Preparation of barium hexaferrite nanopowders by the sol-gel method, using goethite

A series of barium hexaferrite nanoparticles (BaO·nFe₂O₃) with different n values were prepared by the sol-gel method, using goethite and Ba carbonate as raw materials. Phase identification of the samples was investigated by X-ray diffraction (XRD). XRD investigations show that the samples with n=5 and calcined at temperatures higher than 875 °C are single-phase Ba ferrite. An average crystallite size of 22 nm was obtained for the single-phase sample with minimum calcining temperature of 875 °C, using the Scherrer's formula. The morphology of the samples was checked by transmission electron microscope (TEM) and magnetic properties were measured by a sensitive permeameter. The results show that the samples have nonzero coercivities, which shows the particle size are not less than the critical size of Ba ferrite and then are not superparamagnet.     

极化子效应对ZnS/CdSe量子点三阶极化率的影响

在有效质量近似下,利用量子力学的密度矩阵理论,采用无限深势阱模型,从理论上计算了考虑极化子效应后在导带子带间跃迁时ZnS/CdSe柱型核壳结构量子点二次电光效应(QEOE)和电吸收过程(EA)的三阶极化率。通过数值计算,分析了电子-LO声子和电子-IO声子相互作用对ZnS/CdSe柱型核壳结构量子点二次电光效应和电吸收过程的三阶极化率的影响。结果表明,极化子效应对二次电光效应的三阶极化率χ⁽³⁾_QEDE和电吸收过程的三阶极化率χ⁽³⁾_EA都有很大影响,并且影响的大小与量子点的尺寸大小有关。     

基于神经网络的电火花线切割工艺目标建模

利用BP神经网络技术建立了电火花线切割加工工况参数与工艺目标间的预测模型.以脉冲宽度、脉冲间隙、峰值电流、间隙电压及工件厚度等工况参数为网络输入,加工效率和表面粗糙度等工艺目标为网络输出,通过用样本数据对网络的训练,实现了对工艺目标的预测.试验结果表明:所建预测模型能较好地反映线切割机床的工艺规律,实现对指定切割条件下加工效率和表面粗糙度的预测,最大预测误差小于10%.     

La-Ce-TiO2纳米光催化剂的溶胶-微波法合成、谱学表征及其活性研究

以钛酸四丁酯为原料,采用溶胶-微波法(Sol-Microwave Method)合成了镧和铈共掺型纳米TiO2粉体(La-Ce-TiO2),借助XRD、XPS和UV-Vis等测试手段对其进行了表征,并以甲基橙为模型污染物考察了掺杂量对样品光催化活性的影响规律.XRD分析表明,所得粉体均为锐钛矿相纳米TiO2,且稀土元素镧和铈掺杂后纳米TiO2特征衍射峰宽化,强度降低;XPS分析表明,镧和铈掺杂后样品表面存在大量的氧缺位;UV-Vis吸收光谱表明,所得粉体在400 nm以下均有连续宽化的吸收带,且La和Ce掺杂后样品对光的吸收显著增强,这足由于La(Ⅲ)-O荷移跃迁以及Ce(Ⅳ)f→d跃迁和Ce(Ⅳ)-O荷移跃迁所致;光催化实验表明,La和Ce共掺杂能显著提高纳米TiO2的光催化活性,其中当La(Ⅲ)和Ce(Ⅳ)掺杂量分别为2%和0.04%时,纳米TiO2光催化剂具有较高的催化活性,自然光照射下光催化氧化处理卷烟厂蒸叶车间废水,效果较好,废水COD去除率达到86.11%.     

On radar accuracy using beam wave in random media

The accuracy of radar detection is measured in this paper through comparing the laser radar cross-section (LRCS) to RCS data for plane-wave incidence in free space. This is to study the performance of backscattering enhancement from conducting targets with finite size. LRCS is calculated using beam wave incidence propagating in a random medium. Targets are of large size with relatively complex cross-sections. E-wave polarization is assumed for incident waves in continuous random media with different spatial coherency.     

