First-principle studies on the electronic structure of Fe3O4(110) surface

The first-principle was employed to study the six possible models for the Fe₃O₄(110) surface, namely the AB-terminated surface (AB model), the AB-terminated with Fe_A vacancy (AB-Fe_A vac model), the AB-terminated with Fe_B vacancy (AB-Fe_B vac model), the B-terminated surface (B model), the B-terminated surface with Fe_B vacancy (B-Fe_B vac model) and the B-terminated surface with O vacancy (B-O vac model). The stability, the electronic structure and the magnetic properties of the six surface models were also calculated. The results predict that the B-O vac model is more stable than other types of surface models. The half-metallic property remain in the AB and B models, while the other four surface models exhibit metallic properties. At the same time, the AB, AB-Fe_A vac, AB-Fe_B vac, B and the B-Fe_B vac models have ferrimagnetic properties, while the B-O vac model has antiferromagnetic property.      

Kerr效应对非线性J-C模型辐射谱的影响

研究了Kerr介质腔中非线性J-C模型的辐射谱.导出了双模初始光场处于任意量子态时辐射谱的计算公式,给出了光场处于数态、相干态和压缩真空态时的数值结果,讨论了Kerr效应和初始场强对辐射谱的影响.发现在光子数态的情况下,Kerr效应使低频峰增强、高频峰减弱,并使各峰向右移动.在初始腔场为较强的相干态时,原子辐射谱明显地分成两个拱形的梳状峰群,Kerr效应的增强使左侧峰群增高,右侧的边峰受到抑制.在压缩真空态情况下,边带峰只出现在中心频率双峰的左侧,随Kerr效应和初始场的增强,边峰个数也随之增多.无论哪种情况都破坏谱结构的对称性,在强场条件下Kerr效应的影响更加显著.     

基于FPGA的超高速线阵CCD信号采集系统的设计与实现

线阵CCD已广泛应用于在线检测、图像识别等系统,目前高帧率采集系统多在200~500Hz之间。高速线阵CCD采集系统,如1K甚至10KHz以上的采集要求,设计难度大,电路实现复杂,需要专用处理器,产品成本高,提出了一种采用并行高速FPGA驱动线阵CCD,通过常规分立元件完成模拟信号处理,实现数字信号实时传输的方案。该方案不仅简化了硬件设计上的难度,在同等性能情况下,可实现每秒万帧的高速采样,大幅度降低了成本。方案选用Altera FPGA作为控制核心,实现高速信号采集的同时,在片上实现一定的图像算法,不仅加速了图像处理速度,同时降低了计算机的处理压力。最后,本电路通过USB2.0接口,完成数据的实时传输。设计具有高帧率、高灵敏度、性能稳定,便携使用等特点,同时还有一定的通用性,已应用于一些光学系统中。     

象面全息无损检测的实验研究

本文对象面全息无损检测方法进行了实验研究,结果表明该方法可用白光再现;同时,对于小缺陷可进行放大成象,从而提高了对小缺陷的判别精度。     

强激光装置中玻璃疵病在线检测的光学系统设计

介绍了一种用于玻璃疵病在线检测的近摄工作距成像光学系统,其光组结构形式采用了光阑后置的准远心结构形式,主要光学参量为f′=14 mm;在物像距为250 mm约束条件下,物方视场达到90 mm（对角线）;F/number=3.56;光谱适应范围为400~800 nm,对应的空间分辨率为100 lp/mm时,调制传递函数大于0.29.     

等效道路线声源位置优化研究

计算道路交通噪声时,一般将每个车道等效为1个线声源。有时,为了简化计算,将道路等效为1个线声源,等效线声源位置为道路中轴;或等效为2个线声源,等效线声源位置为道路两侧中心线或两侧最外车道中心线。推导不同等效方法下观测点噪声的计算公式,并探讨不同等效方法引起的误差。研究结果表明,将道路等效为2个线声源,等效线声源位置为道路两侧中心线的简化方法引起的误差最小。     

从机械能守恒的角度推导单摆简谐振动的周期

本文给出了利用基本的物理原理结合高等数学公式的方法推导单摆做简谐运动的周期公式,可以简明扼要地理解单摆简谐运动的过程.     

Calculation of the reactor neutron time of flight spectrum by convolution technique

It is a very complex and time-consuming process to simulate the nuclear reactor neutron spectrum from the reactor core to the export channel by applying a Monte Carlo program. This paper presents a new method to calculate the neutron spectrum by using the convolution technique which considers the channel transportation as a linear system and the transportation scattering as the response function. It also applies Monte Carlo Neutron and Photon Transport Code （MCNP） to simulate the response function numerically. With the application of convolution technique to calculate the spectrum distribution from the core to the channel, the process is then much more convenient only with the simple numerical integral numeration. This saves computer time and reduces some trouble in re-writing of the MCNP program.     

光谱成像技术无损鉴别西洋参饮片的研究

应用电可控液晶光谱成像装置,测定不同市售来源的西洋参饮片,以期为其质量控制提供新的方法。系统光谱分辨率5nm,光谱覆盖范围为405～680nm,空间分辨率50lp·mm-1。从成像光谱立方体中提取特征光谱曲线,构建饮片指纹图谱;采用主成分等聚类分析方法解析其指纹图谱,用于饮片真伪鉴别与质量判定。结果与性状,显微及理化鉴定结果相吻合。表明光谱成像分析技术可用于中药指纹图谱的构建和质量评价,操作方法简便、快速、无损。     

Detection of delamination defects in CFRP materials using ultrasonic signal processing

In this paper, signal processing techniques are tested for their ability to resolve echoes associated with delaminations in carbon fiber-reinforced polymer multi-layered composite materials (CFRP) detected by ultrasonic methods. These methods include split spectrum processing (SSP) and the expectation-maximization (EM) algorithm. A simulation study on defect detection was performed, and results were validated experimentally on CFRP with and without delamination defects taken from aircraft. Comparison of the methods for their ability to resolve echoes are made.