Voltammetry in Undiluted Acetic Acid. In Situ Determination of Water

Water present in undiluted acetic acid can be monitored in situ with Pt and Au microelectrodes using differential pulse and square‐wave voltammetries. Both reduction and oxidation peaks can be obtained. The best quantitative analytical results were obtained for the anodic peak, the Pt microelectrode, and differential pulse voltammetry. The anodic water peak is located at +1.55 V vs. the quasi reference Pt electrode. The voltammetric peak obtained at Pt electrode is apparently not a diffusional one, however, the calibration plot obtained by employing this peak is linear over a wide concentration range, up to 4 mol dm^?3. The detection limit has been estimated as 2.3 mM or 0.0043 v/v%. The developed method may be particularly useful, since the Karl Fischer method can not be used to determine water in glacial acetic acid due to the estrification reaction of acetic acid with methanol. A voltammetric wave of undiluted acetic acid could not be obtained in the positive and negative ranges of potential.     

Differential pulse polarographic determination of salicylaldehyde as its Girard-P derivative

A method for the determination of salicylaldehyde (2 × 10^–6–10^–4 M) by differential-pulse polarography, based on the in situ formation of its Girard-P derivative in aqueous solution at pH 2.5, is proposed. The relative standard deviation was 1.5% (ten determinations of 4 × 10^–5 M level). The applicability of this method was checked in synthetic samples containing salicyl alcohol,o-aminophenol, 2-methylphenol, salicylic acid and 4-aminobenzoic acid.     

Simultaneous Determination of Aluminum and Iron in High Salt Content Matrices by Adsorptive Stripping Voltammetry. Application to Dialysis Fluids

A new analytical procedure for the simultaneous determination of aluminum(III) and iron(II) in two kinds of dialysis fluids (peritoneal and hemodialysis fluids) by differential pulse adsorptive stripping voltammetry (DPAdSV) is described. The voltammetric measurements were performed using, as working electrode, a stationary mercury electrode, and a platinum electrode and a Ag|AgCl|KCl_(sat.) electrode as auxiliary and reference electrodes, respectively, employing acetate buffer solutions at different pH as supporting electrolyte. As complexing agents, Solochrome Violet RS, Palatine Chrome Black 6BN, Chromazurol S and Eriochrome Black T were employed. For both elements, the accuracy, expressed as relative recovery R%, was very satisfactory being in the range 94–105%, the precision as repeatability, expressed as relative standard deviation s_r%, was lower than 6%, while the limits of detection were of the order of a few units of μg/L. The analytical voltammetric procedure has been validated by comparison with spectroscopic (graphite furnace atomic absorption spectroscopy, GFAAS) measurements.     

Photoinduced Electron Transfer between CdS and CdTe Nanoparticles in Colloidal Solutions

The photochemical behavior of solutions containing a mixture of CdS and CdTe nanoparticles under pulsed irradiation conditions was investigated. It was shown that electron transfer from the CdS particles to the CdTe nanoparticles occurs during the photoexcitation of such systems. The effectiveness of the process is increased with increase in the size of the CdTe nanoparticles. Such behavior is due to decrease in the potential of the CdTe conduction band with increase in the size of the nanoparticles as a result of the appearance of quantum-dimensional effects.     

Differential pulse voltammetric determination of trace Te(IV) at a poly(3,3′-diaminobenzidine) film modified gold electrode in flow systems

Electropolymerization of 3,3′-diaminobenzidine on a gold surface gave an adherent, stable film of poly(3,3′-diaminobenzidine) (PDAB). This polymer film retained the complexational functionalities of its monomer, demonstrating preconcentration abilities for several ions, including Se(IV) and Te(IV). In particular, in this work, continuous flow and flow injection methods were developed for the sensitive and selective determination of Te(IV). The optimized method for the continuous flow mode had a detection limit of 5.6×10⁻⁹ mol l⁻¹ for 10 min preconcentration. Typical relative standard deviations for six consecutive determinations were 1.82 and 2.56% for Te(IV) concentrations of 1.0×10⁻⁶ and 5.0×10⁻⁸ mol l⁻¹, respectively (10 min preconcentration). The method was applied to the determination of Te(IV) in real samples.     

Simultaneous determination of lead(II) and cadmium(II) at a diacetyldioxime modified carbon paste electrode by differential pulse stripping voltammetry