大学物理实验教学改革探索——谈“少台套大循环”教学模式与管理

教学改革的最终目标都是为了有益于学生的全面发展以及实践能力的提高。以大学物理实验改革为例,介绍了＂少台套大循环＂的实验改革与教学管理方法。经过两年多＂少台套大循环＂的运行,这种改革不仅提高了学生的实验操作能力,而且在教学资源有效配置方面探索出一种可行的运行模式。     

Effect of microstructure on the coercivity of HDDR Nd-Fe-B permanent magnetic alloy

The effect of the grain boundary microstructure on the anisotropy and coercivity was investigated in an HDDR Nd-Fe-B permanent magnetic alloy. Considering the special microstructure of its magnetic powder grain, an anisotropic theoretical model influenced simultaneously by the structure defect at the grain boundary and the exchange coupling interaction was put forward. The variations of the structure defect factors based on the nucleation and pinning mechanism with 2r ₀/lex (where r ₀ and lex are the defect thickness and the length of exchange coupling, respectively) were calculated. The results show that the coercivity mechanism of an HDDR Nd-Fe-B permanent magnetic alloy is greatly related to its microstructure defect at the grain boundary. For a fixed lex, when 2r ₀/lex < 1.67, the coercivity is controlled by the pinning mechanism; when 2r ₀/lex > 1.67, it is determined by the nucleation mechanism. The coercivity reaches the maximum when 2r ₀/lex = 1.67. The calculation result is consistent well with the experimental result given by Morimoto et al. Supported by the National Natural Science Foundation of China (Grant No. 50671055)     

液冷薄片构型激光器及其热管理技术

为了解决增益介质的热效应问题,提出了一种浸没式构型液冷激光器方案,该构型激光器在10Hz重复抽运频率下,获得了615mJ的能量输出,光光转换效率为21%,斜率效率为23%.基于流体力学和热力学原理,建立了激光器增益区流场的热-流-固耦合模型,利用软件模拟和有限元分析法,研究了在不同流速、泵浦功率条件下,整个增益区的温度场、速度场的分布特性;并基于增益区温度场的分布,分析了液冷条件下通过增益区的激光波前畸变特性.结果表明,增益介质的最大光程差为0.7666λ,冷却液最大光程差为-4.7331λ,说明该构型激光器有着良好的热管理性能.     

反向响应过程抗负载干扰PID控制回路性能评估

反向响应过程广泛存在于化工领域中,但针对反向响应过程的性能评估研究较少。针对一类二阶时滞反向响应过程,通过幂级数展开的方法简化了对象模型,然后研究其抗负载干扰PID控制回路性能评估问题。根据DS-d控制原理获取期望闭环传递函数以及PID控制器参数,推导干扰模型为阶跃情况下的PID控制回路累积绝对误差(IAE)性能基准值,并将其推广到斜坡输入以及一般输入情形,为不同干扰类型情况下的反向响应过程建立通用化的IAE性能评价标准。仿真结果验证了所提性能评估算法的正确性以及通用性。     

Doubly stochastic Yule cascades (Part I): The explosion problem in the time-reversible case

Motivated by the probabilistic methods for nonlinear differential equations introduced by McKean (1975) for the Kolmogorov-Petrovski-Piskunov (KPP) equation, and by Le Jan and Sznitman (1997) for the incompressible Navier-Stokes equations (NSE), we identify a new class of stochastic cascade models, referred to as doubly stochastic Yule cascades. We establish non-explosion criteria under the assumption that the randomization of Yule intensities from generation to generation is by an ergodic time-reversible Markov process. In addition to the cascade models that arise in the analysis of certain deterministic nonlinear differential equations, this model includes the multiplicative branching random walks, the branching Markov processes, and the stochastic generalizations of the percolation and/or cell ageing models introduced by Aldous and Shields (1988) and independently by Athreya (1985).