The structure of CeAlO3 by Rietveld refinement of X-ray powder diffraction data

The room temperature structure of perovskite CeAlO₃ has been reinvestigated by X-ray powder diffraction. The Rietveld refinement has confirmed the tetragonal symmetry; but revealed a super cell, a=5.32489(6) Å and c=7.58976(10) Å, with the space group I4/mcm. In CeAlO₃, the distortion from the ideal cubic perovskite is caused by the cooperative tilting of the AlO₆ octahedra around the primitive cubic [001]_p-axis.     

Crystallographic report: Diiodo[tris(2‐pyridyl)amine]mercury(II), [(C5H4N)3N]HgI2

In mononuclear HgI₂[(C₅H₄N)₃N], mercury is tetrahedrally coordinated by two nitrogen atoms of a tris(2‐pyridyl)amine ligand and two iodides. The coordination moieties are connected by weak intermolecular Hg(II)···I interactions to give a one‐dimensional structure. Copyright © 2003 John Wiley & Sons, Ltd.     

CNx纳米管的制备、结构观察及低场致电子发射性能研究

采用高温热解法，以乙二胺为前驱液，在沉积有铁催化剂的p型硅（111）基底上制备出了定向生长的CNx纳米管.利用扫描电子显微镜、高分辨率透射电子显微镜和拉曼光谱对CNx纳米管进行了形貌观察和表征.CNx纳米管的高度在20?μm左右，直径在50—100nm之间，具有明显的“竹节状”结构，结晶有序度较差.对CNx纳米管薄膜进行低场致发射性能测试：外加电场为1.4V/μm，观察到20?μA /cm2发射电流，外电场升至2.54V/μm时发射电流达到1.280mA/cm2，在较高外电场下，没有发现电流“饱和”.这比 关键词： CNx纳米管 高温热解 “竹节状”结构 场致发射     

Structure and Structural Nonrigidity of Tetrachlorodibenzo-p-Dioxin Radical Cations

Ab initio calculations showed that the tetrachlorodibenzo-para-dioxin radical cations (TCDD RCs) with a planar structure have two steady states with asymmetric dioxin cycles. The activation barriers between these states are up to 2 kcal/mole, so that the RCs may be regarded as being structurally nonrigid within the dioxin cycle. The 2,3,7,8-TCDD RC is more stable than the 1,4,6,9-TCDD RC, the energy difference being 5.2 kcal/mole. The adiabatic ionization potential of 2,3,7,8-TCDD (7.54 eV) is 0.1 eV smaller than the corresponding potential of 1,4,6,9-TCDD. These factors account for the increased hemoproteide affinity and hence increased biological activity of 2,3,7,8-TCDD.     

Synthesis and Crystal Structure of the Hydrogen Polyphosphide Bis(Tetraphenylphosphonium) hydrogenheptaphosphide‐ammonia(1/3) (PPh4)2HP7 · 3NH3

(PPh₄)₂HP₇ · 3NH₃ was prepared by the reaction of K₃P₇ with a proton‐charged ion exchange resin in the presence of (PPh₄)Br in liquid ammonia, and characterized by low temperature X‐ray structure analysis. The thermally very unstable compound contains the hydrogenheptaphosphide anion HPequation/tex2gif-stack-1.gif, the nortricyclane‐like cage of which is slightly distorted by the attachment of the hydrogen atom.     

Conformal Invariance, Accelerating Universe and the Cosmological Constant Problem

We investigate a conformal invariant gravitational model which is taken to hold at early universe. The conformal invariance allows us to make a dynamical distinction between the two unit systems (or conformal frames) usually used in cosmology and elementary particle physics. In this model we argue that when the universe suffers phase transition, the resulting mass scale introduced by particle physics should have a variable contribution to vacuum energy density. This variation is controlled by the conformal factor which is taken as a dynamical field. We then deal with the cosmological consequences of this model. In particular, we shall show that there is an inationary phase at early times. At late times, on the other hand, it provides a mechanism which makes a large effective cosmological constant relax to a sufficiently small value. Moreover, we shall show that the conformal factor acts as a quintessence field that leads the universe to accelerate at late times.     

