Iron-Cobalt-Silica Aerogel Nanocomposite Materials

Iron-Cobalt-Silica nanocomposites were prepared in form of aerogels. X-ray diffraction, transmission electron microscopy and N₂ physisorption at 77 K were used to investigate the structure, size and dispersion of the nanocrystals and the porous structure in the aerogels and in the final composites. The variation of the supercritical drying conditions gives rise to differences in the morphological features of the aerogels. These differences influence the size of the cobalt oxide nanoparticles in the aerogels. On the other hand, after the reduction treatment the average size of the alloy nanoparticles is the same in all the aerogel nanocomposites. The effect of reduction temperature on alloy formation and particle size is also discussed.     

Thermal evolution of ferromagnetic metallic glasses

A traditional TG apparatus was modified by placing two permanent magnets producing a controlled magnetic field (TG(M): Magneto Thermogravimetry). This technique proved to be useful to study both structural relaxation and crystallisation of ferromagnetic metallic glasses. Results obtained for the amorphous alloys Fe₄₀Ni₄₀P₁₄B₆ and Fe_62.5Co₆Ni_7.5Zr₆Nb₂Cu₁B₁₅, are reported in this paper. Structural relaxation can be evaluated by measuring changes in Curie temperature induced by thermal treatments. Crystallisation in TG(M) is detected through a change in the measured apparent mass (difference between the sample mass and magnetic force driving it upward). These results were confirmed by DSC analysis. Whether the obtained crystalline phase is ferromagnetic, it can be identified through its Curie temperature, measured by TG(M). In fact the value of 770°C measured as Curie temperature of crystallised Fe_62.5Co₆Ni_7.5Zr₆Nb₂Cu₁B₁₅led to conclude that the only ferromagnetic crystalline phase is a-Fe. These hypothesis was confirmed by XRD analysis, showing that the first crystallisation yields to a-Fe nanocrystals. This revised version was published online in July 2006 with corrections to the Cover Date.     

AuPt Bipyramid Nanoframes as Multifunctional Platforms for In Situ Monitoring of the Reduction of Nitrobenzene and Enhanced Electrocatalytic Methanol Oxidation

Multifunctional metal nanostructures with a hollow feature, especially for nanoframes, are highly attractive owing to their high surface-to-volume ratios. However, pre-grown metal nanocrystals are always involved during the preparation procedure, and a synthetic strategy without the use of a pre-grown template is still a challenge. In this article, a template-free strategy is reported for the preparation of novel AuPt alloy nanoframes through simply mixing HAuCl₄ and H₂PtCl₆ under mild conditions. The alloy nanostructures show a bipyramid-frame hollow architecture with the existence of only the ten ridges and absence of their side faces. This is the first report of bipyramid-like nanoframes and a template-free method under mild conditions. This configuration merges the plasmonic features of Au and highly active catalytic sites of Pt in a single nanostructure, making it an ideal multifunctional platform for catalyzing and monitoring the catalytic reaction in real time. The superior catalytic activity is demonstrated by using the reduction of nitrobenzene to the corresponding aminobenzene as a model reaction. More importantly, the AuPt nanoframes can track the reduction process on the basis of the SERS signals of the reactants, intermediates, and products, which helps to reveal the reaction mechanism. In addition, the AuPt nanoframes show much higher electrocatalytic properties toward the methanol oxidation reaction than commercial Pt/C electrocatalysts.     

Cathodic deposition of ternary In+As+Sb alloys and formation of InAsxSb1−x

In+As+Sb alloys have been deposited onto Ni and Ti cathodes from tartaric acid solutions at pH 2. Homogeneous deposits of composition suitable for achieving InAs_xSb_1−x can be obtained from this medium. The As-to-Sb ratio can be controlled by properly selecting solution composition and deposition potential.X-ray photoelectron spectroscopy and X-ray diffraction analyses show that formation of III–V compounds occurs at room temperature. In reacts preferentially with As rather than with Sb, but crystalline phases formed at room temperature are Sb-rich. After annealing the In+As+Sb alloys at 250°C, the composition calculated from cell parameters appears similar to that measured by energy-dispersive X-ray analysis, suggesting that the entire deposit has been converted into the InAs_xSb_1−x crystalline phase.     

Spectrophotometric determination of zinc in copper-base alloys with TAN

TAN reacts with zinc(II) forming a red complex with composition 1:2 Zn(II)-TAN and absorption maximum at 582 nm. Zinc can be determined with this reagent in the presence of Triton X-100, in the pH range 6.20-8.00 with a molar absorptivity of 4.5×10⁴ l/mol/cm Beer's Law was obeyed up to least 1.55 g/ml. Copper interference was eliminated with a mixture of thiosulfate and ascorbic acid and nickel separated by precipitation with dimethylglyoxime. The proposed method was used for zinc determination in several copper-base alloys and the results of analysis in comparison with certified values indicated that the procedure was accurate and precise. A derivative procedure is also proposed, allowing zinc determination with high sensitivity (5-400 ng/ml).     

