含氰基的酚醛树脂及其碳纤维复合材料

含氰基的酚醛树脂，具有优异的耐高温性能和高温下的机械强度，在３１５℃下性能变化甚小；不着火，发烟量低，有良好的加工成型性能。热固化过程中氰基成三嗪环而交联，没有小分子脱出，是一类具有广泛发展前景的新型热固性树脂。     

Thermoanalytical procedures to identify the morphology of polycrystalline materials

Polypropylenes of differing morphologies were examined by differential thermal analysis. The problems of reordering during the programmed heating are discussed. Four potential procedures by which the reordering could be inhibited are considered, and three of these are experimentally assessed. Their advantages and deficiencies are identified. Two pretreatments, an etching and a crosslinking, are recognised as able to qualitatively characterise the initial morphology, with a preference for the former. A test to identify the occurrence of reordering is identified. In celebration of the 60^th birthday of Dr. Andrew K. Galwey     

An efficient lasing action from pyrromethene 556 dye-doped organically modified silicates

Organically modified solid-state silicates (ORMOSILS) doped with a new laser dye 1,3,5,7,8-pentamethylpyrromethene-2,6-disulfonate-BF₂ complex (pyrromethene 556) have been synthesized by a sol-gel method and the compositional effects on pore characteristics, fluorescence and lasing properties have been investigated. It is found that the use of dimethylsulfoxide and γ-glycidoxypropyltrimethoxysilane could greatly change the structure properties of sol-gel derived ORMOSILS cage, and thus the fluorescence and lasing properties of the materials could improve significantly. A successful laser oscillation from this dye-doped ORMOSILS sample has been achieved upon pumping with a Q-switched frequency-doubled Nd:YAG laser at 532 nm. A slope efficiency of 54% with a useful lifetime greater than 10,000 shots has been demonstrated at a pump repetition rate of 1 Hz and a pump intensity of 1 J/cm² by using the new ORMOSILS cage on our newly designed laser system. Our results have shown that it is possible to obtain a high-efficiency with a long-lifetime for a compact new laser device by low cost dye-doped solid-state ORMOSILS.     

High-T c superconducting magnetic bearings for rotation-based devices

Summary A Modified-Melt-Powder-Melt-Growth (MMPMG) technique has been developed for the preparation of melt-textured Y-Ba−Cu−O pellets. To test their performances, the samples were characterized with respect to their microstructure, pinning strength and interaction force with permanent magnets. A superconducting magnetic bearing was built and integrated in a levitating flywheel system for energy storage. Paper presented at the “VII Congresso SATT?, Torino, 4–7 October 1994. Under a Fondazione Confalonieri grant.     

FexNi100−x nanometric films deposited by laser ablation on SiO2/Si substrates

Fe_xNi_100−x nanometric films were deposited on SiO₂/Si substrates at room temperature using the pulsed laser deposition technique. The targets were Fe-Ni amorphous magnetic foils with composition Fe₅₀Ni₅₀, Fe₃₅Ni₆₅ and Fe₂₂Ni₇₈. Morphological and structural properties of the deposited films were investigated using scanning electron microscopy, Rutherford backscattering spectrometry, grazing incidence X-ray diffraction, and X-ray reflectivity. Electrical and magnetic characteristics of the films were investigated by using the four-point probe and the magneto-optic Kerr effect techniques, respectively. The film properties are strictly dependent on the Fe-Ni compositional ratio.     

Optimal shape design for packaging containing heating elements by inverse heat transfer method

The present study is concerned with the determination of the optimal shape for a package containing multiple heating elements. The optimization tool has been developed based on the inverse heat transfer (IHT) approach, incorporating a direct problem solver, a numerical grid generator, a direct-differentiation sensitivity analyzer, and the conjugate gradient method. Shape design that leads to a specified outer surface temperature distribution is predicted by the approach. In this study, the effects of internal heat generation on optimal shapes of the packagings have also been evaluated. Several practical cases with various imbedded heating elements and thermal conditions are studied. Results show that the approach provides an efficient computer-aided design scheme for the shape profile determination.     

用电泳技术制备YBCO高温超导厚膜

介绍了电泳技术制备YBCO高温超导厚膜的实验方法和YBCO高温超导厚膜的电学性质测量 ,讨论了在学生小型科研实验或设计实验中开展此实验的学时安排、注意事项和实验内容的扩展 .     

全光网中基于FBG的OADM设计研究

提出一种全新的OADM(Optical Add—Drop Multiplexers)结构设计，此结构仅采用一个多端口环行器，大大减少了环行器的数量，节约了成本。若要上／下路一个波长．则只需要一个FBG(Fiber Bragg Grating)；若要同时上／下路多个波长，则需要2m个FBG。计算机仿真实验证明此结构比H．Yuan提出的结构具有更低的损耗．对全光网络的实现具有重大的意义。