Optical Phase Conjugation in Polyesters with Cyanoazobenzene Units in the Side Chain

Efficient optical phase-conjugate (PC) signals in four kinds of novel polyester films containing cyanoazobenzene units in the side chain are reported. One of them can efficiently generate only the photoinduced anisotropy (PA) component of PC signal, while the other three films can simultaneously generate two types of PC signals, PA and holographic components. These polymers have good potential not only as a phase conjugator but also as a polarization-sensitive hologram-recording material.Presented at the International Commission for Optics Topical Meeting, Kyoto, 1994     

Miscibility of Solution Blends of Unsaturated Polyester Resin with Polystyrene and Polycarbonate

Miscibility studies of unsaturated polyester resin (UPR) blends with two different thermoplastics—polystyrene (PS) and polycarbonate (PC), in a common solvent, chloroform, were carried out by viscosity, ultrasonic velocity, density, and refractive index methods. Two interaction parameters, μ and α were calculated using viscosity data for these blends. The positive interaction parameter values (μ and α > 0) obtained for the UPR/PS blend and the negative interaction parameter values (μ and α < 0) obtained for the UPR/PC blend indicate that the former is a miscible blend and the latter is an immiscible blend. These results were further confirmed by the ultrasonic velocity, density, and refractive index measurements.     

Rheological Characterization of Poly(3,3′-Diaminodiphenylsulfone Terephthaloylchloride) Solutions in Dimethylsulfoxide

Steadyshear and oscillatory shear rheological measurements were performed to characterize the solution rheological behavior of poly(3,3′-diaminodiphenylsulfone terephthaloylchloride) (P(3,3′-DDS-TPC)) in dimethyl sulfoxide (DMSO). The effects of temperature, concentration, and weight-average molar mass () on the rheological properties were investigated. From the temperature dependence of zero-shear viscosity, the flow activation energies, E_η, of P(3,3′-DDS-TPC)/DMSO solutions were calculated. Both the overlap concentration, C*, and the entanglement concentration, C_e, were determined from the concentration dependence of the specific viscosity η_sp. All the P(3,3′-DDS-TPC) solutions, we studied, can be separated into three regimes: the dilute, semidilute-unentangled, and entangled regime with slopes of 1, 1.3, and 3.9, of concentration versus η_sp plots, respectively, which are consistent with scaling predictions for flexible polymers in a good solvent.     

Two-step dissociation of a polaron in conjugated polymers

We have studied the electric-field-driven motion of a polaron by solving the time-dependent Schr\"{o}dinger equation nonadiabatically and the lattice equation of motion simultaneously. It is found that the polaron may experience two sequent transitions under high fields; one is the transition from the subsonic to the supersonic state, and the other from the supersonic to dissociated state. The acoustic mode is decoupled from the charge when the polaron moves at a speed faster than the sound speed, and then the optical mode is decoupled at the second transition to make the polaron dissociate completely.     

应用核磁共振进行聚驱后泡沫驱油特性研究

采用并联岩心进行聚驱后泡沫驱油实验,利用核磁共振技术,对驱替后岩心的不同直径孔隙内的流体分布进行了研究,得到了水驱、聚合物驱、泡沫驱替阶段的驱出油的孔径范围以及剩余油分布.实验结果表明,与水驱和聚合物驱相比,泡沫驱增大了波及的孔径的范围.泡沫可以在水驱和聚驱易发生窜流的大孔径通道形成封堵,从而波及到了水驱和聚驱未波及到的孔径,不但大幅度的提高了低渗岩心的采收率,也驱出了部分高渗岩心的小孔径的油.     

An Insight into the Diffusion of Unsaturated Polyester (UP) Resin into Expanded Graphite (EG) to Improve the Mechanical Properties of the UP/EG Composites

