Effect of Drying Methods on the Structure and Combustion Activity of Mn—Substituted Hexaaluminate Catalysts

Conventional oven drying (COD) and supercritical drying (SCD) methods were applied to the preparation of Mn-substituted hexaaluminate (BaMnA111O19-α) catalysts. The effect of drying methods on phase composition, specific surface area, pore structure, reduction behavior of Mn^3 ions, and combus-tion activity of the samples was investigated. The homogenous mixing of the components in the sol-gel process could be maintained by SCD, and the hexaaluminate phase was almost the only phase of the resulting materials after calcination. H2-TPR revealed that the Mn^3 ions in the sample obtained by SCD were easier to be reduced than that by COD. Moreover, the samples obtained by SCD have higher surface area, narrower pore size distribution, and higher combustion activity than those obtained by COD.     

Methane Combustion Over Fe, Co and Ni Modified Manganese Oxide Catalysts

Fe-Mn, Co-Mn and Ni-Mn composite oxide catalysts based on high specific surface area MnO₂ precursor were prepared and applied to catalytic combustion of CH₄. Results were compared with that of unmodified MnOx and 1wt.% Pd/-Al₂O₃. Below 450°C, manganese oxide catalysts show higher activity than Pd/-Al₂O₃, while the modified manganese oxide catalysts exhibit higher activity than the unmodified one below 420°C. All catalysts were characterized by means of N₂-BET, XRD, TG-DTA and H₂-TPR. Due to the interaction between Fe, Co or Ni oxides and manganese oxide, the activity of the oxygen species of the modified catalysts is improved, which leads to the increase of their CH₄ combustion activity.     

Mechanistic study of thermal behavior and combustion performance of epoxy resins: I homopolymerized TGDDM

Tetraglycidyl 4,4′-diaminodiphenylmethane (TGDDM) undergoes homopolymerization on heating. Intramolecular reactions which compete with crosslinking favor the formation of cyclic structures with increasing thermal and fire resistance of the resin, whereas physical mechanical properties tend to decrease. The mechanism of thermal decomposition of TGDDM is studied by thermogravimetry, differential scanning calorimetry and thermal volatilization analysis with characterization of volatiles evolved and residue left. Thermal degradation of poly-(TGDDM) starts at 260°C with elimination of water from secondary alcoholic groups which is a typical pathway for epoxy resin degradation. Resulting unsaturations weaken bonds in the β-position and provoke the first chain breaking at allyl–amine and allyl–either bonds. With increasing temperature, saturated alkyl–ether bonds and alkyl carbon–carbon bonds are broken first, followed by the most stable alkyl–aryl bonds at T>365°C. The combustion performance of TGDDM is discussed on the basis of the thermal degradation behavior.     

Thermodynamic study of the three isomers of bromo and iodobenzoic acids. Part II

Using our technique of combustion of small amount of a substance, we determined by calorimetry the standard molar enthalpy of formation in the condensed state and atT=298.15 K of the three isomers of bromo and iodobenzoic acids. Associating to these values their standard molar enthalpies of sublimation previously measured, it was possible to determine their standard molar enthalpies of formation in the gaseous state and atT=298.15 K. The experimental values of the thermodynamic properties _f H _m ^o (cr, 298.15 K), _f H _m ^o (cr, 298.15 K), _sub H _m ^o (298.15 K), and _f H _m ^o (g, 298.15 K) are given for the two series. From the experimental value of the standard molar enthalpy of atomization, it was possible to determine an enthalpy value for the C_b-Br and C_b-I bonds. The experimental and theoretical values of the resonance energy of bromo and iodobenzoic acids are compatible. The relative stability of some monosubstituted derivatives of benzoic acid studied in our laboratory is also discussed.Part I is concerned with Ref. 22 (for bromobenzoic acids) and with Ref. 23 (for iodobenzoic acids).     

