高功率横流CO2激光器脉冲预电离过程研究

本文给出了对高功率横流CO_2激光器脉冲预电离过程的理论和实验研究.表明了预电离过程中光电离的重要作用.实验结果表明,脉冲预电离可增大高功率横流CO_2.激光器的pd值(p为放电气压、d为放电间隔),增大放电区注入功率密度.对于提高此类型激光器的放电稳定性和输出激光功率是一种技术简单而有效的手段.     

Angular distributions of CH3I fragment ions under the irradiation of a single pulse and trains of ultrashort laser pulses

The angular distribution of CH3I is investigated experimentally using a single Fourier transform-limited laser pulse and a pulse train, where a 90-fs 800-nm linearly polarized laser field with a moderate intensity of 2.8×1013 W/cm2 is used. The dynamic alignment is demonstrated in a single pulse experiment. Moreover, a pulse train is used to optimize the molecular alignment, and the alignment degree is almost identical to that with the single pulse. The results are analysed by using chirped femtosecond laser pulses, and it demonstrates that the structure of pulse train rather than its effective duration is crucial to the molecular alignment.     

Improving attosecond pulse reflection by large angle incidence for a periodic multilayer mirror in the extreme ultraviolet region

The improvement of attosecond pulse reflection by large angle incidence for a periodic multilayer mirror in the extreme ultraviolet region has been discussed. Numerical simulations of both spectral and temporal reflection characteristics of periodic multilayer mirrors under various incident angles have been analyzed and compared. It was found that the periodic multilayer mirror under a larger incidence angle can provide not only higher integrated reflectivity but also a broader reflection band with negligible dispersion, making it possible to obtain better a reflected pulse that has a higher pulse reflection efficiency and shorter pulse duration for attosecond pulse reflection. In addition, by increasing the incident angle, the promotion of attosecond pulse reflection capability has been proven for periodic multilayer mirrors with arbitrary layers.     

基于耦合Duffing振子的局部放电信号检测方法研究

以双向环形耦合Duffing振子系统为对象, 研究脉冲信号激励下耦合振子间动力学行为变化特征时, 发现其与单向环形耦合Duffing振子系统类似, 在一定的参数条件下, 脉冲信号能引起其中一个振子与其他振子运动轨迹间出现短暂失同步的现象即瞬态同步突变现象. 基于这种现象, 提出了一种微弱脉冲信号检测的新方法, 用于检测强噪声背景中的局部放电脉冲信号. 实验测试表明, 利用本文方法对不同放电电极的局部放电脉冲信号进行检测时, 在低信噪比条件下可取得良好的检测效果, 进而扩展了现有的Duffing振子对非周期信号的检测范围及应用领域. 关键词： 耦合Duffing 振子 微弱信号检测 瞬态同步突变 局部放电脉冲信号     

可调脉冲宽度的调Q掺铥双包层光纤激光器

在激光器输出平均功率一定的情况下,峰值功率主要取决于调制频率和脉冲宽度。这使得脉冲宽度的调节具有一定的实际应用价值。对调Q掺铥双包层光纤激光器进行研究,首先确定了激光器的最佳输出透过率,在65%最佳透过率时,得到2 m激光的输出功率3.9 W,斜率效率为31%。外接一个信号发生器,信号门宽从12 s变化到18 s,并测量了调制频率分别在30 kHz、40 kHz和50 kHz时输出脉冲宽度的变化情况,得到了555.6 W的最高峰值功率,实现了脉冲宽度从163.4 ns到207.9 ns的变化。实验情况证实了用外接信号发生器能有效控制激光器的输出脉冲宽度。     

Laser drilling of thick material using femtosecond pulse with a focus of dual-frequency beam

Laser drilling is one of the basic, most frequently performed, material removal processes. The drilling aspect ratio is theoretically limited by the size and the focal depth of the machining laser spot. The aspect ratio can be improved by using dual focus. In this paper we describe a focus of two different frequencies based on the longitudinal chromatic aberration arisen when polychromatic collimated light is incident on a positive lens element. In the experiments, a Ti:Sapphire laser of 800 nm wavelength and 150 fs pulse duration was used as a source. Two tightly focused laser spots few hundred micrometers apart from each other were formed by focusing a combined collimated laser beam which contains the fundamental optic frequency and the second harmonic optic frequency. The focus of dual-frequency beam was used to drill a 3 mm thick PMMA plate. The drilling aspect ratio of a dual-frequency beam was compared to that of a focus of single frequency beam. Experimental results reveal that dual-frequency beam increases the aspect ratio and improves the drilling quality in terms of profile of the produced features.     