Numerical simulations of a filament in a flowing soap film

Experiments concerning the properties of soap films have recently been carried out and these systems have been proposed as experimental versions of theoretical two‐dimensional liquids. A silk filament introduced into a flowing soap film, was seen to demonstrate various stable modes, and these were, namely, a mode in which the filament oscillates and one in which the filament is stationary and aligns with the flow of the liquid. The system could be forced from the oscillatory mode into the non‐ oscillatory mode by varying the length of the filament. In this article we use numerical and computational techniques in order to simulate the strongly coupled behaviour of the filament and the fluid. Preliminary results are presented for the specific case in which the filament is seen to oscillate continuously for the duration of our simulation. We also find that the filament oscillations are strongly suppressed when we reduce the effective length of the filament. We believe that these results are reminiscent of the different oscillatory and non‐oscillatory modes observed in experiment. The numerical solutions show that, in contrast to experiment, vortices are created at the leading edge of the filament and are preferentially grown in the curvature of the filament and are eventually released from the trailing edge of the filament. In a similar manner to oscillating hydrofoils, it seems that the oscillating filaments are in a minimal energy state, extracting sufficient energy from the fluid to oscillate. In comparing numerical and experimental results it is possible that the soap film does have an effect on the fluid flow especially in the boundary layer where surface tension forces are large. Copyright © 2004 John Wiley & Sons, Ltd.     

LINEAR ACTIVE STRUCTURES AND MODES (Ⅱ)--DISCRETE SYSTEMS AND BEAMS

The basic concepts about the active structures and some attributes of the modes were presented in paper "Liner Active Structures and Modes ( Ⅰ ) ". The characteristics of the active discrete systems and active beams were discussed, especially, the stability of the active structures and the orthogonality of the eigenvectors. The notes about modes were portrayed by a model of a seven-storeyed building with sensors and actuators. The concept of the adjoint active structure was extended from the discrete systems to the beams that were the representations of the continuous structures. Two types of beams with different placements of the measuring and actuating systems were discussed in detail. One is the beam with the discrete sensors and actuators, and the other is the beam with distributed sensor and actuator function. The orthogonality conditions were derived with the modal shapes of the active beam and its adjoint active beam. An example shows that the variation of eigenvalues with feedback amplitude for the homo-configuration and non-homo-configuration active structures.     

Measurements of Time-Varying Characteristics of Optical Signals and Inhomogeneities of Tested Substances with Additional Phase Modulation

The problem of investigation of the amplitude and phase structure of a time-varying probing optical signal and the structure of time-varying inhomogeneities of a substance tested by this signal is considered. The analysis is concerned, in particular, with determination of the structure of signals and processes with resolution in the pico- and femtosecond range. The scheme used for the analysis is based on registration of four spatially separated spectra of the studied radiation. The spectra are formed in a four-channel scheme with a twin-wave Michelson interferometer and a spectral device. Modulators based on electrooptical crystals (perovskites) are placed in the channels. The sum spectra are formed: without modulators, with the effect of either of the modulators, and with both of them affecting the radiation. The effect of the studied substance implies either modulating the radiation (in this case it is described by multiplication) or redistributing the radiation (then it is described by convolution).     

Dependence of the kinetics of the anionic polymerization of methyl methacrylate on the concentration in active centers

Studies on the anionic polymerization of methyl methacrylate in tetrahydrofuran and in the presence of sparteine have revealed a beneficial effect due to this additive, resulting in a decrease in the extent of termination. Better control of the definition of the polymers formed can thus be achieved in the presence of this additive. On the other hand, macromolecular engineering requires a range of active species concentrations lower than 10^?3 mol L^?1 and particularly the synthesis of polymers of high molar masses. For a better understanding of the mechanism of chain growth under such concentration conditions, the kinetics of polymerization have been investigated with a technique based on adiabatic calorimetry. Sparteine has been found to lack sufficient cation‐binding power to prevent the propagating enolate ion pairs from aggregating. The rate constant of propagation of nonaggregated species has been estimated, as well as the aggregation constant of equilibrium. For very low initiator concentrations, termination reactions have been shown to profoundly alter the control of the polymerization and to prevent a quantitative monomer conversion. Theoretical maximal conversions have been calculated from kinetic data and compare well with the experimental values. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4964–4975, 2004