反相流动注射催化光度法测定痕量锰

本文基于在邻菲罗啉活化下，锰（Ⅱ）对高碘酸钾氧化罗丹明Ｂ褪色的催化作用，建立了痕量锰的反相流动注射分析方法。方法的线性范围为０－５０μｇ／Ｌ，检测下限为０．７μｇ／Ｌ锰（Ⅱ）。对２０μｇ／Ｌ锰（Ⅱ）测定九次的相对标准偏差为１．８％，进样频率不少于６０次／ｈ。方法应用于水样和标准镁合金样品分析，结果满意。     

Pulse plating effect on microstructure and corrosion properties of Zn–Ni alloy coatings

The influence of pulse plating parameters on the surface morphology, grain size, lattice imperfection and corrosion properties of Zn–Ni alloy has been studied. The coatings were electrodeposited in an alkaline cyanide-free solution. AFM was applied for surface morphology examination, XRD measurements were carried out for phase composition and texture analysis, electron probe microanalysis was used for alloy chemical composition studies, while electrochemical techniques were applied for corrosion performance evaluation. The pulse plated Zn–Ni coatings appeared to consist of the γ-Zn₂₁Ni₅ phase and the composition of the alloy depended on the plating parameters. The grain size, lattice imperfection and homogeneity of grain distribution were established to be the main factors determining corrosion behaviour of the coating. Presented at the 4th Baltic Conference on Electrochemistry, Greifswald, March 13–16, 2005     

Electroreduction of α-glucose on CNT/graphite electrode modified by Zn and Zn–Fe alloy

Electroreduction of -glucose to form sorbitol on Zn/CNTs and Zn alloy/CNTs electrodes has been investigated in this paper. Carbon nanotubes (CNTs) used in this paper are grown directly on graphite disks by chemical vapor deposition. Zn and Zn alloy are electrodeposited on the activated CNTs/graphite electrode by pulse galvanostatic method. The micrographs of Zn/CNTs and Zn alloy/CNTs electrodes are characterized by scanning electron microscopy. The results show that the current efficiency of -glucose reduction on CNTs electrodes is much better than that on flat Zn electrodes. The order of the current efficiency on different electrodes is as follows: Zn/CNT (0.58) Zn–Fe/CNT (0.57)>Zn–Ni/CNT (0.43) Zn/graphite (0.42)>Zn (0.40). It indicates that CNTs have good potential application in electrosynthesis. Additionally, effects of some operating parameters, such as pH, temperature and -glucose concentration, on the current efficiency of -glucose reduction are also discussed.     

Tuning Nanoparticle Catalysis for the Oxygen Reduction Reaction

Advances in chemical syntheses have led to the formation of various kinds of nanoparticles (NPs) with more rational control of size, shape, composition, structure and catalysis. This review highlights recent efforts in the development of Pt and non‐Pt based NPs into advanced nanocatalysts for efficient oxygen reduction reaction (ORR) under fuel‐cell reaction conditions. It first outlines the shape controlled synthesis of Pt NPs and their shape‐dependent ORR. Then it summarizes the studies of alloy and core–shell NPs with controlled electronic (alloying) and strain (geometric) effects for tuning ORR catalysis. It further provides a brief overview of ORR catalytic enhancement with Pt‐based NPs supported on graphene and coated with an ionic liquid. The review finally introduces some non‐Pt NPs as a new generation of catalysts for ORR. The reported new syntheses with NP parameter‐tuning capability should pave the way for future development of highly efficient catalysts for applications in fuel cells, metal‐air batteries, and even in other important chemical reactions.     

Hydrogen in Palladium and Storage Properties of Related Nanomaterials: Size,Shape, Alloying,and Metal-Organic Framework Coating Effects

One of the key issues for an upcoming hydrogen energy-based society is to develop highly efficient hydrogen-storage materials. Among the many hydrogen-storage materials reported, transition-metal hydrides can reversibly absorb and desorb hydrogen, and have thus attracted much interest from fundamental science to applications. In particular, the Pd−H system is a simple and classical metal-hydrogen system, providing a platform suitable for a thorough understanding of ways of controlling the hydrogen-storage properties of materials. By contrast, metal nanoparticles have been recently studied for hydrogen storage because of their unique properties and the degrees of freedom which cannot be observed in bulk, i. e., the size, shape, alloying, and surface coating. In this review, we overview the effects of such degrees of freedom on the hydrogen-storage properties of Pd-related nanomaterials, based on the fundamental science of bulk Pd−H. We shall show that sufficiently understanding the nature of the interaction between hydrogen and host materials enables us to control the hydrogen-storage properties though the electronic-structure control of materials.