888 nm LD抽运Nd∶YVO4被动锁模皮秒振荡器

报道了基于888 nm半导体抽运Nd∶YVO4晶体连续被动锁模的皮秒振荡器。通过热激发抽运方式改善激光器的热性能,提高锁模振荡器输出的平均功率与单脉冲能量。利用半导体可饱和吸收体(SESAM)实现激光器锁模运转的启动与维持。在抽运功率为60 W时,获得最大输出功率为15 W,重复频率为53 MHz的皮秒脉冲输出,光-光转换效率为24%。在输出功率为15 W时脉冲宽度为45 ps。     

脉冲敲击技术对PI微球表面粗糙度的影响

作为点火靶重要候选靶丸之一, 聚酰亚胺 (PI) 空心微球采用降解芯轴技术结合双单体气相沉积聚合法 (VDP) 制备. 在PI涂层过程中微球碰撞对表面质量影响较大, 为了减小碰撞提高表面质量, 选用筛网盘做样品盘, 激励方式由压电振动模式改为脉冲敲击模式进行对比. 实验数据表明微球运动过程中碰撞是引起表面质量变差的原因, 通过理论分析确认了筛网盘通过减少接触点可以减少微球与微球间、微球与样品盘间的碰撞, 并且将压电振动改为脉冲敲击模式可以减小微球碰撞次数. 脉冲敲击模式与压电振动模式相比, 其可控性、微球弹跳幅度、消除静电等方面均优于压电振动. 对于微球壁厚均匀性而言, 压电振动略好于脉冲敲击, 但相差较小. 单个微球的壁厚最大偏差前者为0.68 μm, 优于后者的0.73 μm; 单个微球壁厚平均值在同一批次内的最大起伏, 前者为0.26 μm, 优于后者0.57 μm. 白光干涉仪数据显示脉冲敲击起到了提高微球表面质量的作用, 其表面粗糙度Rq值由52–93 nm 减小到28–44 nm. 关键词： 脉冲敲击技术 聚酰亚胺靶丸 表面粗糙度 壁厚均匀性     

Microstructure and properties of Nb/Ta multilayer films irradiated by a high current pulse electron beam

Nb/Ta multilayer films deposited on Ti6Al4V substrate with Nb and Ta monolayer thicknesses of 30 nm, 120 nm, and 240 nm were irradiated by a high current pulse electron beam (HCPEB) to prepare Nb-Ta alloyed layers. The microstructure and the composition of the outmost surface of melted alloyed layers were investigated using a transmission electron microscope (TEM) equipped with an X-ray energy dispersive spectrometer (EDS) attachment. The Ta content of the alloyed surface layer prepared from the monolayer of thickness 30 nm, 120 nm, and 240 nm was ～ 27.7 at.%, 6.37 at.%, and 0 at.%, respectively. It was found that the Ta content in the alloyed layer plays a dominant role in the microstructure of the films. The hardness and the wear rate of the alloyed layers decrease with the increasing content of Ta in the surface layer.     

功率型白光LED的非线性混合调光方法

分析脉冲宽度调制(PWM)双通道输出白光LED的混合调光方法,建立PWM与混合光源输出的光通量和色温之间变化关系的非线性数学模型。基于Zig Bee无线通信模块CC2530作为双路PWM输出,控制以SN3350为核心的LED恒流驱动电源,完成占空比可调的暖白和冷白两路白光LED的色温和光通量混合调光控制系统设计,并通过高精度快速光谱辐射计HAAS-2000测试系统进行测试。实验结果表明,双路PWM能够较好地实现对LED色温和光通量的输出大小进行控制,混合光源相关色温在3 250~15 000 K范围内连续可调。理论计算与系统控制的光通量和色温存在的相对误差分别小于1.70%和8.50%。