Separation of natural antioxidants using PDMS electrophoresis microchips coupled with amperometric detection and reverse polarity

This report describes the use of PDMS ME coupled with amperometric detection for rapid separation of ascorbic, gallic , ferulic, p‐coumaric acids using reverse polarity. ME devices were fabricated in PDMS by soft lithography and detection was accomplished using an integrated carbon fiber working electrode aligned in the end‐channel configuration. Separation and detection parameters were investigated and the best conditions were obtained using a run buffer consisting of 5 mM phosphate buffer (pH 6.9) and a detection voltage of 1.0 V versus Ag/AgCl reference electrode. All compounds were separated within 70 s using gated injection mode with baseline resolution and separation efficiencies between 1200 and 9000 plates. Calibration curves exhibited good linearity and the LODs achieved ranged from 1.7 to 9.7 μM. The precision for migration time and peak height provided maximum values of 4% for the intrachip studies. Lastly, the analytical method was successfully applied for the analysis of ascorbic and gallic acids in commercial beverage samples. The results achieved using ME coupled with amperometric detection were in good agreement with the values provided by the supplier. Based on the data reported here, the proposed method shows suitability to be applied for the routine analysis of beverage samples.     

Construction of a portable sample preparation device with a magnetic poly(methacrylic acid‐co‐ethylene dimethacrylate) monolith as the extraction medium and its application in the enrichment of UV filters in water samples

A portable sample preparation device with a magnetic polymer monolith as the extraction medium was constructed. The monolith was synthesized by polymerizing methacrylic acid and ethylene dimethacrylate around a cylindrical magnet. In this way, the monolith with a magnetic core could be readily attached to the extraction device by magnetism. The constructed device was evaluated for the enrichment of UV filters in water samples, followed by high‐performance liquid chromatographic analysis. The extraction efficiency for the targets was satisfactory with no matrix interference. Good linearities were obtained for the UV filters with the correlation coefficients >0.9986. The limits of detection and quantification for the UV filters were 0.3–0.8 and 1.0–2.4 ng/mL, respectively. The recoveries of the UV filters from the spiked water samples at the concentration of 100 ng/mL were 95.3–101.7%, with relative standard deviations <10%. Accordingly, the proposed portable device was demonstrated to be suitable for on‐site simultaneous sampling, purification, and preconcentration within a single step.     

Miniaturized molecularly imprinted polymer extraction method for the gas chromatographic analysis of flavonoids

In this study, the use of monolithic molecularly imprinted polymers in a micropipette tip format allowing the simple and fast extraction of flavonoids from standard solutions and a black tea sample is demonstrated. The imprinted polymer employed quercetin, methacrylic acid or 4‐vinylpyridine, and ethylene glycol dimethacrylate as template, functional monomer, and cross‐linker, respectively. Surface morphologies of the quercetin‐imprinted polymers and the corresponding nonimprinted polymers were characterized by SEM. Extraction of flavonoid standards was performed to evaluate the selectivity and recovery with these imprinted and nonimprinted polymers. Flavonoid compositions in aliquots eluted from the tips were identified using fast GC with flame ionization detection. Maximum specific capacities of 0.2, 5.7, and 16.0 mg/g for catechin, morin, and quercetin, respectively, were obtained with the imprinted polymer prepared with methacrylic acid, with the corresponding recoveries of 99.8, 98.8, and 95.4%, respectively. Efficient extraction by the quercetin‐imprinted polymer of epicatechin, catechin, and quercetin from an apple‐flavored black tea sample was achieved, with GC–MS employed for compound identification for both the tea and extracted samples.     

Photonic Floquet topological insulators in atomic ensembles

The feasibility of realizing a photonic Floquet topological insulator (PFTI) in an atomic ensemble is demonstrated. The interference of three coupling fields will split energy levels periodically, to form a periodic refractive index structure with honeycomb profile that can be adjusted by different frequency detunings and intensities of the coupling fields. This in turn will affect the appearance of Dirac cones in momentum space. When the honeycomb lattice sites are helically ordered along the propagation direction, gaps open at Dirac points, and one obtains a PFTI in an atomic vapor. An obliquely incident beam will be able to move along the zigzag edge of the lattice without scattering energy into the PFTI, due to the confinement of edge states. The appearance of Dirac cones and the formation of a photonic Floquet topological insulator can be shut down by the third‐order nonlinear susceptibility and opened up by the fifth‐order one.

