高功率激光驱动器中小尺度自聚焦和噪声模型

 建立了一套线性的近似分析方法，研究高功率激光驱动器中强激光传输的小尺度自聚焦效应和相位噪声对光束传输和光束质量的影响，给出了系统噪声强度、B积分值与光束近场调制对比度之间的定量关系。研究表明,为保证输出光束质量，即近场调制对比度小于给定值，系统内的噪声强度必须符合一定的谱分布。     

高功率飞秒脉冲激光器的进展

概述了超短激光脉冲技术发展的历程。详尽的论述了啁啾脉冲放大技术的原理和一些关键技术 ,并对当今飞秒激光器研究发展的状况进行了综述。在分析其应用前景的基础上 ,进一步指出了这一技术领域未来的发展趋势。结果表明 ,脉冲激光放大系统以后的发展方向是 :更短脉冲 ;追求更高峰值功率 ;连续光谱调谐化 ;向小型化乃至全光纤化发展。     

高功率横流CO2激光器脉冲预电离过程研究

本文给出了对高功率横流CO_2激光器脉冲预电离过程的理论和实验研究.表明了预电离过程中光电离的重要作用.实验结果表明,脉冲预电离可增大高功率横流CO_2.激光器的pd值(p为放电气压、d为放电间隔),增大放电区注入功率密度.对于提高此类型激光器的放电稳定性和输出激光功率是一种技术简单而有效的手段.     

Analysis method of the effect of fabrication errors on a planar waveguide demultiplexer

The impact of fabrication errors on a planar waveguide demultiplexer is analyzed based on an analytical method. The explicit expression of the transfer function taking into account phase and amplitude errors is presented in order to analyze the loss and crosstalk of the demultiplexer caused by fabrication errors. A basic requirement for the demultiplexer with a certain crosstalk criterion can be easily obtained. Using an etched diffraction grating demultiplexer as an example, it is shown that the analytical results have a good agreement with results from a numerical method.     

e-A深度非弹性散射中胶子辐射振幅的新计算方法

在e-A深度非弹性散射过程中, 喷注穿过冷核介质时, 多重散射诱导胶子辐射会导致对碎裂函数的修正及喷注的能量损失.前期研究中关于计算e-A深度非弹性散射中胶子辐射振幅的两种方法: 螺旋振幅近似和微扰QCD严格计算都异常繁杂. 本文发展了一种新的方法, 可以方便计算出多重散射导致胶子辐射的振幅, 得到的碎裂函数的修正以及能量损失与严格计算的结果一致.     

Unified approach to photo-and electro-production of mesons with arbitrary spins

A new approach to identify the independent amplitudes along with their partial wave multipole expansions, for photo-and electro-production is suggested, which is generally applicable to mesons with arbitrary spin-parity. These amplitudes facilitate direct identification of different resonance contributions.      

用于ψ＇→γ＇xcJ→γ＇γJ/ψ过程中多极分析的产生子

为了实验研究粲偶素ψ＇级联衰变过程ψ＇→γ＇xcJ→γ＇γJ/ψ,一个用于正确描述全部末态角分布的产生子是必要的．可以通过分析角分布的关联来确定这一过程的多极展开参数（或者等效的螺旋度振幅），而从中可以知道高阶电磁多极矩和相对论修正的贡献，同时可以检验ψ＇是不是ψ＇（2S）和ψ＇（1D）的混合．介绍了一个能完全描述这一过程的角分布的产生子，同时讨论了测量多极参数的测量方法．这些都可以被用在BESⅢ或者CLEOc的分析当中．     

Mode beating in spot-size converter lasers

An anomalous modulation in the wavelength spectrum has been observed in lasers with spot-size converters. This intensity modulation is shown to be caused by beating between the fundamental lasing mode and radiation modes in the taper. This results in a periodic modulation in the net gain spectrum, which causes wavelength jumps between adjacent net gain maxima, and a drive current dependent spectral width that is expected to affect system performance. The amplitude of this spectral modulation is reduced significantly by either using an angled rear-facet which reflects the beating radiation modes away from the laser axis, or by using a nonlinear, adiabatic taper.     

介质极化的瞬时相位与振幅

求解电子运动的二阶微分方程，在旋转波近似下，介质在外场突然变化时产生的瞬态感应极化与外场同频，但相位总是落后，最大落后为π/2；振幅大小与初态有关，随时间按指数规律衰减，衰减快慢由介质的阻尼系数决定。     

Property improvement of pulsed laser deposited boron carbide films by pulse shortening

Growth characteristics and surface morphology of boron carbide films fabricated by ablating a B₄C target in high vacuum with a traditional KrF excimer laser and a high brightness hybrid dye/excimer laser system emitting at the same wavelength while delivering 700 fs pulses are compared. The ultrashort pulse processing is highly effective. Energy densities between 0.25 and 2 J cm⁻² result in apparent growth rates ranging from 0.017 to 0.085 nm/pulse. Ablation with nanosecond pulses of one order of magnitude higher energy densities yields smaller growth rates, the figures increase from 0.002 to 0.016 nm/pulse within the 2-14.3 J cm⁻² fluence window. 2D thickness maps derived from variable angle spectroscopic ellipsometry reveal that, when ablating with sub-ps pulses, the spot size rather than the energy density determines both the deposition rate and the angular distribution of film material. Pulse shortening leads to significant improvement in surface morphology, as well. While droplets with number densities ranging from 1 × 10⁴ to 7 × 10⁴ mm⁻² deteriorate the surface of the films deposited by the KrF excimer laser, sub-ps pulses produce practically droplet-free films. The absence of droplets has also a beneficial effect on the stoichiometry and homogeneity of the films fabricated by ultrashort pulses.