Optical design of bent rib waveguide with MOS cross-section

We provided a single-mode bent MOS-cross-section rib waveguide design with 0.9 dB/cm bending loss at 25 μm bending radius. The peak position for the TE-like mode was tuned to the gate oxide around which the maximum amount of free carriers are accumulated to optimize the free carrier dispersion effect.     

光子晶体波导定向耦合型1×3光分束器

将五光子晶体单模波导平行、邻近放置构成定向耦合器,依据自映像原理,数值分析了输入光场对称入射时,该系统中光的传播行为.基于此结构,设计了1×3光分束器,其器件长度可短至14.26μm.仅仅通过对称地改变耦合区中两个介质柱的有效折射率,使光场在横向发生重新分布,便可实现输出能量的均分或自由分配.通过非对称地改变耦合区中的一个介质柱,可实现3个输出端的输出能量的自由分配.该光分束器具有微小尺寸和各输出端输出能量的比例可自由调制的特点,在未来集成光回路中具有广泛的应用价值.     

波导侧壁起伏对聚酰亚胺波导光学梳状滤波器串扰特性的影响及其改善方法

提出了一种结构模型来分析由工艺引起的波导侧壁起伏对于聚合物波导光学梳状滤波器的滤波特性的影响。含氟聚酰亚胺高分子聚合物制备多级马赫一曾德尔串联型光学梳状滤波器件的工作参量为中心波长1550nm,波长间隔为0．8nm,40通道的波长交错分离。模拟计算：表明,对由高分子聚合物材料制备的多级马赫-曾德尔串联型光学梳状滤波器件,其主要影响是增大了信道之间的串扰,中心波长1550nm处的信道串扰由理想情况下的-40dB降为-12dB,极大地影响了器件的性能。在此基础上,提出一种改善光学梳状滤波器串扰性能的新结构,该结构由多级马赫-曾德尔耦合器和微环共振滤波器串接构成,40个通道的串扰改善为-0dB以下。     

平面光波导器件时域有限差分束传输法分析中边界和初始条件的处理

从慢变包络（SVEA）时域光传输方程出发,对比了综合道格拉斯（GD）和传统的中心差分（CN）两种离散化格式,指出GD法比CN法精度有了很大提高.重点讨论了GD法的TD-BPM边界处理问题,给出了吸收边界和透明边界离散的显式和隐式表达式,分析并确定了交替方向隐式法（ADIM）的边界处理方式;同时,对激励源加入的连接边界进行了仔细讨论.结果表明对于隐式GD-TD-BPM法边界处理应采用隐式,中间激励更能反映光波导反射场的情况.     

Hard X-ray micro-spectroscopy at Berliner Elektronenspeicherring für Synchrotronstrahlung II

The capabilities of the X-ray beamlines at Berliner Elektronenspeicherring für Synchrotronstrahlung II (BESSY II) for hard X-ray measurements with micro- and nanometer spatial resolution are reviewed. The micro-X-ray fluorescence analysis (micro-XRF), micro-extended X-ray absorption fine structure (micro-EXAFS), micro-X-ray absorption near-edge structure (micro-XANES) as well as X-ray standing wave technique (XSW), X-ray beam induced current (XBIC) in combination with micro-XRF and micro-diffraction as powerful methods for organic and inorganic sample characterization with synchrotron radiation are discussed. Mono and polycapillary optical systems were used for fine X-ray focusing down to 1 µm spot size with monochromatic and white synchrotron radiation. Polycapillary based confocal detection was applied for depth-resolved micro-XRF analysis with a volume resolution down to 3.4 · 10^− 6 mm³. Standing wave excitation in waveguides was also applied to nano-EXAFS measurements with depth resolution on the order of 1 nm. Several examples of the methods and its applications in material research, biological investigations and metal-semiconductor interfaces analysis are given.     

