Sample preparation procedure for the determination of sulphur and trace metals in oil products by the ICP with a minitorch using emulsions

A quick sample preparation method was used for the determination of sulphur and trace metals in oil and oily products by the ICP with a minitorch. Stable aqueous emulsions of oils and oil products were made by using two kinds of emulsifiers (one with low sulphur content, the other sulfonated). Aqueous standard solutions can be used for the preparation of calibration solutions. The contents of S, Al, Cr, Cu, Fe, Mg, Ni and Pb in aqueous emulsions were determined and the results were in good agreement with the composition of oil standard solutions used for control analysis procedure.     

Effect of the pore surface modification of an inorganic substrate on the plasma‐grafting behavior of pore‐filling‐type organic/inorganic composite membranes

We have investigated the effect of the surface state and surface treatment of the pores of an inorganic substrate on the plasma‐grafting behavior of pore‐filling‐type organic/inorganic composite membranes. Shirasu porous glass (SPG) was used as the inorganic substrate, and methyl acrylate was used as the grafting monomer. The grafting rate increased as the density of silanol on the SPG substrate increased. This result suggests that radicals are generated mainly at the silanol groups on the pore surface by plasma irradiation. The SPG substrates were treated with silane coupling agents used to control the mass of organic material bonded to the pore surface. The thickness of the grafted layer became thinner as the mass of organic material bonded to the pore surface of SPG increased. This decrease in the thickness of the grafted layer could be explained by the decrease in the penetration depth of vacuum ultraviolet rays contained in plasma having a wavelength of less than 160 nm that generated radicals in the pores of the substrate. The thickness of the grafted layer inside the SPG substrates could be controlled through the control of the mass of organic material bonded to the pore surface of the SPG substrate. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 846–856, 2006     

Surface characterization and barrier properties of plasma‐modified polyethersulfone/layered silicate nanocomposites

This study describes the preparation of polyethersulfone (PES)/layered silicate nanocomposites (PLSNs) by mixing PES polymer chain into organically‐modified layered silicate in 1‐methyl‐2‐pyrrolidinone (NMP) solution. Both X‐ray diffraction data and transmission electron microscopy images of PLSNs indicate that the silicate layers were almost exfoliated and randomly distributed into the PES matrix. The mechanical and barrier properties of PLSNs show remarkable enhancement in the storage modulus and water/oxygen permeability when compared with that of neat PES matrix. Surfaces modification of PES and PLSN films with various treated times, system pressures, and radio frequency (RF) powers were performed using a mixture of oxygen (O₂) and nitrogen (N₂) plasmas. The topographical and physical properties of plasma‐modified PES and PLSN surfaces were investigated using scanning probe microscopy (SPM), contact‐angle measurements, and X‐ray photoelectron spectroscopy (XPS). These results indicate that the surface roughness of PLSNs with the same condition of plasma modification is lower than that of neat PES matrix and is probably due to the increase of stiffness with the presence of inorganic layered silicates in PES matrix. The surface properties of the PES and PLSNs are also changed from hydrophobic to hydrophilic. The XPS spectra suggest that the exposure of the PES and PLSNs to the plasmas led to the combination of etching reactions of polymer surface initiated by plasma and the following addition reactions of new oxygen‐ and nitrogen‐containing functional groups onto polymer surfaces to change their surface properties. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3185–3194, 2006     

Nd掺杂的Bi4Ti3O12变温X射线衍射分析

利用变温X射线衍射技术，在预烧过程中分析了Nd掺杂Bi4Ti3O12后生成Bi3.15Nd0.85Ti3O12（BNT）相的形成过程以及微结构的变化．实验观察到以30℃／min的升温速率，BNT相在700℃时开始形成，其衍射峰强度随温度的继续升高而增强，衍射峰半高宽随烧结时间延长而减小．X射线衍射分析结果表明，在900℃恒温条件下，烧结约2h，可形成单一的BNT相．     

Modification of a three-way catalyst washcoat by aging: A study along the longitudinal axis

This work reports the research carried out by studying aliquots extracted at different axial coordinates from Three Way Catalyst (TWC) monoliths aged under real traffic conditions. Our study focused on the catalytic properties and on several chemical and physical effects caused in the Front and Rear monolith washcoat surfaces by vehicle aging after 60,000 km. Regarding the catalytic properties, all the used aliquots showed poorer activity than their corresponding fresh counterparts. The strongest deactivation was detected for NO and hydrocarbon conversion. CO conversion was less affected and the Rear monolith was as deactivated as the Front one. The characterisation techniques (TXRF, N₂ adsorption-desorption isotherms, XRD and H₂-TPR) detected - (i) the deposition of P, Zn and Pb; (ii) the formation of CePO₄ on account of the Ce from the washcoat; (iii) thermal sintering; (iv) inhibition of the reducibility of Ce oxides - as the main effects brought about by vehicle aging conditions. The deactivation observed at the beginning of the Front monolith was the result of a combination of the former effects. When moving downstream to higher axial coordinates, Pb accumulation and the loss of specific area appeared to be the only probable sources of deactivation.     

Multiscale Finite Element Modeling of Arc Dynamics in a DC Plasma Torch

The dynamics of the electric arc inside a direct current non-transferred arc plasma torch are simulated using a three-dimensional, transient, equilibrium model. The fluid and electromagnetic equations are solved numerically in a fully coupled approach by a multiscale finite element method. Simulations of a torch operating with argon and argon–hydrogen under different operating conditions are presented. The model is able to predict the operation of the torch in steady and takeover modes without any further assumption on the reattachment process except for the use of an artificially high electrical conductivity near the electrodes, needed because of the equilibrium assumption. The results obtained indicate that the reattachment process in these operating modes may be driven by the movement of the arc rather than by a breakdown-like process. It is also found that, for a torch operating in these modes and using straight gas injection, the arc will tend to re-attach to the opposite side of its original attachment. This phenomenon seems to be produced by a net angular momentum on the arc due to the imbalance between magnetic and fluid drag forces.     

Studies on the Plasma Shielding of 1.06μm Laser on the Aluminum Target

ＳｔｕｄｉｅｓｏｎｔｈｅＰｌａｓｍａＳｈｉｅｌｄｉｎｇｏｆ１．０６μｍＬａｓｅｒｏｎｔｈｅＡｌｕｍｉｎｕｍＴａｒｇｅｔＬＵＪｉａｎ；ＮＩＸｉａｏｗｕ；ＨＥＡｎｚｈｉ（ＤｅｐａｒｔｍｅｎｔｏｆＡｐｐｌｉｅｄＰｈｙｓｉｃｓ，ＮａｎｊｉｎｇｏｆＳｃｉｅｎｃ...     

HCN laser scattering on the JIPP T-IIU tokamak

A 4-channel HCN laser scattering system has been developed and applied to the JIPP T-IIU tokamak. Main aim of this system is to study microturbulence excited in the plasma, especially in the high power ICRF heating experiment. The observed density fluctuations are in a frequency range of the electron diamagnetic drift wave and have broad frequency spectra. The main part of the wavenumber is found to satisfy the condition of . In the heating experiments, deterioration of the energy confinement time is observed, and the density fluctuation level increases with the increase of the heating power.     

软X射线显微术Si_3N_4薄膜窗口的研制

介绍了在软Ｘ－射线显微术研究领域中有重要应用的Ｓｉ_３Ｎ_４薄膜窗口的实验室制作方法，并形成一套独特制备工艺，Ｓｉ_３Ｎ_４薄膜窗口的研制成功推动了我国软Ｘ射线显微术研究的发展。