Physical properties of glycosaminoglycan hydrogels

The chemical composition of glycosaminoglycan (GAG) hydrogels was found to have a profound effect on the physical properties of gels. Hyaluronan (HA) and chondroitin sulfate (CS) were each modified with adipic dihydrazide (ADH) with carbodiimide chemistry. The resulting polymer was crosslinked with various concentrations of poly(ethylene glycol) dialdehyde (PEG‐diald) to produce a series of hydrogels. The physical properties of these GAG hydrogels varied in a concentration‐dependent fashion. Maximal crosslinking was observed at a theoretical crosslinking of 50% for the HA‐ADH‐PEG‐diald hydrogels and 75% for the CS‐ADH‐PEG‐diald hydrogels. Adding PEG‐diald beyond the optimum for crosslinking prolonged the in vitro enzymatic degradation time of the hydrogels. The swelling of the crosslinked GAG hydrogels was correlated with the amount of PEG‐diald used rather than with the crosslinking density. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4344–4356, 2004     

Wide‐angle X‐ray diffraction and differential scanning calorimetry study of the crystallization of poly(ethylene naphthalate), poly(butylene naphthalate), and their copolymers

The crystallization behavior of a series of poly(ethylene‐co‐butylene naphthalate) (PEBN) random copolymers was studied. Wide‐angle X‐ray diffraction (WAXD) patterns showed that the crystallization of these copolymers could occur over the entire range of compositions. This resulted in the formation of poly(ethylene naphthalate) or poly(butylene naphthalate) crystals, depending on the composition of the copolymers. Sharp diffraction peaks were observed, except for 50/50 PEBN. Eutectic behavior was also observed. This showed isodimorphic cocrystallization of the PEBN copolymers. The variation of the enthalpy of fusion of the copolymers with the composition was estimated. The isothermal and nonisothermal crystallization kinetics were studied. The crystallization rates were found to decrease as the comonomer unit content increased. The tensile properties were also measured and were found to decrease as the butylene naphthalate content of the copolymers increased. For initially amorphous specimens, orientation was proved by WAXD patterns after drawing, but no crystalline reflections were observed. However, the fast crystallization of drawn specimens occurred when they were heated above the glass‐transition temperature. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 843–860, 2004     

NMR investigation of concentrated alumina and silica slurries

The longitudinal relaxation times (T₁) of water in concentrated silica and alumina slurries were measured as a function of solids content. It was shown that the results could be fit very well with a two-phase fast-exchange model between free and surface-bound water. As expected, values of T₁ for bound water were in the order of 20–2000 times lower than that for free water, indicating a higher effective viscosity of the surface-bound water. The strength of the interaction depended on the particular surface, and all of the aluminas examined interacted more strongly with water than the two silicas studied, which themselves differed considerably. The chemical mechanical polishing (CMP) removal rate of tantalum by silica slurries was shown to be directly correlated with the interaction parameters, derived from the NMR relation times rather than with total surface hydroxyl group concentration.     

Some Aspects of the Implementation of Scaling Quantum Mechanical Molecular Force Fields

Some features of software implementation of the Pulay scaling procedure are considered. The advantages of the single value decomposition method for maintaining well-conditionality of the scale factor determination problem are demonstrated. The necessity of using a rational number of scale factors is shown. The possibility of obtaining transferable scale factors with the Pulay method and thus predict the vibrational spectra of related compounds is emphasized.     

Mechanical Properties of Blends of Low-Density Polyethylene with Chlorinated Polyethylene

The results of experimental investigation into the mechanical properties of blends of low-density polyethylene (LDPE) with chlorinated polyethylene (CPE) in tension are presented. The specimens of pure LDPE, CPE, and nine types of LDPE/CPE blends, with different content of components at 10 wt.% intervals, were examined. Data on the influence of blend composition on the tensile stress-strain diagram, elastic modulus, yield stress, breaking stress, and ultimate elongation are obtained. The results of investigations of creep are also reported. It is found that the creep compliance (the total current compliance minus the elastic compliance) obeys the power law of creep.__________Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 3, pp. 391–404, May–June, 2005.     

