Hydrogen analysis in solid samples by utilizing He metastable atoms induced by TEA CO2 laser plasma in He gas at 1 atm

A TEA CO₂ laser (350 mJ–1.5 J, 10.6 μm, 200 ns, 10 Hz) was focused onto a metal sub-target under He as host gas at 1 atmospheric pressure with a small amount of impurity gas, such as water and ethanol vapors. It was found that the TEA CO₂ laser with the help of the metal sub-target is favorable for generating a strong, large volume helium gas breakdown plasma at 1 atmospheric pressure, in which the helium metastable-excited state was then produced overwhelmingly. While the metal sub-target itself was never ablated. The helium metastable-excited state produced after the strong helium gas breakdown plasma was considered to play an important role in exciting the atoms. This was confirmed by the specific characteristics of the detected H emission, namely the strong intensity with low background, narrow spectral width, and the long lifetime. This technique can be used for gas and solid samples analysis. For nonmetal solid analysis, a metal mesh was introduced in front of the nonmetal sample surface to help initiation of the helium gas breakdown plasma. For metal sample, analysis can be carried out by combining the TEA CO₂ laser and an Nd–YAG laser where the Nd–YAG laser is used to ablate the metal sample. The ablated atoms from the metal sample are then sent into the region of helium gas breakdown plasma induced by the TEA CO₂ laser to be excited through the helium metastable-excited state. This technique can be extended to the analysis of other elements, not limited only to hydrogen, such as halogens.     

Positive ion chemistry of esters of carboxylic acids in air plasma at atmospheric pressure

Ionization of esters of carboxylic acids RCOOR' (R = H, alkyl; R' = alkyl) within the air plasma of the Atmospheric Pressure Chemical Ionization (APCI) source occurs largely via H(+)-transfer and, to a minor extent, via NO(+) association. The protonated ester MH(+) is normally observed as M(2)H(+) and as higher aggregates (M(3)H(+), M(3)H(+)(H(2)O)) also at high source temperature. The behavior of M(2)H(+) upon collisional activation is consistent with the reported dissociation of proton-bound dimers to MH(+) species that, in turn, fragment according to the known paths of lowest energy. In addition, other important product ions form within the plasma, some in very high relative abundance, which are attributed to ion-molecule condensation reactions between neutral M and either MH(+) or M(2)H(+) resulting in the elimination of CO, R'OH, alkene from the alkoxy moiety of the ester and HCOOH. A general scheme is proposed to account for the experimental observations, which suggest that the encounter complex formed between MH(+) and M or between M(2)H(+) and M may either collisionally relax to the protonated dimer or trimer, respectively, or react via covalent bond forming and cleaving steps to eliminate stable neutral molecules. The proposed scheme is supported by both the observed concentration dependence and the temperature dependence of the products relative abundances within the plasma. Such reactions can be the dominant process, as in the case of formate esters. A second significant ionization route involves addition of NO(+) to form M(n)NO(+) (n = 1, 2, 3). An additional product corresponding to [M(2)NO(+) - CO(2)] is also observed with iso- and n-butyl formate esters.     

Parametric study of the flow and temperature fields in an inductively coupled r.f. plasma torch

A theoretical investigation of the effect of different parameters on the flow and the temperature fields in a radiofrequency inductively coupled plasma is carried out. The parameters studied are: central injection gas flow rate, total gas flow rate, input power, and the type of plasma gas. The results obtained for argon and nitrogen plasmas at atmospheric pressure indicate that the flow and the temperature fields in the coil region, as well as the heat flux to the wall of the plasma confinement tube, are considerably altered by the changes in the torch operating conditions.     

The use of carbon nanofibers microcolumn preconcentration for inductively coupled plasma mass spectrometry determination of Mn,Co and Ni

Based on carbon nanofibers (CNFs) as a solid phase extraction adsorbent, a microcolumn preconcentration method coupled to inductively coupled plasma mass spectrometry (ICP–MS) was developed for the determination of trace elements (Mn, Co and Ni). The effect of various experimental parameters such as pH, sample flow rate and volume, elution solution and interfering ions on the retention of the studied ions have been investigated systematically. During all the steps of the experimental process, Mn, Co and Ni could be quantitatively sorbed on the microcolumn containing CNFs in the range of pH 6.0–9.0, and then eluted completely with 0.5 mol ml^− 1 HNO₃. A preconcentration factor of 150-fold was obtained. The detection limits for Mn, Co and Ni were 40, 0.4 and 8.0 pg ml^− 1, respectively, with relative standard deviations less than 6.0%. In order to validate the proposed method, two certified reference materials of human hair (GBW 07601) and mussel (GBW 08571), and water sample were analyzed with satisfactory results. The recoveries were between 95.0 and 114%.     