     

Graphene screen‐printed radio‐frequency identification devices on flexible substrates

Despite the great promise of printed flexible electronics from 2D crystals, and especially graphene, few scalable applications have been reported so far that can be termed roll‐to‐roll compatible. Here we combine screen printed graphene with photonic annealing to realize radio‐frequency identification devices with a reading range of up to 4 meters. Most notably our approach leads to fatigue resistant devices showing less than 1% deterioration of electrical properties after 1000 bending cycles. The bending fatigue resistance demonstrated on a variety of technologically relevant plastic and paper substrates renders the material highly suitable for various printable wearable devices, where repeatable dynamic bending stress is expected during usage. All applied printing and post‐processing methods are compatible with roll‐to‐roll manufacturing and temperature sensitive flexible substrates providing a platform for the scalable manufacturing of mechanically stable and environmentally friendly graphene printed electronics.

     

Pulsed-field separation of particles in a microfluidic device

We demonstrate the proof-of-principle of a new separation concept for micrometer-sized particles in a structured microfluidic device. Under the action of externally applied, periodic voltage-pulses two different species of like-charged polystyrene beads are observed to simultaneously migrate into opposite directions. Based on a theoretical model of the particle motion in the microdevice that shows good agreement with the experimental measurements, the underlying separation mechanism is identified and explained. Potential biophysical applications, such as cell sorting, are briefly addressed.     

APU故障智能诊断系统设计

针对高旋环境下测试困难、测量精度低这一问题,提出了一种能在高旋环境下实现轴向减速装置,以达到稳定的良好的测试环境。该装置通过驱动仓内大量程陀螺仪测得的转速反馈给控制系统,控制系统输出控制信号来控制伺服电机,同时电机捷联内筒仓,使其相对外部转动方向反向旋转,实现轴向减速。实验结果表明,该装置可在高旋弹药飞行过程中提供稳定测试环境,从而得到更精准的姿态解算结果,为高旋环境下的测试提供了新的思路,具有广阔的应用前景。     

双原子正方晶格光子晶体边界模式的光传输特性

利用平面波展开法,发现双原子正方晶格光子晶体中ΓM方向边界面存在着快慢两类边界模式,并且通过计算色散关系和电场分布研究了边界参量对这两类边界模式传输特性的影响.依据两种模式的色散关系,计算了群指数和群速度色散参量,结果表明边界参量的变化对第一类边界模式传输特性的影响较小,该模式的平均群指数始终维持在5.0左右;第二类边界模式与第一类模式明显不同,边界参量的变化能够有效地影响到这种模式的传输特性,该模式的最大平均群指数可达178左右.利用时域有限差分法记录了不同时刻电场强度在边界附近的分布及监测点处的电场幅度变化情况,结果表明,两类模式都能够被限制在边界附近并向前传播,时域有限差分法得到的群速度与平面波展开法的结果完全吻合.     

Low power Electro-optical filter: Constructed using silicon nanobeam resonator and PIN junction

In this paper, a high tunable Electro-optical filter is designed and simulated with low electric power consumption. A silicon nanobeam resonator based on one-dimensional photonic crystal in the form of Fabry–Perot structure, silicon-on-insulator waveguide, is proposed with a PIN junction. In designing nanobeam resonator, “deterministic design method” is used to achieve the high quality factor and high-transmission rate. Tuning of the resonant wavelength in the output channel of the filter is achieved by manipulating the refractive index of the active area by using the free-carrier dispersion effect. The output wavelengths of designed device can be tuned for the telecom-friendly 1.55 µm range. The device shows a wavelength shift higher than 3 nm for a power consumption of only 0.9 mW. Finally, the simulation results show that the provided device can be considered as a narrowband and tunable Electro-optical filter that is suitable for DWDM communication system.     

A New Cells‐Compatible Microfluidic Device for Single Channel Recordings

We report the fabrication of a microfluidic apparatus and the realization of a sensors based on PEDOT : PSS, a biocompatible semiconductor polymer used in substitution of standard electrodes for electrophysiological studies and for detection of nanopores in membrane. This gives the possibility to study the mechanisms of ions balance and molecular transport though cell membranes. In particular the apparatus is based on two chambers connected through an aperture in a PTFE sheet where lipid bilayer are formed using Montal‐Mueller method, and the pore‐forming proteins activity is detected by polymeric electrodes. This methodology could be applied to examine different membrane proteins for the purpose of biosensing, drug screening and nanopore technologies.