Optical sensing in microfluidic lab-on-a-chip by femtosecond-laser-written waveguides

We use direct femtosecond laser writing to integrate optical waveguides into a commercial fused silica capillary electrophoresis chip. High-quality waveguides crossing the microfluidic channels are fabricated and used to optically address, with high spatial selectivity, their content. Fluorescence from the optically excited volume is efficiently collected at a 90° angle by a high numerical aperture fiber, resulting in a highly compact and portable device. To test the platform we performed electrophoresis and detection of a 23-mer oligonucleotide plug. Our approach is quite powerful because it allows the integration of photonic functionalities, by simple post-processing, into commercial LOCs fabricated with standard techniques. Figure Femtosecond laser written waveguides can selectively excite fluorescence in a microfluidic channel of a commercial lab-on-a-chip. A compact scheme for on-chip detection by laser induced fluorescence is applied to capillary electrophoresis of a 23-mer Cy3-labeled oligonucleotide     

Optimization of highly nonlinear dispersion-flattened photonic crystal fiber for supercontinuum generation

A simple type of photonic crystal fiber (PCF) for supercontinuum generation is proposed for the first time. The proposed PCF is composed of a solid silica core and a cladding with square lattice uniform elliptical air holes, which offers not only a large nonlinear coefficient but also a high birefringence and low leakage losses. The PCF with nonlinear coefficient as large as 46 W 1 · km-1 at the wavelength of 1.55 μm and a total dispersion as low as ±2.5 ps · nm-1 · km-1 over an ultra-broad waveband range of the S-C-L band (wavelength from 1.46 μm to 1.625 μm) is optimized by adjusting its structure parameter, such as the lattice constant Λ , the air-filling fraction f , and the air-hole ellipticity η. The novel PCF with ultra-flattened dispersion, highly nonlinear coefficient, and nearly zero negative dispersion slope will offer a possibility of efficient super-continuum generation in telecommunication windows using a few ps pulses.     

All polymer asymmetric Mach-Zehnder interferometer waveguide sensor by imprinting bonding and laser polishing

We present an all polymer asymmetric Mach–Zehnder interferometer(AMZI) waveguide sensor based on imprinting bonding and laser polishing method. The fabrication methods are compatible with high accuracy waveguide sensing structure. The rectangle waveguide structure of this sensor has three sensing surfaces contacting the test media, and its sensing accuracy can be increased 5 times compared with that of one surface sensing structure. An AMZI device structure is designed. The single mode condition, the length of the sensing arm, and the length deviation between the sensing arm and the reference arm are optimized. The length deviation is optimized to be 19.8 μm in a refractive index range between1.470 and 1.545. We fabricate the AMZI waveguide by lithography and wet etching method. The imprinting bonding and laser polishing method is proposed and investigated. The insertion loss is between-80.36 dB and-10.63 dB. The average and linear sensitivity are 768.1 d B/RIU and 548.95 dB/RIU, respectively. And the average and linear detection resolution of the sensor are 1.30×10~(-6) RIU(RIU: refractive index unit) and 1.82×10~(-5) RIU, respectively. This sensor has a fast and cost-effective fabrication process which can be used in the cases of requiring portability and disposability.     

Mode theory of three-layer cylindrical waveguides and its application to aurum(Au)/polystyrene(PS)-coated terahertz hollow waveguides

In this paper, we present a generic mode theory for the three-layer cylindrical waveguides consisting of three arbitrary material mediums. Based on derived eigenvalue equations of the TE, TM, and hybrid modes, the mode conditions of metal/dielectric-coated terahertz hollow waveguides are extracted. In addition, we quantitatively describe both the effective refractive indexes and the loss characteristics of the aurum/polystyrene-coated terahertz hollow waveguides operating at the TE₀₁, TM₀₁, and HE₁₁ modes. It is indicated that the loss coefficient of the TE₀₁ mode can be much lower than that of the TM₀₁, and HE₁₁ modes, and, especially, can tend to that of the terahertz wave in air. So the TE₀₁ mode is very significant for the hollow waveguides in term of low loss propagating of the terahertz wave. We expect these results to enable a variety of new long-distance THz applications in sensing, detecting and communicating.     

F8BT：P3HT共混薄膜的放大自发辐射

研究了聚合物poly（9,9-dioctylfluorene-co-benzothiadiazole）（F8BT）和poly （3-hexylthiophene）（P3HT）共混薄膜的放大自发辐射（ASE）现象,对影响其阈值的两个因素--增益和损耗进行了详细的研究。结果显示,共混聚合物的发光效率随着P3HT所占比例的增加有所降低。当P3HT比例低于20%时,发光效率降低不多,而其损耗则随着P3HT的增加显著减小。F8BT和P3HT混合后,光损耗系数从7.8 cm^-1下降到4 cm^-1左右。这表明F8BT：P3HT共混聚合物光波导的ASE阈值降低主要是由于其损耗的降低而导致的。ASE阈值的降低预示该材料体系容易实现电泵浦激光。