Determination of various inorganic anions and organic acids in the atmospheric particulate matter using capillary zone electrophoresis with indirect UV detection

Capillary zone electrophoresis with indirect UV detection was developed for the simultaneous analysis of inorganic anions and organic acids using a mixed solution of 2,6-pyridinedicarboxylic acid and cetyltrimethylammonium hydroxide as the background electrolyte (BGE). The parameters which influence the separation, such as indirect UV detection wavelength, BGE conditions, applied voltage and extraction conditions were investigated. Thirteen inorganic anions and organic acids were detected within 20 min. The calibration curves of each analyte were linear with correlation coefficients greater than 0.991. The relative standard deviations (n = 10) of the peak areas ranged from 0.6% to 3.3%. The detection limits for these species ranged from 0.4 to 1.4 mg/L at a signal-to-noise ratio of 3. The recovery rate of each analyte was more than 80% under optimised extraction conditions, except for nitrite. The proposed method was applied towards the analysis of inorganic anions and organic acids in the atmospheric particulate matter using an Andersen sampler. The particle size of the particulate matter was determined, but not the size of the anions.     

滑带土动力学性质试验研究

为了研究地震高烈度区老滑坡的复活变形原因,本文对滑坡滑带土的动力学特性进行了系列研究。本次试验采用扰动土样,制样基本物理指标按滑带土的现场测试指标确定,在不固结不排水条件下,运用MTS810Teststar程控液压伺服土动三轴仪对单个样品逐级放大动应力的分级试验方法进行。侧向压力 (围压 )分别采用 100kPa、20 0kPa、300kPa三级,通过施加轴向振动荷载 (力 )模拟地震作用,振动波形为正弦波,频率为 1Hz,振幅随试样性质确定。研究结果表明,滑带土在动荷载作用下的动力学性质与其静荷载作用下的力学性质有着较大的差异,主要表现在滑带土的动应力与动应变关系的非线性、滞后性及变形积累特点,动弹性模量与动强度的显著降低以及动阻尼比的显著增大特性。这揭示了动力作用下的滑坡复活原因之一,同时为滑坡稳定性评价和动力作用下的变形机制模拟分析提供了基础资料,也为分析滑带土动力本构模型提供了基本内容。     

Two-parameter failure criterion for elastoplastic bodies with mode I cracks

The generalized Dugdale crack model is used to formulate two-parameter failure criteria for the cases of quasibrittle state and developed plastic zones at a mode I crack tip. The failure criteria relate the fracture strength characteristics and the stress mode at the crack tip through the plastic constraint factor. The critical state of bodies with cracks under uni-and biaxial loading is analyzed in the cases of plane stress and plane strain using the Tresca and von Mises yield criteria. A small-scale yield criterion, which is an analytic relation between the critical stress intensity factor and T-stresses, is established __________ Translated from Prikladnaya Mekhanika, Vol. 43, No. 7, pp. 47–57, July 2007.     

基于风洞试验的不同坡度多跨锯齿屋面风压特性研究

多跨锯齿屋面因其具有跨度大、结构轻盈的特点成为典型的风灾易损结构.目前国内规范对锯齿屋盖的风荷载规定较为粗略,简单给定了统一的风压系数参考值,在实际工程应用中具有一定的局限性.本文以某4跨锯齿房屋为研究对象,通过风洞试验测试了15°、21°、26°、30°和40°等5种不同屋面坡度对锯齿屋盖风压特性的影响.试验结果表明...     

毛细管电泳-柱端安培检测法用于抗癌药物2-氨基-6-巯基嘌呤和8-氮杂鸟嘌呤的研究

采用毛细管电泳-安培检测法建立一种简单、快速、有效的同时分析抗癌药物2-氨基-6-巯基嘌呤和8-氮杂鸟嘌呤的新方法.在长50 cm、内径为25μm的未涂层毛细管中,采用20 mmol/L磷酸盐(pH为7.0)缓冲液作为运行液,当分离电压为21 kV时,两组分在12 min内达到基线分离.在上述最佳分离条件下,当电极电位为1.050V、进样时间为10 s时,2-氨基-6-巯基嘌呤和8-氮杂鸟嘌呤的峰电流和浓度之间呈良好的线性关系,其相关系数分别为0.999 20、.999 0,检测限分别为3.0×10-7、2.0×10-7mol/L.7次重复实验2-氨基-6-巯基嘌呤和8-氮杂鸟嘌呤的日间峰电流RSD分别为2.44%3、.46%.利用该法检测了牛血清蛋白中的2-氨基-6-巯基嘌呤和8-氮杂鸟嘌呤,回收率分别为100%-113%,93.0-102%.     