Optical emission spectroscopy as a real time diagnostic tool for plasma-assisted deposition of TiN

Real-time optical emission spectroscopy (OES) was used to monitor the deposition of TiN both from mixtures of tetrakis(dimethylamino)titanium (TDMATi)-N₂ and TiCl₄-H₂-N₂ in an electron cyclotron resonance chemical vapor deposition system. The accurate control of the ratio of the emission intensities of ionized nitrogen at 391.4 nm and molecular nitrogen at 357.7 nm (N ₂ ⁺ /N₂) led to low temperature deposition of stoichiometric TiN (Ti/N ≈ 1) and very low resistivity in both cases. It was found that high ion density plasmas are crucial for a considerable reduction of the deposition temperature while maintaining good film quality. OES shows that the abundance of certain excited plasma species is not only dependent on the gas mixture and the deposition parameters, such as total pressure and microwave power, but also is strongly affected by the magnetic field configuration. The deposition rate and the film resistivity can be related to the emission intensity ratio, I(N ₂ ⁺ )/I(N₂). Finally, the two processes are compared in terms of the quality of as-deposited and heat-treated films. The comparison shows that the films obtained with TDMATi exhibit lower resistivity and are thermally more stable than with TiCl₄.     

Air microwave-induced plasma: Relation between ion density and atomic oxygen density

Electron temperature and ion density are measured in an air microwave-induced plasma (2450 MHz) by means of a floating double probe. A 'cinetic scheme for ion formation and decay is set up, and a relationship between atomic oxygen and ion densities is obtained. From this relationship an order-of-magnitude of atomic oxygen concentration in the discharge is derived and compared with results obtained by optical actinometry in another work.     

甲烷二氧化碳介质阻挡放电转化产物分布研究

针对介质阻挡放电甲烷二氧化碳转化实验,分析了反应的产物分布,探讨了进料组成和反应器结构对反应的影响.反应产物包括:高H2/CO摩尔比的合成气、气态烃、高辛烷值的汽油组分、醇和酸等含氧有机物.对所述电极结构,产物的选择性随碳数增加而降低;高的甲烷进料浓度有利于烃的生成,对醇和酸的最佳甲烷进料体积分数范围在67.4％～75.1％;放电间隙越小,原料转化率和烃、酸的选择性越大,大的放电间隙对醇的生成有利.     

Influence of velocity and surface temperature of alumina particles on the properties of plasma sprayed coatings

In this paper are described the main characteristics of the plasma spraying process of alumina deposits, i.e., the temperature and flow field of the plasma jets obtained with the classical spraying torches, the injection of the particles into the plasma jet, the particle surface temperature and velocities in the plasma (measured for calibrated alumina particles), and the coating generation. The measurements on the alumina particles are compared with the predictions of a mathematical model. The experimental and computed particle velocities are in rather good agreement. However, this is not the case for the particle surface temperature. Possible reasons for the discrepancy are proposed (influence of the carrier gas, thermophoretic forces, and poor penetration of the particles into the plasma core even for an injection velocity twice that of the optimal calculated one, as shown by recent measurements). Finally the correlations between the particle velocities and surface temperature, and the properties of the alumina coating (porosity, crystal structure, mechanical properties) are studied.     

Transport efficiency in femtosecond laser ablation inductively coupled plasma mass spectrometry applying ablation cells with short and long washout times

Relative mass transport efficiencies of near infrared (λ = 795 nm) femtosecond laser generated brass aerosols in helium were measured by ICP-MS applying different ablation cells with short and long washout times. It was found that the transport efficiencies are independent of the cell used within the mutual experimental uncertainties. This finding was confirmed by additional measurements providing the absolute particle mass transport efficiencies of femtosecond laser ablation in He. Here, the transport efficiencies were determined by weighing the samples before and after ablation with a micro-balance, collecting the particles by low-pressure impaction, and evaluating the impacted masses quantitatively by total reflection X-ray fluorescence. Within the experimental uncertainties (± 9–19%) the same absolute transport efficiency (about 77%) was found for all cells applied. This efficiency value can be regarded as a lower limit of the absolute mass transport efficiency since mass losses in the impactor are difficult to quantify.     

INTROMISSION OF WATER-REPELLENT AND HYDROSCOPIC PROPERTIES SIMULTANEOUSLY TO PP BY PLASMA DISCHARGE METHOD

Plasma-induced surface graft copolymerization of acrylic acid on polypropylene non-woven fabric (PP-g-AA) and polypropylene membrane were reported. The extents of grafting were controlled by the plasma and polymerization condition. Hexadecyltrimethyl ammonium bromide was then coupled with the carboxyl group of PP-g-AA to obtain a polyion complex (PIC). At last, CF4 plasma was used to give PICs hydrophobic property. The moisture regain and water-repellency of the processed PICs was investigated. The surfaces were characterized using ATR FT-IR and XPS. The result indicates that the products have very high ability to adsorb moisture, even better than cotton fiber. At the same time, the products show excellent hydrophobic property, which can‘t be wetted by those reagents whose surface tensions were higher than 327mN/m.