石油焦与煤混合燃料热重分析研究

石油焦与煤混合燃烧是高效处理石油焦的有效方法，作者对选用的石油焦和煤不同配比的混合燃料进行了热重分析研究。使用常压高温热天平研究、分析了各配比混合燃料的热解特性和燃烧特性。并根据化学动力学方法计算了各过程的化学动力学参数，即活化能E和频率因子A0。结果表明，各混合燃料热解起始温度大致相同，随煤焦比减小，挥发分析出速率变缓，最大释放速度所对应的温度升高，最终失重率减小，挥发分释放特性指数减小；随煤焦比增大，混合燃料着火温度和燃尽温度逐渐降低，最大燃烧速率所对应的温度降低，燃烧特性指数增大；随煤焦比减小，活化能和频率因子增大。     

Cu-Mg/Al复合氧化物催化碳颗粒物燃烧性能的研究

恒定二价与三价阳离子比为3(nM2+/nM3+=3),采用共沉淀法制备不同Cu含量的系列水滑石前驱物, 800 ℃焙烧4 h形成复合氧化物(CuO质量百分数分别为0％、5％、10％、15％、20％、30％、40％)用作柴油车排放碳颗粒物燃烧的催化剂,并采用XRD、BET、TG-DSC、FT-IR、TPR等表征手段研究了Cu、Mg含量对材料前驱物物化性能的影响及对其衍生复合氧化物催化碳颗粒物燃烧性能的影响．结果表明,Cu、Mg含量对材料的热稳定性、比表面和催化氧化活性有显著的影响. Mg有助于提高催化剂的热稳定性; Cu含量增加,催化剂比表面下降,但比表面不是影响催化剂活性的主要因素. CuO含量为15％时,催化剂具有最好的催化活性和稳定性,碳颗粒物的起燃温度(T10)和半转化温度(T50)分别为336 ℃和409 ℃.在CuO含量≤30％时可以形成结构完整的水滑石前驱物, CuO含量为40％时出现Cu(OH)2杂相; CuO含量< 20％时,经高温焙烧可得到均匀的复合氧化物, CuO含量≥20％时出现CuO偏析． TPR结果表明焙烧温度和复合氧化物的组成决定了材料的可还原性能．     

Thermodynamics of phenylated polyphenylene between 0 and 340 K

In an adiabatic vacuum calorimeter, the temperature dependence of the heat capacity C _p of phenylated polyphenylene and initial comonomer 1,4-bis(2,4,5-triphenylcyclopentadienone-3-yl)benzene was studied between 6 and 340 K with an uncertainty of about 0.2%. In a calorimeter with a static bomb and an isothermal shield their energies of combustion DUcomb were measured. From the experimental data, the thermodynamic functions C _p ⁰ (T), H ⁰(T)-H ⁰(0), S ⁰(T)-S⁰(0), G ⁰(T)-H ⁰(0) were calculated from 0 to 340 K, and standard enthalpies of combustion ΔH _comb ⁰ and thermodynamic parameters of formation-enthalpies ΔH _f ⁰, entropies ΔH _f ⁰, Gibbs functions ΔG _f ⁰ - of the substances studied were estimated at T=298.15 K at standard pressure. The results were used to calculate the thermodynamic characteristics (ΔH _f ⁰ ,ΔS _f ⁰, ΔG _f ⁰) of phenylated polyphenylene synthesis in the range from 0 to 340 K. This revised version was published online in July 2006 with corrections to the Cover Date.     

Thermochemistry of heteroatomic compounds 22. Enthalpies of combustion and formation of alkyl(aryl)arsines and arsenites in the condensed and gaseous phases

The enthalpies of combustion (ΔH _comb) of five primary, secondary, and tertiary alkyl(aryl)arsines in the condensed state were calculated using the equation ΔH _comb = −385.8–110.3N, where N is the number of bond-forming electrons. The dependence presented is used for the calculation of the enthalpies of combustion of full esters and amidoesters of arsinous acid of noncyclic and cyclic structures. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 1042–1043, May, 2007.     

Standard molar enthalpy of formation of CH<Subscript>3</Subscript>(CH<Subscript>3</Subscript>SCH<Subscript>2</Subscript>)SO,methyl methylthiomethyl sulfoxide

Summary The standard molar enthalpy of formation of methyl methylthiomethyl sulfoxide, CH₃(CH₃SCH₂)SO, at T=298.15 K in the liquid state was determined to be -199.4±1.5 kJ mol^-1 by means of oxygen rotating-bomb combustion calorimetry.     

Some thermodynamic aspects of nitrides in materials science

The energies of combustion in fluorine of gallium nitride and indium nitride in wurzite crystalline structure have been measured in a two-compartment calorimetric bomb, and new standard molar enthalpies of formation have been calculated: Δ_fH_m⁰(GaN(cr) 298.15 K)= –(163.7±4.2) kJ mol^–1 and Δ_fH_m⁰(InN(cr) 298.15 K)= –(146.5±4.6) kJ mol^–1 . Comparison with the recommended values of the Δ_fH_m⁰ nitrides from the literature is also presented.