非保守力学系统Nielsen方程的形式不变性

研究非保守力学系统Nielsen方程的形式不变性.给出非保守力学系统Nielsen方程的形式不变性的定义和判据,研究形式不变性和Noether对称性的关系,并举例说明结果的应用 关键词： 非保守力学系统 Nielsen方程 形式不变性 Noether对称性     

用三个关系式与Mathematica软件求第二类自然数幂和公式

首先介绍三个第二类自然数幂和关系式并对其中的两式给出证明,接着利用这些关系式与数学软件M athem atica4.0,给出求解第二类自然数幂和公式的若干机械计算方法.     

Molecular dynamics simulations on the structures and properties of ε-CL-20-based PBXs ——Primary theoretical studies on HEDM formulation design

Five polymer bonded explosives (PBXs) with the base explosive ε-CL-20 (hexanitrohexaazaisowurtzi- tane), the most important high energy density compound (HEDC), and five polymer binders (Estane 5703, GAP, HTPB, PEG, and F2314) were constructed. Molecular dynamics (MD) method was employed to investigate their binding energies (Ebind), compatibility, safety, mechanical properties, and energetic properties. The information and rules were reported for choosing better binders and guiding formula- tion design of high energy density material (HEDM). According to the calculated binding energies, the ordering of compatibility and stability of the five PBXs was predicted as ε-CL-20/PEG > ε-CL-20/ Estane5703 ≈ε-CL-20/GAP > ε-CL-20/HTPB > ε-CL-20/F2314. By pair correlation function g(r) analyses, hydrogen bonds and vdw are found to be the main interactions between the two components. The elasticity and isotropy of PBXs based ε-CL-20 can be obviously improved more than pure ε-CL-20 crystal. It is not by changing the molecular structures of ε-CL-20 for each binder to affect the sensitivity. The safety and energetic properties of these PBXs are mainly influenced by the thermal capability (C°p) and density (ρ) of binders, respectively.     

Influence of annealing and chain defects on the melting behaviour of poly(vinylidene fluoride)

The melting behaviour of poly(vinylidene fluoride) (PVDF) was investigated by differential scanning calorimetry (DSC) and small- and wide-angle X-ray scattering in order to study the influence of the chain defects content and of the temperature of annealing on the crystallization and melting behaviour.All the DSC scans show a double endotherm and the analysis of the data suggests that the low temperature endotherm is due to the melting of a population of thin lamellae, whose thickness increases during the annealing, but a high content of chain defects prevents the lamellar thickening and the main effect in this case is the crystallization of thin lamellae from a portion of polymer which did not crystallize during the quenching from the melt. Furthermore, the two melting endotherms, which are observed, can be partially ascribed to a melting-recrystallization process.Furthermore, stepwise isothermal cooling was performed in a differential scanning calorimeter followed by melting scans of fractionated PVDF samples to point out the possible presence of a series of endothermic peaks.     

Dynamic mechanical thermal analysis transitions of partially and fully substituted cellulose fatty esters

The main transitions of cellulose fatty esters with different degrees of substitution (DSs) were investigated with dynamic mechanical thermal analysis. Two distinct main relaxations were observed in partially substituted cellulose esters (PSCEs). They were attributed to the glass‐transition temperature and to the chain local motion of the aliphatic substituents. The temperatures of both transitions decreased when DS or the number of carbon atoms (n) of the acyl substituent increased. Conversely, all the transitions of fully substituted cellulose esters occurred within a narrow temperature range, and they did not vary significantly with n. This phenomenon was explained by the formation of a crystalline phase of the fatty substituents. The presence of few residual OH groups in PSCEs was responsible for a large increase in the storage bending modulus, and it eliminated the effect of n on damping. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 281–288, 2003