强激光反射镜基体材料的热畸变特性有限元分析

利用有限元方法数值模拟了单晶硅（Si）、铜（Cu）、钨(W)、氧化铍(BeO)等镜体材料的热畸变特性。结果表明：当入射激光功率为2 kW、镜面反射率为93%、光斑直径为17 mm、激光照射时间为10 s时,四种材料基板的中心最大热变形分别为0.984,3.32,1.55,1.88 μm。相比之下,Si镜的热变形最小,是比较理想的镜体材料;Cu镜的热变形最大;W和BeO两种材料的镜热变形介于Si镜和Cu镜之间,具有较高的强度和硬度,抗破坏能力较强。     

Thermally crosslinkable hole‐transporting poly(fluorene‐co‐triphenylamine) for multilayer polymer light‐emitting diodes

This article reports the synthesis and characterization of a novel thermally crosslinkable hole‐transporting poly (fluorene‐co‐triphenylamine) (PFO‐TPA) by Suzuki coupling reaction, followed with its application in the fabrication of multilayer light‐emitting diodes by wet processes. The thermal, photophysical, and electrochemical properties of PFO‐TPA were investigated by differential scanning calorimeter, thermogravimetric analysis, optical spectroscopy, and cyclic voltammetry, respectively. Thermally crosslinked PFO‐TPA, through pendant styryl groups, demonstrates excellent thermal stability (T_d > 400 °C, T_g = 152 °C), solvent resistance, and film homogeneity. Its highest occupied molecular orbital level (?5.30 eV) lies between those of PEDOT:PSS (?5.0 ～ ?5.2 eV) and poly(9,9‐dioctylfluorene) (PFO: ?5.70 eV), forming a stepwise energy ladder to facilitate hole injection. Multilayer device with crosslinked PFO‐TPA as hole‐injection layer (HIL) (ITO/PEDOT:PSS/HIL/PFO/LiF/Ca/Al) was readily fabricated by successive spin‐coating processes, its maximum luminance efficiency (3.16 cd/A) were about six times higher than those without PFO‐TPA layer (0.50 cd/A). The result of hole‐only device also confirmed hole‐injection and hole‐transport abilities of crosslinked PFO‐TPA layer. Consequently, the device performance enhancement is attributed to more balanced charges injection in the presence of crosslinked PFO‐TPA layer. The thermally crosslinkable PFO‐TPA is a promising material for the fabrication of efficient multilayer polymer light‐emitting diodes because it is not only a hole‐transporting polymer but also thermally crosslinkable. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Fabrication of a covalently attached multilayer film electrode containing cobalt phthalocyanine and its application as a potentiometric sensor of iodide ion

Construction of a highly stable covalently attached multilayer film electrode containing cobalt phthalocyanine was achieved by UV irradiation of ionic self-assembled multilayer films of diazo-resins (DAR) and cobalt phthalocyanine tetrasulfonic acid (CoTsPc) tetrasodium salt. The modified electrode had good potentiometric response to iodide ion. The potentiometric response was independent of the pH of the solution between pH 2.5 and 6.0, while it was dependent on the nature of the buffer media. The modified electrode had a linear dynamic range between 4.7×10⁻⁶ M and 0.1 M with a Nernstian slope of 58.8 mV per decade and a detection limit of 3.5×10⁻⁶ M in acetate buffer (0.1 M, pH 4.6). The modified electrode also exhibited a fast response, good stability and repeatability.     

Achiral and chiral separations using MEKC,polyelectrolyte multilayer coatings,and mixed mode separation techniques with molecular micelles

Mixed mode (MM) separation using a combination of MEKC and polyelectrolyte multilayer (PEM) coatings is herein reported for the separation of achiral and chiral analytes. Many analytes are difficult to separate by MEKC and PEM coatings alone. Therefore, the implementation of a MM separation provides several advantages for overcoming the limitations of these well‐established methods. In this study, it was observed that achiral separations using MEKC and PEM coatings individually resulted in partial resolution of eight very similar aryl ketones when the molecular micelle (sodium poly(N‐undecanoyl‐L ‐glycinate)) concentration was varied from 0.25 to 1.00% w/v and the bilayer number varied from 2 to 4. However, when MM separation was introduced, baseline resolution was achieved for all eight analytes. In the case of chiral separations, temazepam, aminoglutethimide, benzoin, benzoin methyl ether, and coumachlor were separated using the three separation techniques. For chiral separations, the chiral molecular micelle, sodium poly(N‐undecanoyl‐L ‐leucylvalinate), was employed at concentrations of 0.25–1.50% w/v for both MEKC and PEM coatings. Overall, the results revealed partial separation with MEKC and PEM coatings individually. However, MM separation enabled baseline separation of each chiral mixture. The separation of achiral and chiral compounds from different compound classes demonstrates the versatility of this MM approach.     

