current control with electroconvective stirring.