Helium blistering of niobium: Large swelling measurements supporting the gas pressure model

Crystal potentials are usually obtained through a combination of theoretical calculation and the fitting of crystal properties. Because of thermal expansion of the crystal, the equilibrium condition is not satisfied at all temperatures unless the crystal potential is made temperature-dependent. A quasiharmonic potential that satisfies the equilibrium condition at all temperatures is derived from KC1 and used to calculate temperature-dependent defect energies (at constant volume). Other thermodynamic defect parameters are then derived by combining these results with the experimental Gibbs energies. The temperature-dependence of these parameters is displayed.     

Synthesis of a benzoxazine with precisely two phenolic OH linkages and the properties of its high‐performance copolymers

A phenolic OH‐containing benzoxazine ( F‐ap ), which cannot be directly synthesized from the condensation of bisphenol F, aminophenol, and formaldehyde by traditional procedures, has been successfully prepared in our alternative synthetic approach. F‐ap was prepared by three steps including (a) condensation of 4‐aminophenol and 5,5'‐methylenebis(2‐hydroxybenzaldehyde) (1) , (b) reduction of the resulting imine linkage by sodium borohydride, and (c) ring closure condensation by formaldehyde. The key starting material, (1) , was prepared from 2‐hydroxybenzaldehyde and s‐trioxane in the presence of sulfuric acid. F‐ap is structurally similar to bis(3,4‐dihydro‐2H‐3‐phenyl‐1,3‐benzoxazinyl)methane ( F‐a, a commercial benzoxazine based on bisphenol F/aniline/formaldehyde) except for two phenolic OHs. The phenolic OHs can provide reaction sites with epoxy and 1,1'‐(methylenedi‐p‐phenylene)bismaleimide (BMI). The structure–property relationships between the thermosets of F‐ap /epoxy, F‐a /epoxy, F‐ap /BMI, and F‐a /BMI were discussed. Experimental data showed that thermosets based on F‐ap /epoxy and F‐ap /BMI provided much better thermal properties than those based on F‐a /epoxy and F‐a /BMI. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2686–2694     

高效液相色谱法同时测定生物质乳酸发酵液中有机酸及糖类化合物

建立了高效液相色谱(HPLC)同时测定生物质乳酸发酵液中有机酸及糖类的分析方法。使用Bio-Rad Aminex HPX-87H色谱柱,以5 mmol/L的H2SO4为流动相,在柱温55 ℃,流速0.6 mL/min条件下,采用示差折光检测器进行检测。结果表明,该方法可在17 min内实现发酵液中各种有机酸和糖类化合物等的完全分离与定量,6种有机酸和3种糖类化合物在0.15～5.19 g/L范围内的线性关系良好,回归方程的线性相关系数在0.9998以上。将该法用于米根霉发酵液的检测,两个水平的加标回收率为96.91%～103.11%,相对标准偏差(n=6)为0.81%～4.61%。该法适用于微生物发酵液中多种有机酸和糖类的快速、高效分离和定量测定。     

Liquid Chromatograph Detector for Trace Analysis of Non-Volatile N-Nitroso Compounds

Abstract

A Thermal Energy Analyzer has been interfaced to a high performance liquid chromatograph. The hplc-TEA system can be used for analysis of nanogram amounts of N-nitroso compounds.     

反相高效液相色谱法制备银杏叶中聚戊烯醇同系物单体

利用制备高效液相色谱法从银杏叶中分离制备了聚戊烯醇同系物单体。在HiQ sil C18柱上,以异丙醇-甲醇-正己烷-水(体积比为50∶25∶15∶4)为流动相,流速10 mL/min,采用等度洗脱方式,制备了8种化合物,经紫外光谱、红外光谱及质谱分析,确认它们分别为C70,C75,C80,C85,C90,C95,C100和C105聚戊烯醇,其中主要成分为C85及C90聚戊烯醇。高效液相色谱分析表明,制备的C75C105聚戊烯醇化合物的纯度均在96%(质量分数)以上。在该色谱条件下,各色谱峰达到了基线分离,     

黄芩中黄芩苷的亚临界水提取及高效液相色谱分析

建立了黄芩药材中黄芩苷的亚临界水提取 高效液相色谱测定方法。分别考察了温度、压力、提取时间、提取物颗粒度、溶剂比等因素对提取量的影响,并与有机溶剂提取法比较。结果表明,当两者具有相同的提取效果时,亚临界水提取法的提取时间及提取溶剂的消耗量大大减少,避免了使用有机溶剂造成的污染。黄芩苷提取最佳条件为:样品颗粒度80～100目,溶剂比0.2 mL/mg ,5 MPa,130 ℃保持10 min。并通过提取 高效液相色谱联机分析实现了对提取物的实时监测。该技术有望成为从中药材中提取脂溶性成分的有效方法。     

Mechanochemical synthesis of PbS/Ni–Cr layered double hydroxide nanocomposite

1. Download : Download high-res image (140KB)
2. Download : Download full-size image

     

Microstructure,Tribological Behavior,and Corrosion-Resistant Performance of Bonded MoS2 Solid Lubricating Film Filled with Nano-LaF3

The anti-friction and wear-resistant performances of bonded MoS₂ solid lubricating films filled with nano-LaF₃ filler were investigated under in drying wear conditions, the corrosion-resistant performances of bonded lubricating films was evaluated according to ASTM-B117, and the characteristics of the bonded lubricating films were examined by TEM and elemental x-ray map. The wear-resistant performance of the bonded lubricating films filled with nano-LaF₃ filler increases with increasing content of nano-LaF₃ filler within a content range between 0 and 5 wt%, whereas the bonded lubricating films filled with 0.5–1 wt% micro-LaF₃ filler exhibit the better wear-resistant performances. The incorporation of both nano-LaF₃ and micro-LaF₃ filler leads the increase of the coefficient of friction of the bonded lubricating films. The LaF₃ filler can improve the corrosion-resistant performance of the bonded MoS₂ solid lubricating films, whereas the incorporation of nano-LaF₃ filler is more effective to improve the corrosion-resistant performance of the bonded lubricating films than micro-LaF₃ filler. The improvement in the wear-resistant and corrosion-resistant performances of the bonded lubricating films by the incorporation of the nano-LaF₃ filler is attributed to the strengthened interfacial bonding among the nano-LaF₃ and the MoS₂ lubricant and the polymeric matrix. However, a too high mass fraction of the nano-LaF₃ filler in the bonded lubricating films will increase surface and interface defects, and lead the worsening of corrosion-resistant performance of the bonded lubricating films.