Multilayer dielectric cylindrical mirrors based on omnidirectional reflection from a one-dimensional photonic crystal

A multilayer dielectric cylindrical mirror (MDCM) based on the one-dimensional omnidirectional reflection of a photonic crystal is presented. In this case, the refractive indices of the two materials are 1.6 (polystyrene) and 4.6 (tellurium), and the corresponding optimized thicknesses are 0.75a and 0.25a. A very high reflectance over a wide frequency range is observed. In this case, a is the lattice constant of the photonic crystal. In this band, the MDCM has good reflection and focal properties. Therefore, it is feasible to use the MDCM for integrated waveguide devices. As an example, an etched diffraction grating demultiplexer based on the MDCM is also proposed. Both the operational principle and design of the device are introduced. This provides a method for designing compact integrated waveguide devices.     

Design of different bandwidth dispersive mirrors

Dispersive mirrors in the wavelength range of 960–1110 nm, 700–900 nm, 950–1150 nm, 600–900 nm, 900–1200 nm, 600–1000 nm and 550–1050 nm are designed, respectively. From the design results, we analyse the choice of material and the approach to dispersion compensation. Furthermore, along with the increase of bandwidth, interaction between group delay dispersion (GDD) oscillation and high reflectivity, and influence of bandwidth on both GDD ripple and reflectivity are discussed.     

High efficiency top-emitting white organic light-emitting devices with a (metal/organic)2 cathode

White top-emitting organic light-emitting devices (TEOLEDs) were fabricated on a glass substrate with metal/organic multilayer of (Ag/Alq₃)₂ (Alq₃ is tris-(8-hydroxyquinoline) aluminum) as cathode. White TEOLEDs with high efficiency were obtained due to the microcavity effects. And the (Ag/Alq₃)₂ cathode, which adjusted the optical characteristics of the devices, played an important role. In addition, Alq₃–Ag–Alq₃ multilayer could work as a buffer layer, which would simplify the process of encapsulation for devices. We also calculated the electroluminescence spectrum of devices encapsulated with Al₂O₃ (150 nm) and Al₂O₃(75 nm)/ZrO₂(75 nm). And the results indicated that the CIE coordinates is almost the same between with and without encapsulating.     

Electric field-induced stress birefringence in layered composites PbZr1-xTixO3/Polycarbonate

Electro-optical composites based on the product of electro-strictive and elasto-optical effects are developed.Layered composites of PbZr 1 x Ti x O 3 and polycarbonate are synthesised.Their electro-optical properties are studied.The nominal transverse electro-optical coefficient of the composite is observed to be about 3.6 times larger than that of LiNbO 3.Experiments and theoretical analyses show that the electro-optical effect of the composite has a strong ’size effect’.With the ratio of thickness/length decreasing or the width of elasto-optical phase increasing,the half-wave electric field intensity increases but the transverse electro-optical coefficient decreases for the layered composite.     

Synchrotron X‐ray tests of an L‐shaped laterally graded multilayer mirror for the analyzer system of the ultra‐high‐resolution IXS spectrometer at NSLS‐II

Characterization and testing of an L‐shaped laterally graded multilayer mirror are presented. This mirror is designed as a two‐dimensional collimating optics for the analyzer system of the ultra‐high‐resolution inelastic X‐ray scattering (IXS) spectrometer at National Synchrotron Light Source II (NSLS‐II). The characterization includes point‐to‐point reflectivity measurements, lattice parameter determination and mirror metrology (figure, slope error and roughness). The synchrotron X‐ray test of the mirror was carried out reversely as a focusing device. The results show that the L‐shaped laterally graded multilayer mirror is suitable to be used, with high efficiency, for the analyzer system of the IXS spectrometer at NSLS‐II.