晶格振动和热电子对疏松金属材料冲击压缩特性的贡献

 根据固体晶格的谐振子模型、热电子的自由电子气模型以及Grüneisen物态方程，仅通过简洁的代数运算分别导出晶格振动、热电子对疏松金属材料的冲击温度、冲击压强、乃至压缩体积贡献的计算公式。结果表明：晶格振动对冲击压缩体积的贡献分量计算公式与吴-经方程的推导结果在形式上具有很好的一致性，同时改进了热电子对体积贡献分量的计算公式。并论证了两个体积贡献分量表达式的合理性及其物理意义。     

Cu对用于高速相变存储器的Sb2Te薄膜的结构及相变的影响研究

采用原位X射线衍射仪、拉曼光谱仪和X射线反射仪分别研究了Cu-Sb₂Te 薄膜的微结构、成键结构和结晶前后的密度变化. Sb₂Te薄膜的结晶温度随着Cu含量的增加而增大. 在10 at.%和14 at.% Cu的Sb₂Te薄膜中, Cu与 Te 成键, 结晶相由六方相的Cu₇Te₄、菱形相的Sb及六方相的Sb₂Te构成. 10 at.% 和14 at.% Cu 的Sb₂Te薄膜在结晶前后的厚度变化分别约为3.2%和 4.0%, 均小于传统的Ge₂Sb₂Te₅ (GST)薄膜. 制备了基于Cu-Sb₂Te薄膜的相变存储单元, 并测试了其器件性能. Cu-Sb₂Te器件均能在10 ns的电脉冲下实现可逆SET-RESET操作. SET和RESET操作电压随着Cu含量的增加而减小. 疲劳测试结果显示, Cu 含量为10 at.%和14 at.%的PCRAM单元的循环操作次数分别达到1.3×10⁴和1.5×10⁵, RESET和SET态的电阻比值约为100. Cu-Sb₂Te可以作为应用于高速相变存储器(PCRAM)的候选材料.     

非定常瞬态流动过程中的Lagrangian拟序结构与物质输运作用

从Lagrangian角度数值分析了圆柱瞬时起动过程中的非定常瞬态流动现象,如分离泡产生、破裂和涡脱落等及其产生的非定常效应,揭示了所列现象诱导的物质输运和迁移效应,首先采用双时间步长的特征线算子分裂算法数值模拟了圆柱起动过程中的瞬时流场,然后采用数值方法从流场中提取出Lagrangian拟序结构(LCSs),并根据非线性动力学理论研究了流动分离和旋涡演化过程中的物质输运作用,结果表明,圆柱瞬时起动后所产生的非定常阻力与相应瞬态现象中的物质输运有密切的关系:对称分离泡产生及其在流向方向的生长,能够使分离泡内压力升高且分布均匀,从而减小阻力;对称分离泡的失稳增强了分离泡与主流之间的物质输运作用,最终导致涡的脱落,并有利于推迟流动分离和减小分离区域,非定常流动中LCSs所描述的物质输运和迁移作用对流动控制的机理研究具有一定指导意义。     

压电复合材料层合板自适应结构的振动控制

本文针对板壳型自适应结构,研究了压电材料作为作动器的自适应结构的振动控制。利用四节点压电复合材料层合板单元进行自适应结构的有限元动力分析;采用模态控制方法,将结构的各阶模态的阻尼比作为控制目标,并以此计算出各压电片的控制电压,达到控制结构振动的目的。算例给出了数值计算的结果。     

Synthesis and Properties of Novel Luminescent Compounds Containing Triphenylamine and Bipyridine Units

Blue luminescent compounds T1-T4 containing triphenylamine donors,bipyridine acceptors and olefinic linkers were synthesized and characterized by 1H NMR,13C NMR and high resolution mass spectrometry(HR...     

COUPLING EFFECTS OF VOID SHAPE AND VOID SIZE ON THE GROWTH OF AN ELLIPTIC VOID IN A FIBER-REINFORCED HYPER-ELASTIC THIN PLATE

The growth of a prolate or oblate elliptic micro-void in a fiber reinforced anisotropic incompressible hyper-elastic rectangular thin plate subjected to uniaxial extensions is studied within the framework of finite elasticity. Coupling effects of void shape and void size on the growth of the void are paid special attention to. The deformation function of the plate with an isolated elliptic void is given, which is expressed by two parameters to solve the differential equation. The solution is approximately obtained from the minimum potential energy principle. Deformation curves for the void with a wide range of void aspect ratios and the stress distributions on the surface of the void have been obtained by numerical computation. The growth behavior of the void and the characteristics of stress distributions on the surface of the void are captured. The combined effects of void size and void shape on the growth of the void in the thin plate are discussed. The maximum stresses for the void with different sizes and different void aspect ratios are compared.     

SINGLE AND DOUBLE EDGE INTERFACE CRACK SOLUTIONS FOR ARBITRARY FORMS OF MATERIAL COMBINATION

In this paper interfacial edge crack problems are considered by the application of the finite element method. The stress intensity factors are accurately determined from the ratio of crack-tip-stress value between the target given unknown and reference problems. The reference problem is chosen to produce the singular stress fields proportional to those of the given unknown problem. Here the original proportional method is improved through utilizing very refined meshes and post-processing technique of linear extrapolation. The results for a double-edge interface crack in a bonded strip are newly obtained and compared with those of a single-edge interface crack for different forms of combination of material. It is found that the stress intensity factors should be compared in the three different zones of relative crack lengths. Different from the case of a cracked homogeneous strip, the results for the double edge interface cracks are found to possibly be bigger than those for a single edge interface crack under the same relative crack length.     

超高强度钢（35CrNi3Mo）化学成分标准物质研制

采用与超高强度钢,台炼过程相同的工艺制备了35CrNi3Mo化学成分标准物质。对标准物质的制备技术、均匀性检验、稳定性考察进行了分析。研制的35CrNi3Mo化学成分标准物质具有良好的均匀性和稳定性。采用8家实验室进行协作定值,对定值结果的不确定度进行评定,各组分定值结果的相对扩展不确定度小于13％。     

Finite Element Based Micro-mechanical Modeling of Interphase in Filler Reinforced Elastomers

Characteristic properties of elastomers can be tailored by embedding them with filler particles. Along with enhancing the overall properties of the composite, filler particles also induce some inelastic effects. In this paper, a finite element computational model is used to study the effect of microstructure morphology in filled elastomers, on its macroscopic large deformation behavior. A multiphase material model that accounts for the hypothesis of shift in glass transition temperature in the vicinity of the filler particle is developed to simulate the interphase between the fillers and the matrix. It also accounts for the breakdown and re-aggregation of filler networks under cyclic loading. Examples at the microstructural level, demonstrating the dynamics of the interphase using the developed multiphase model have been successfully simulated. The obtained results are in good qualitative agreement with the Mullins effect. Therefore, computational experiments using this methodology enable the prediction of the experimentally observed softening behavior in filled elastomers based on its microstructure evolution.