A simple and effective chemically modified carbon paste electrode (CMCPE) for the simultaneous determination of lead(II) and cadmium(II) was developed in this work. The electrode was prepared by the addition of diacetyldioxime into a carbon paste mixture. Pb²⁺ and Cd²⁺ were preconcentrated on the surface of the modified electrode by complexing with diacetyldioxime and reduced at a negative potential (−1.10 V). Then the reduced products were oxidized by differential pulse stripping. The fact that two stripping peaks appeared on the voltammograms at the potentials of −0.65 V (Cd²⁺) and −0.91 V (Pb²⁺) demonstrates the possibility of simultaneous determination of Pb²⁺ and Cd²⁺. Under the optimized working conditions, calibration graphs were linear in the concentration ranges of 1.0×10⁻⁷-1.5×10⁻⁵ mol l⁻¹ (Pb²⁺) and 2.5×10⁻⁷-2.5×10⁻⁵ mol l⁻¹ (Cd²⁺), respectively. For 5 min preconcentration, detection limits of 1×10⁻⁸ mol l⁻¹ (Pb²⁺) and 4×10⁻⁸ mol l⁻¹ (Cd²⁺) were obtained at the signal noise ratio (SNR) of 3. To evaluate the reproducibility of the newly developed electrode, the measurements of 5×10⁻⁷ mol l⁻¹ Pb²⁺ and Cd²⁺ were parallel carried out for six times at different electrodes and the relative standard deviations were 2.9% (Pb²⁺) and 3.2% (Cd²⁺), respectively. Interferences by some metals were investigated. Only Ni²⁺ and Hg²⁺ apparently affected the peak currents of Pb²⁺ and Cd²⁺. The diacetyldioxime modified carbon paste electrode was applied to the determination of Pb²⁺ and Cd²⁺ in water samples. The results indicate that this electrode is sensitive and effective for the simultaneous determination of Pb²⁺ and Cd²⁺.     

Electrocatalytic Determination of Ascorbic Acid at the Surface of 2,7‐Bis(ferrocenyl ethyl)fluoren‐9‐one Modified Carbon Paste Electrode

A chemically modified carbon paste electrode with 2,7‐bis(ferrocenyl ethyl)fluoren‐9‐one (2,7‐BFEFMCPE) was employed to study the electrocatalytic oxidation of ascorbic acid in aqueous solution using cyclic voltammetry, differential pulse voltammetry and chronoamperometry. The diffusion coefficient (D=1.89×10^?5 cm² s^?1), and the kinetic parameter such as the electron transfer coefficient, α (=0.42) of ascorbic acid oxidation at the surface of 2,7‐BFEFMCPE was determined using electrochemical approaches. It has been found that under an optimum condition (pH 7.00), the oxidation of ascorbic acid at the surface of such an electrode occurs at a potential about 300 mV less positive than that of an unmodified carbon paste electrode. The catalytic oxidation peak currents show a linear dependence on the ascorbic acid concentration and linear analytical curves were obtained in the ranges of 8.0×10^?5 M–2.0×10^?3 M and 3.1×10^?5 M–3.3×10^?3 M of ascorbic acid with correlation coefficients of 0.9980 and 0.9976 in cyclic voltammetry and differential pulse voltammetry, respectively. The detection limits (2δ) were determined to be 2.9×10^?5 M and 9.0×10^?6 M with cyclic voltammetry and differential pulse voltammetry, respectively. This method was also examined for determination of ascorbic acid in pharmaceutical preparations.     

The Crystal Structure of Sr2TiSi2O8

Sr₂TiSi₂O₈ single crystals were grown by Czochralski pulling and from a high-temperature solution. X-ray diffractometry revealed the modulated crystal structure of Sr₂TiSi₂O₈ to belong to the 5D superspace group P4bm (−α, α, 1/2; α, α, 1/2) with α=0.3. Atomic positions, anisotropic displacement factors and positional modulation parameters for Sr₂TiSi₂O₈ are determined and discussed. The positional modulation is further investigated by electron diffraction and high-resolution transmission electron microscopy. In the latter experiments, the 2D modulation appears to be superimposed by some 1D modulation waves. This effect is discussed in terms of growth conditions.     

一阶导数差示脉冲极谱法用于甲硝唑的定量研究

本实验运用一阶导数差示脉冲极谱法对甲硝唑及其制剂进行了定量研究。在０．００１ｍｏｌ／Ｌ氯化钾－０．００１ｍｏｌ／Ｌ盐酸－水（１＋０．２＋４８）的底液中，甲硝唑于－０．８００Ｖ（ｖｓ Ａｇ／ＡｇＣｌ）处出现一良好的一阶导数差示脉冲极谱峰，在５０～３００μｇ／ｍＬ范围内，药物浓度与其导数峰幅值呈线关系，检测限为８．０×１０＾－８ｍｏｌ／Ｌ。本法操作简便，快速，灵敏，结果准确。     

Voltammetric behavior and determination of bismuth on sodium humate modified carbon paste electrode

The preconcentration and voltammetric behavior of Bi^III on a sodium humate modified carbon paste electrode was studied by means of cyclic voltammetry (CV) and differential pulse stripping voltammetry (DPSV). The proposed measurement involves an initial nonelectrolytic preconcentration step in which Bi^III is complexed by the surface modifier in a solution of 0.05 M KNO₃-0.0106 M HNO₃ (pH 2.0) and a subsequent electrochemical scan step in which the preconcentrated Bi^III was reduced and then oxidized promptly in supporting electrolyte of 0.5 M HNO₃. The resulting DPSV anodic current was proportional to the concentration of Bi^III ion over the range of 4.78 × 10⁻⁸–1.44 × 10⁻⁵ M. The detection limit was 4.78 × 10⁻⁸ M. The proposed method was used to determine bismuth in various samples. Various factors affecting the electrode behavior were also investigated at the same time.