Physical characterization of a new composition of oxidized zirconium-2.5 wt% niobium produced using a two step process for biomedical applications

Zirconium and particularly Zr-2.5 wt%Nb (Zr2.5Nb) alloy are useful for engineering bearing applications because they can be oxidized in air to form a hard surface ceramic. Oxidized zirconium (OxZr) due to its abrasion resistant ceramic surface and biocompatible substrate alloy has been used as a bearing surface in total joint arthroplasty for several years. OxZr is characterized by hard zirconium oxide (oxide) formed on Zr2.5Nb using one step thermal oxidation carried out in air. Because the oxide is only at the surface, the bulk material behaves like a metal, with high toughness. The oxide, furthermore, exhibits high adhesion to the substrate because of an oxygen-rich diffusion hardened zone (DHZ) interposing between the oxide and the substrate.In this study, we demonstrate a two step process that forms a thicker DHZ and thus increased depth of hardening than that can be obtained using a one step oxidation process. The first step is thermal oxidation in air and the second step is a heat treatment in vacuum. The second step drives oxygen from the oxide formed in the first step deeper into the substrate to form a thicker DHZ. During the process only a portion of the oxide is dissolved. This new composition (DHOxZr) has approximately 4-6 μm oxide similar to that of OxZr. The nano-hardness of the oxide is similar but the DHZ is approximately 10 times thicker. The stoichiometry of the oxide is similar and a secondary phase rich in oxygen is present through the entire thickness. Due to the increased depth of hardening, the critical load required for the onset of oxide cracking is approximately 1.6 times more than that of the oxide of OxZr. This new composition has a potential to be used as a bearing surface in applications where greater depth of hardening is required.     

Research on identifying the order of fringe pattern traces using angular scan and zone search method

A method for automatically identifying the order of fringe pattern traces is presented. It uses the simplified Otsu algorithm for obtaining the threshold, the angular scan in the range of 45~ for searching the trace positions, and the zone search technique for identifying different traces. Experimental results show that the proposed method may reliably obtain the order of fringe pattern traces orientating from almost 45° to 90°.     

Chiral Separation of Esmolol and Terazosin by Cyclodextrinmodified Capillary Zone Electrophoresis

IntroductionTheincreasingnecessity0fpharmacologicalresearchforchiraldrugshasrenderedchiralseparationanactiveareaincaPillaryelectroph0resis(CE)today.Variousmodes0fCE,includingcaPillaryzoneelectroph0resis(CZE),micellarelectrokineticchromatography(MEKC),caPillarygelelectrophoresis(CGE)andcapillaryisotachophoresis(CITP),havebeenappliedforthispurp0se',amongwhichCZEisthemostpopularoneforitshighefficiency,lowexpenseandeaseofoperation.Forsuccessfulchiralseparati0ninCZE,theselectortypeisofcr…     

高分辨率X射线显微成像及其进展

介绍了高分辨率X射线显微成像产生背景和发展过程，着重分析了基于光学元件波带片的放大成像的基本原理，并简述了高分辨率三维成像的有关理论。同时给出国内外高分辨率X射线显微成像研究的最新进展，展望了高分辨率X射线显微成像的应用前景。     

Analytical solution to a mode of mixed elastohydrodynamic lubrication with mixed contact regimes: Part I. Without consideration of contact adhering layer in the inlet zone

In 2005, Zhang presented a Grubin-like inlet zone analysis to the isothermal line contact elastohydrodynamic lubrication under relatively heavy loads when the hydrodynamic film thickness in the Hertzian zone approaches zero and the EHL fluid is Newtonian [Zhang, Y.B. A justification of the load-carrying capacity of elastohydrodynamic lubrication film based on the Newtonian fluid model. Industrial Lubrication and Tribology, 2005, Vol. 57, pp. 224–232]. His results showed that in this EHL, when the rolling speed is lower than the characteristic rolling speed (U_ch =) 0.0372W^1.50/G, the Hertzian zone is in physical adsorbed layer boundary lubrication while the inlet zone is in conventional hydrodynamic lubrication. This mode of EHL represents a mode of mixed EHL with mixed contact regimes, where hydrodynamic films with different rheological behaviors occur in different areas of the contact. The present paper presents an analysis to this mode of mixed EHL by using the Grubin type method when the contact adhering layer in the inlet zone is neglected. Pressures, film thicknesses and load partition in the contact are obtained from this analysis. It is also found that the formula for the characteristic rolling speed U_ch = 0.0372W^1.50/G obtained by Zhang [Zhang, Y.B. A justification of the load-carrying capacity of elastohydrodynamic lubrication film based on the Newtonian fluid model. Industrial Lubrication and Tribology, 2005, Vol. 57, pp. 224–232] may be valid for the dimensionless load W > 1.0E−7, while it may be invalid for the dimensionless load W < 1.0E−8. In part II [Zhang, Y.B. Analytical solution to a mode of mixed elastohydrodynamic lubrication with mixed contact regimes: Part II. Considering the contact adhering layer effect in the inlet zone. Journal of Molecular Liquids, 2006, Vol. 117. (doi:10.1016/j.molliq.2006.04.007)] will be presented an analysis to other two modes of mixed EHL with mixed contact regimes for relatively heavy loads, low rolling speeds and Newtonian fluids, where the conventional hydrodynamic lubrication, physical adsorbed layer boundary lubrication and oxidized chemical layer boundary lubrication can simultaneously occur in the inlet zone while the oxidized chemical layer boundary lubrication or the fresh metal-oxidized chemical boundary layer dry contact occur in the Hertzian zone, considering the contact adhering layer effect in the inlet zone.