Effect of wetting and drying on soil physical properties

Agricultural soils are subject to seasonal wetting and drying cycles. Effect of drying stress, as influenced by one cycle of wetting and drying, on physical properties of a clay–loam soil was investigated in the laboratory. The physical properties studied were soil bulk density, cone penetration resistance, shear strength, adhesion and aggregate size and stability. Three drying stress treatments were made by wetting air-dried soil of initial moisture content of 12% (on dry weight basis) to three different higher moisture contents, namely 27, 33 and 40%, and then drying each of them back to their original moisture content of 12%. Thus, the soil was subjected to three different degrees of drying stress. The results showed that the soil strength indicated by cone penetration resistance and cohesion, and soil aggregate size, increased with the degree of drying stress. However, the soil bulk density did not change significantly with the drying stress.     

数值建模时骨料对混凝土侵彻及毁伤问题的影响

采用二维拉格朗日弹塑性流体力学有限元程序LTZ-2D分析了含骨料混凝土的数值建模对混凝 土侵彻及毁伤问题的影响。对比等效混凝土,在混凝土骨料尺寸相对弹体尺寸较小的情况下,对于薄靶侵彻, 低速撞击时骨料对弹体有阻碍作用,而速度较高时,由于靶板背面毁伤面积增大的原因,弹体的剩余速度增 大;对于厚靶侵彻,含骨料混凝土的数值建模对弹体的侵彻过程影响不大。     

A3钢钝头弹撞击45钢板破坏模式的数值分析

不同速度范围内的A3钢钝头弹撞击45钢靶板分别表现为泰勒撞击、向日葵型花瓣帽形失效和靶板冲塞穿甲等3种不同的破坏模式,利用LS-DYNA对这种复杂的破坏机理和相应的影响因素进行了数值模拟研究。采用Johnson-Cook强度模型和累积损伤失效模型描述弹靶材料的力学性能,并考虑了塑性变形的绝热温升效应。数值模拟再现了不同破坏模式的失效过程,得到了与实验一致的结果。研究还指出,弹靶的冲塞穿甲实际是在高速撞击下,弹体发生花瓣帽形变形失效后继续穿甲靶板的后续结果。     

大长细比结构弹体侵彻2024-O铝靶的弹塑性动力响应

为研究大长细比结构弹体在撞击典型硬目标早期的结构动力学响应,利用57轻气炮进行了直径1.4 cm、量纲一壁厚0.1和0.15、长细比8和12、头部系数3和4.5的卵形空心弹体对2024-O铝靶的侵彻实验研究,利用高速摄影系统记录了弹体撞靶过程,观察到大长细比弹体垂直撞击硬目标过程中的局部墩粗、塑性屈曲2种结构破坏模式,以及斜侵彻过程中的整体塑性弯曲、弯曲与墩粗耦合、弯曲与屈曲耦合3种结构破坏模式和实时动力学响应过程。基于对指数硬化材料的空腔膨胀理论建立了弹体垂直侵彻模型,给出了在轴向及横向载荷交互作用下计算刚塑性自由梁危险截面屈服函数的控制方程,计算值与实验结果吻合较好。     

高温煅烧Mo改性的Fe／MgO催化剂用于制备管径分布均一的单壁碳纳米管

研究了在以甲烷化学气相沉积法制备单壁碳纳米管的过程中高温煅烧预处理(900℃煅烧10h)对Mo改性Fe/MgO催化剂的作用.发现这种预处理有利于Fe在催化剂中的稳定和分散,从而制备出管径均一的单壁碳纳米管.采用能谱元素分析、高分辨透射电镜、X射线衍射、比表面积测量、拉曼光谱和热重分析对样品进行了表征.结果表明,在碳纳米管生长的过程中,铁元素在催化剂表面富集,单壁碳纳米管生长于富集铁的纳米颗粒上,并存在碳管直径与铁颗粒尺寸的依赖关系.Mo存在时可煅烧形成FeMoO4复合氧化物,后者比MgFe2O4相更加稳定.Mo/Fe比例对提高单壁碳纳米管的生长密度、纯度与管径均一性等均有明显影响.上述研究对进一步精确控制制备单壁碳纳米管有重要意义.     

双层多孔介质燃烧器的数值模拟

考虑多孔固体构架的辐射换热以及气固相间的对流换热,引入弥散效应及相间对流换热系数,使用GRI3．0机理和双通量辐射模型,数值求解双层多孔介质内燃烧过程．分析了双层多孔介质燃烧器内火焰稳定性和污染物排放,并与单层的进行比较．结果表明,双层多孔介质燃烧器能够在较宽的流量范围内将火焰稳定在它的交界面附近．     

GPU-accelerated smoothed particle hydrodynamics modeling of jet formation and penetration capability of shaped charges

The prediction of the penetration of three-dimensional (3D) shaped charge into steel plates is a challenging task. In this paper, the smoothed particle hydrodynamics (SPH) method is applied to simulate the jet formation generated by the shaped charge detonation and its damage to steel plates. The Jones–Wilkins–Lee (JWL) equation of state (EOS), Tillotson EOS, and elastic–perfectly plastic constitutive model were incorporated into SPH for the modeling of explosive detonation and dynamic behavior of metal material. The compute unified device architecture (CUDA) parallel programming interface has been employed in SPH to improve the computational efficiency of SPH. Firstly, the constitutive models and EOSs are validated by 3D TNT slab detonation and aluminum–aluminum (Al–Al) high velocity impact. Then the jet formation of the shaped charge detonation and its penetration into the steel plates are investigated using the graphics processing unit (GPU)-accelerated SPH methodology. The numerical results of these test cases are compared against the published experimental data or analytical result, which shows that the GPU-accelerated SPH methodology is capable of tackling the 3D shaped charge detonation and penetration involving millions of particles with high computational efficiency.     

大锥角聚能射流实验研究

 通过闪光X射线摄影技术，研究了两种大锥角射流的特性及其对钢靶的侵彻，并与小锥角射流进行了对比。研究结果表明：大锥角射流的头部速度较低，但直径和质量较大，在大炸高条件下对钢靶的侵彻孔深度浅，孔径大。     

基于空耦超声的复合材料黏弹性评价方法*

复合材料的黏弹性是表征其内在阻尼机制的重要力学特性,而内在阻尼机制是材料安全性能的一个重要评价指标。该文提出了空气耦合超声波的材料黏弹性评价方法。首先讨论了黏弹性进行评价的相关理论,利用接触式超声波底面回波法与空气耦合超声波透射法对比验证,其结果基本一致,证明了空气耦合超声对材料黏弹性检测的有效性。并且对一批不同铺层方向的碳纤维复合材料进行了评价,其结果与期望值完全相符,验证了该方法的可行性和准确性,为复合材料的动态力学特性评价和安全评价提供了新的思路。     

劈尖干涉测量细丝直径新法

劈尖干涉测量细丝直径,通常涉及到测量交线至细丝的距离L。而在实验中,由于劈尖两端被夹座掩盖,无法准确测量出L的长度,进而影响到直径的准确度。采用移位法进行二次测量,既能准确方便的测量出细丝直径,又避开了测量L。