Abstract

Polymer/expanded graphite (EG) nanocomposites have great importance in many industrial applications mainly due to their high electrical/thermal conductivity or flame retardancy. However, to fully employ the benefits of polymer/EG nanocomposites one must consider the high degree of porosity of EG. The high degree of porosity of EG can deteriorate the composites’ mechanical properties if the polymer chains cannot diffuse completely into the EG pores. In this article, an insight is given into the diffusion of unsaturated isophthalic polyester (UP) resin, consisting of a combination of maleic anhydride and isophthalic anhydride in the resin backbone, with two viscosities, into the pores of the EG particles of various degrees of porosity. The diffusion experiments were carried out on compressed EG tablets with the same density but different porosity due to the different porosity of the EG particles. The results showed that the diffusion rate of the UP resin with higher viscosity slightly decreased when the EG porosity decreased but, in the opposite way, it strongly increased for the low viscosity UP resin. The EG nanocomposites samples were molded at varying pressures. The micrographs of the fractured surfaces of the EG nanocomposites showed that the EG pores were not filled with resin, thus the EG nanocomposites had residual pores. It was found that composites containing EGs with higher expansion ratio and larger particles and pores showed larger residual pores. Furthermore, the composites prepared with the more viscous UP resin showed more residual pores. By applying a pressure of 10?bar instead of 1?bar, a reduction of 7–20% in the residual pores of the nanocomposites was observed which led to improved mechanical properties by up to 20% in flexural strength for the EG with the highest expansion ratio.     

Designing N-halamine based antibacterial surface on polymers: Fabrication, characterization, and biocidal functions

We demonstrate a valuable method to generate reactive groups on inert polymer surfaces and bond antibacterial agents for biocidal ability. Polystyrene (PS) surfaces were functionalized by spin coating of sub-monolayer and monolayer films of poly(styrene-b-tert-butyl acrylate) (PS-PtBA) block copolymer from solutions in toluene. PS-PtBA self-assembled to a bilayer structure on PS that contains a surface layer of the PtBA blocks ordering at the air-polymer interface and a bottom layer of the PS blocks entangling with the PS substrate. The thickness of PtBA layer could be linearly controlled by the concentration of the spin coating solution and a 2.5 nm saturated monolayer coverage of PtBA was achieved at 0.35% (w/w). Carboxyl groups were generated by exposing the tert-butyl ester groups of PtBA on saturated surface to trifluoroacetic acid (TFA) to bond tert-butylamine via amide bonds that were further chlorinated to N-halamine with NaOCl solution. The density of N-halamine on the chlorinated surface was calculated to be 1.05 × 10⁻⁵ mol/m² by iodimetric/thiosulfate titration. Presented data showed the N-halamine surface provided powerful antibacterial activities against Staphylococcus aureus and Escherichia coli. Over 50% of the chlorine lost after UVA irradiation could be regained upon rechlorination. This design concept can be virtually applied to any inert polymer by choosing appropriate block copolymers and antibacterial agents to attain desirable biocidal activity.     

Exploring Microstructures and Interphase Properties of Surface- Grafted Diblock Copolymers in a Homopolymer Melt by Self-Consistent Field Theory Simulations

Polymeric self-consistent field theory is used to investigate microstructures and interphase properties of diblock copolymers grafted onto solid surfaces in a homopolymer melt. The calculations show that the grafted diblock copolymers can self-assemble into hemispherical microstructures at low grafting densities of the diblock copolymers. The morphology transforms into hemicylinder-like and sandwich-like lamellar microstructures with an increase in the chain-grafting density. The effective thickness of the grafted block layer and the interphase width between the homopolymer melt and the grafted copolymers strongly depend on the physicochemical parameters of the system, such as the composition of the grafted copolymer, the chemical incompatibility between the different components, the length ratio of grafted copolymer to homopolymer, and the grafting density of the diblock copolymers. In addition, the above computational results of microphase-separated structures and interphase properties are qualitatively compared with our previous experimental observations. The comparison indicates that our theoretical results not only reproduce the general feature of the experimental observations, but also elucidate the internal structural information and complement the findings in the region of high grafting densities of diblock copolymers.     

Percolation Thresholds in Ternary Polymer Melt Blends with Separate Dispersions of the Inner Phases: Mathematical Model

A mathematical model based on a straightforward geometrical background is developed which enables predictions of a transition of one dispersed phase to a cocontinuous one (i.e., the percolation threshold) on addition of another dispersed phase during melt mixing in ternary polymer blends. The present work concerns only ternary blends with two separate dispersions of the inner phases in which no encapsulation takes place. In addition, in order to simplify the model, one of the inner phases was represented by hard, nondeformable microspheres The expression developed describes well an experimental relationship between the percolation threshold, the concentration above which the former dispersed phase transforms to a continuous one, and concentrations of both inner phases. The results agree well with the experimental data obtained in a previous work.     

Deviation of Upper Bounds of Critical Temperature of Two-Dimensional O(N) Spin Models

Critical temperature of the classical O(N) spin model in two dimensions is investigated. We show that no phase transition exists in the system if the inverse temperature is less than _c=_c(N), where _c(N) is a constant such that _c(N) > const. N log N.